Question about 2003 Mitsubishi Diamante

Open Question

Remove inner tie rod on 2003 mitsubishi diamante

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 12 Answers

SOURCE: removal of inner steering tie rod

There is a special tool and you can find it at most parts stores. It is oversized a bit and you slip it over the tie rod. Then you turn in the screw on the side to tighten it on the flats. The tool will have an opening at the end to accept a 3/8 or 1/2 ratchet, depending on the tool.

Posted on Jan 23, 2009

Ad
  • 33 Answers

SOURCE: cannot get the inner tie rod off

well you can take off the wheel and remove the outter tie rod end but there is a special tool like a long tube that you need to reach in the rack & pinion to loosen the inner tie rod end they can be bought at auzone i belive

Posted on Mar 26, 2009

  • 87 Answers

SOURCE: Inner tie rod ends worn, do I have to replace the

NO just the inner tie rod and then alignment

Posted on Mar 06, 2010

  • 1 Answer

SOURCE: How do I remove a parklight bulb from the

open the trunk then twist open the lock cover thats in front of the light u want to change then change the bulb.

Posted on Jun 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have anyone out there ever change inner tie rods on a1995 honda odyssey?,if so simply explain,THANKS


Procedure on replacing the inner tie rod ends:


1) Raise and safely support the vehicle.

2) Remove the front wheel/tire assembly.

3) Clean the steering rod between the steering boot and outer tie rod end lock nut with a suitable penetrating lubricant and a clean cloth or shop towel.

4) Loosen the outer tie rod end locking nut 1/8 turn.

5) Loosen the steering boot clamp(s), and slide the small clamp off the boot.

6) Carefully loosen the boot and slide outward off the steering rack and onto the shaft to expose the inner steering rod mounting fastener.

7) If necessary, position the inner steering rack shaft in or out to allow for additional access.

8) Relieve the steering rod nut locking tab from the inner steering rack shaft, then loosen the steering rod ball socket nut 1 turn.

9) Matchmark the tie rod end to the threaded shaft.

10) Remove the cotter key and castle nut from the outer tie rod end threaded spindle, and using a tie rod end removal tool, remove the tie rod from the steering knuckle.

11) Hold the tie rod with a wrench, and remove the outer tie rod end from the threaded rod, counting the number of complete turns it takes to remove the tie rod end from the shaft. Write the number of turns on a piece of note paper.

12) Remove the tie rod end lock nut from the threaded steering shaft.

13) Slide the steering rack boot off the shaft.

14) Remove the inner steering rod ball socket nut from the inner steering rack shaft.

To install:

1) Inspect the tie rod end for looseness, and the steering rack boot and tie rod end boot for cracks deterioration or damage and replace as necessary.

2) Clean steering rack shaft and apply a light coating of Genuine Honda Power steering fluid as necessary.

3) Apply a medium strength locking agent to the threads where the inner steering rod ball socket mounts. Use a new locking washer and a new stop washer, and install the inner tie rod onto the steering rack shaft.

4) Tighten the inner tie rod end fastener by 58 ft. lbs. (78 Nm)

5) Peen the lock washer over the nut or onto the flat surface of the steering rack shaft.

6) Apply silicone grease to the outer circumference of the inner tie rod end ball socket, and onto the groove just outside of the socket.

7) Apply silicone grease to the inside of the small end of the steering rack boot, and slide the boot over the steering shaft and onto the rack and install the boot clamps. If the boot has air hose fittings make sure they are installed as removed.

8) Apply a light film of an anti-seize compound onto the threaded tie rod end, and install the tie rod end lock nut.

9) Install the tie rod end onto the tie rod, turning it in exactly the number of turns it took to remove it.

10) Install the tie rod end following the tie rod end installation procedure.

11) The balance of installation is the reverse of the removal procedure.

12) Check the front end alignment and adjust as necessary.

Sep 10, 2012 | 1995 Honda Odyssey

1 Answer

Where is the inner left and right tie rods at on a 2003 Chevy Silverado Just need to know exactly where they are


The inner tie rod ends are on the other end of the same rod as the outer tie rod ends. They should connect to the drag link and look almost identical to the outer tie rod ends. Hope this helps.

Sep 11, 2011 | 2003 Chevrolet Silverado 1500

1 Answer

I need to rplace the inner tie rods.


Inner tie rods rarely if ever need to be replaced in my experience: outer tie rod ends are far more common. Its not impossible so here's how.

1. remove the tie rod ends from the knuckle.
2. remove the clamp for the rubber bellows on the rack ends, and slide the bellows down the rod.
3. Turn the rack to fullleft or right as needed to get access to the inner rod end that screws into the rack.
4. There's a lock tab that has to be bent flat. This locks the rod end into the rack.
5. You'll need a (probably) 32mm wrench to undo the rod end from the rack.
6. Note how the lock tab is fitted to the rack/rod end.

7. Put in the new tie rods.

If your garage mechanic told you the inner tie rods are worn out, I'd ask why they think so. At step 4. above, try rotating the rod. This should be quite difficult. There should be NO evidence of slop or wear in the inner joint. What more commonly wears is the bushes on the end of the rack. These bushes are easily replacable with the rack in the car.The tie rods have to be removed to do this. So, when the rods are off, inspect the rack bushes for wear.

SD

Jun 25, 2011 | 2003 Mitsubishi Outlander

2 Answers

Need to replace inner tie rod on a 1998 ford ranger two wheel drive , driver side . engine size is 2.5. do i have to take outer tie rod off as well?


webbraymond2, Yes, you have to remove the outer tie to access the inner tie rod. When you do this, count the rotations of the tie rod as this will have to be replaced when the new inner tie rod is installed. Counting the rotations will allow you to put the outer tie rod close to where it was when you started the job. You are changing the toe setting when you have to replace either the inner or outer tie rod. You need to access and remove the jamb nut and boot before you can access the inner tie rod and this is why the outer needs to be removed first. A wheel alignment is advised after you finish the job. Good luck with this.

May 28, 2011 | Ford Ranger Cars & Trucks

1 Answer

How to install inner and outer tie rods on a 2004 Chrysler Pacifica - I waqs told buy a trusted local mechanic that I need to replace 3 of the 4 tie rods. Might as as well replace all 4, but how hard is it...


You will need to rent or borrow in inner tie rod tool but here are the directions.
1. Break the jam nut on inner tie rod to outer loose.
2. Remove nut from outer tie rod attaching it to steering knuckle.
3. Use hammer to get tie rod out of knuckle.
4. Unscrew outer tie rod then jam nut
5. Remove clamp from boot and slide off inner tie rod.
6. Using side cutter or hammer and chisel break off metal clamp on the inside of inner tie rod boot.
7. Using inner tie rod tool, unscrew inner tie rod from rack and pinion
8. Reinstall parts and have it aligned

May 06, 2010 | 2004 Chrysler Pacifica

1 Answer

How much does it cost to repair a tie rod on a 2003 nissan altima


Depending if power/streeing or manuel/streeing.
Inner tie rod $50.00 - $150.00 each part only.
outer tie rod $30.00 - $75.00 each part only.
labor 1.0 flag rate on outer tie rod per side.
labor 1.3 flag rate on inner tie rod per side.
Flag rate X shops hourly rate = labor cost.

Dec 27, 2009 | 2003 Nissan Altima

1 Answer

How too change inner tierod on 2005 pontiac g6


If you have electric steering(no power steering pump)you have to change the entire steering gear assembly as no part is available.If you have the system with a pump a part is available.In order to change the inner tie rod you would loosen the 21mm lock nut on the tie rod.remove the 18mm nut on the outer tie rod and spin off after removing the outer tie rod from the steering knuckle.Remove the nut and the inner and outer clamps on the tie rod boot.remove the boot.You would then need a special inner tie rod tool to turn the threaded inner rod from the steering gear.

Oct 17, 2009 | 2005 Pontiac G6

1 Answer

Cannot get the inner tie rod off


well you can take off the wheel and remove the outter tie rod end but there is a special tool like a long tube that you need to reach in the rack & pinion to loosen the inner tie rod end they can be bought at auzone i belive

Mar 26, 2009 | 2004 Mitsubishi Lancer

1 Answer

How to replace inner tie rods on lancer


I had my outer tie rod end go bad in my 2002 lancer oz and i just bought the pairs and took it in and it total costed me 200. but could be less. I would take it in to a tire shop. thats what i did.

Feb 25, 2009 | 2002 Mitsubishi Lancer

Not finding what you are looking for?
2003 Mitsubishi Diamante Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8589 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...