Question about Nissan Pickup

Open Question

Nissan navara 1990 z 2.4 petrol how to set ignition timming

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

old marine
  • 1973 Answers

SOURCE: Nissan navara 1986 2.4L petrol timing problem

For timing, on 1981 and later 4 cyl engines (from the Haynes manual):
1. Turn camshaft so both valves for #1 cylinder are closed, and turn the crankshaft so #1 piston is at top dead center (woodruff key should be pointing up).
2. Engage the camshaft sprocket (with stamped numbers facing out) into the timing chain, and install the chain around the crankshaft sprocket. The bright links on the chain should be aligned with the timing mark on the crankshaft sprocket (on the right side as you look at it) and with the number "2" stamped into the camshaft sprocket, which should also be on the right side as you look at it.
3. Install the camshaft sprocket onto the camshaft, aligning the camshaft dowel pin with the number "2" hole near the center of the sprocket.

For the firing order and wiring routing for the 8 plug 4 cylinder engine: (Plugs on the intake manifold side are coded "I", and on the exhaust manifold side are coded "E")

Wire to 1I should be connected to tower on the distributor facing directly to the front of the vehicle. Going counterclockwise from there, the order is (1I), 2E, 3I, 1E, 4I, 3E, 2I, and 4E.

Posted on Jan 09, 2009

alicantecoli
  • 22131 Answers

SOURCE: 2002 Nissan Navara will not start after changing battery

dealer only to reset factory immobiliser

Posted on Jun 20, 2009

chris bean
  • 61 Answers

SOURCE: nissan navara 2006 blown hole no1 piston 16000kms

do you have a hole in the piston or gasket? If in the piston it is most likely from coolant or water. If water, could be a cracked head, or being sucked in through the intake and building up in the 6th cyl. I have a lexus that had a hole in the side of the motor and noon could figure out why. I pulled the head and found water... Put new block in and egr codes came up. Pulled EGR and found it was sucking in water, due to an exhaust leak that was allowing condensation to build and would not blow out once in the egr tube. If you face the same problem (hole in block) I am going to say too much compression. Could be from head gasket not being torqued properly and leaking cooland, cracked head, or wrong spark plugs-and worst case scenario which I have yet to witness, bad spark plug gap. Not likely on your car, i would think.

Posted on Mar 29, 2010

  • 1 Answer

SOURCE: when does a Nissan Navara require a service

how do you replace the power steering belt on a d22 nissan navara.

Posted on Mar 29, 2010

  • 1 Answer

SOURCE: 2007 Nissan Navara Service ligth reset.

You will need to send the navara workshop it needs to be hooked up to a special computer to be reset.

Posted on Mar 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Z20 engine. what is the optimum idle timing if running on lpg


standard petrol and LPG have very close to the same octane rating so the timing setting for petrol would be the same for the LPG timing setting

Dec 19, 2013 | Cars & Trucks

1 Answer

Im needing the torgue settings of the cylinder head bolts and big end bearings for a Nissan Navara 4.0 V6 Petrol engine..


Hi mate,

I did forget to tell you to ensure that you turn the connecting rod bolts a further 90 degrees after the first setting.

Thanks

Jason

Jul 14, 2010 | Nissan Pathfinder Cars & Trucks

1 Answer

Can you please tell me timing chain set up for nissan navara 2.4 petrol motor year 1999


probably very similar to the early bluebirds or 180Bs..chain goes around all the sprockets,and kept tensioned by a oil pressured tensioner,.normally dont give any problems

Jun 29, 2010 | Cars & Trucks

1 Answer

Ignition


Not adjustable. All controled by ECM/computer.

Sep 28, 2008 | 2000 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...