Question about Chrysler Cars & Trucks

Open Question

How to replace heater core 1980 chrysler lebaron

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 27 Answers

SOURCE: heater core

its a pretty big job. Basically the entire dash has to come apart to get to the heater core

Posted on Sep 10, 2008

emissionwiz
  • 75822 Answers

SOURCE: REMOVING THE DASH

it is not ness to remove the dash.

Drain cooling system.
Remove inlet and outlet hoses from heater core.
Remove lower right hush panel.
Remove lower trim panel.
Remove heater case cover screws.
Remove heater case cover.
Remove core support plate baffle screws.
Remove heater core, support plate and baffle from car.
Reverse removal proceedure to install.
Refill cooling system and check for leaks.

Posted on Nov 08, 2009

  • 114 Answers

SOURCE: 1994 chrysler lebaron 3.0 Ignition started

You have lost the accessory power feed due to high resistance at the ignition switch connector.
Most likely the switch will need to be replaced and if the harness plug is not heat damaged too bad you may be able to clean and crimped the terminals a little for better contact. In some cases you can buy just the connector end from the dealer as a repair part.

Posted on Mar 01, 2010

  • 1 Answer

SOURCE: how to replace heater core

how to take out my heater core in a 2000 lhs

Posted on Nov 12, 2010

weekspena
  • 375 Answers

SOURCE: how do you replace heater core on chrysler 300m

If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing

  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core. Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Posted on Jan 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is it possible to by pass the heater core using s splitter on the hose


yes disconnect both hoses to heater and hose clamp together with connecter

Jan 16, 2012 | 1994 Chrysler LeBaron

1 Answer

Why won't the heat work in the Lebaron


Had this problem in mine! The heater core ended up being the solution. It had coated up with a white residue insulating the heat from being exchanged in the vehicle. Mechanic said core would have to be replaced as flush would not work!

Here is what did work. I disconnected the heate core lines on the firewall, connected two new lines for flushing purposes. I filled the core through the lines with a funnel with CLR or the equivalent brand. That is the Calcium, Lime, Rust remover you get at any hardware store. I hooked up a drill with a fluid pump on it and circulated the solution periodically while letting it sit overnight.

The next day I flushed the core several times with a garden hose into a pail in my garage (as it was this December), in both directions.

Hooked the lines back up (added some foam 3/4 inch pipe wrap insulation while I was there) and nearly burnt my hand when I first tested it. Saved myself $1000 heater core replacement that I was quoted. It takes 9 hours to replace the heater core so I had nothing to lose!

Very cozy this winter in my 95 LeBaron!

Feb 08, 2011 | 1995 Chrysler LeBaron

1 Answer

I have a 92 chrysler lebaron and there is very little heat coming from the heater. The engine is at operational Temp but no heat.


either the heat control valve isn't working, or the heater core is plugged up, what i do is reverse the heater hoses on the core to unplug the core sometimes that is all it takes but if its plugged badly you will need to replace it

Jan 05, 2011 | 1992 Chrysler Lebaron

1 Answer

I had my heater core replaced which involved removing the dash now my interior lights stay on all the time. I had to remove the fuse. any sugjestions


Check the two switches at the door striker on both sides. This should not be related, but see if one of those switches disconnected puts the light out.

Too bad I just saw this as I have a solution I just posted for a cleaning a heater core which goes bad from calcium deposits. If it was leaking then nothing you could have done, but some of these have problems with not heating and it is easily fixed without replacing the core.

Dec 28, 2010 | 1995 Chrysler LeBaron

1 Answer

We bought a 1988 Chrysler LeBarron and cannot seem to get HOT air to blow. It is barely warm and we've replaced the thermostat, radiator, heater valve and we have checked the heater core and it has great...


Could be thermostat. Even though you had it replaced the recommened temp is 192. You probably have a thermostat with an alternative temp of 160 or 180. This will make your car run alot cooler than it should.

Oct 06, 2010 | 1988 Chrysler LeBaron

1 Answer

I need to flush the radiator can you tell me how?


best thing is to get a "Coolant tee" from the parts store

you cut this into a heater core hose

makes life simple!!

May 31, 2010 | 1995 Chrysler LeBaron

1 Answer

1994 chrysler lebaron 3.0 Ignition started


You have lost the accessory power feed due to high resistance at the ignition switch connector.
Most likely the switch will need to be replaced and if the harness plug is not heat damaged too bad you may be able to clean and crimped the terminals a little for better contact. In some cases you can buy just the connector end from the dealer as a repair part.

Dec 27, 2009 | 1994 Chrysler LeBaron

1 Answer

Heater Problems


It goes on the hose coming from the water pump.

Oct 29, 2009 | 1983 Chrysler Fifth Avenue

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...