Question about Fiat Cars & Trucks

2 Answers

CLUTCH OR SLAVE CYLINDER?

I was driving the car the other day and all of a sudden the cluctch gave way with no sign what so ever it was in second gear when it went and i couldnt change gear from there it just stuck. could this be the slave cylinder or is it the clutch? either way what am i looking at for replacements? and how hard of a job is it?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Is there any fluid lost

Posted on Jun 25, 2015

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,101 Answers

The clutch is manual. which it can be bleed like brakes . it has a bleeder valve. sounds like the clutch slave cylinder blow .is there any fluid leaking

Posted on Dec 03, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Keith100881
  • 74 Answers

SOURCE: put in new clutch and slave cylinder. no clutch pedal. how do you bleed the cylinder?

work it back and forth with your hand and you will get pedal after a while then bleed like you would brakes get help so one can pump and the other can bleed

Posted on May 24, 2009

  • 6982 Answers

SOURCE: leaking clutch fluid Where is the slave cylinder"..I have been told to look at the slave cylinder because I do not see fluid under the car.

Slave cylinder should be on the left side of the bellhousing (follow the line from the clutch master if necessary) If you don't see fluid but you have lost some, also check where the rod from the pedal goes through the firewall to the master...they often leak there and will not drip on the ground.

Posted on May 30, 2009

  • 145 Answers

SOURCE: after replacing starter and removing slave cylinder, clutch fails to work

sounds like you have a air pocket or you fail to engage the slave cylinder push rod If you disconnected the slave cylinder from the hose proceed to bleed out the slave cylinder if you didn't take you slave cylinder and whit out disconnecting the hose and make sure the push rod is against the clutch push arm.

Posted on Jun 13, 2009

  • 2187 Answers

SOURCE: clutch slave cylinder replacement or repair -

You will have to replace the rubber and the piston like mechanism to get this done. If you found an assembly replacement for the entire clutch slave, the better. The leaks may be caused by faulty rubber or valve on the piston but this can be caused by the linings of the cylinder becoming rough due to wear and tear.

Posted on Aug 20, 2009

  • 70 Answers

SOURCE: no clutch pedal been bleeding it for 3 days

these are notorius for clutch bleeding problems, there is no good answer other than to keep pumping that pedal, eventually it will bleed out

Posted on Dec 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 90 ford probe lx will not drive unless i start it in second gear and will not shift in any gears when clutch is applied. Clutch master replaced and clutch. What else can be the problem???


See if your slave cylinder needs bleeding. Follow the line from the master cylinder down to the bell housing to find the slave. When clutch pedal is pressed, a rod on the slave should move outward just a little. It will move the clutch fork to engage the clutch.

Feb 17, 2016 | Ford Cars & Trucks

2 Answers

2001 Camry 5 speed. It starts but it will not move. I can change gears without pushing in clutch. One mechanic said it was clutch and a different one said transmission is out. Which is it?


The clutch is not transferring power to the gearbox, which then is not turning, so that you can select gears without the clutch.Possibilities are
- clutch assembly has failed, possibly by the splined driven plate hub coming adrift
- clutch driven plate has become very worn and has lost contact
- slave cylinder has stuck through corrosion (assuming a hydraulic clutch) and is holding out the clutch independent of the pedal. This can be determined by watching it while someone depresses and raises the pedal.

I think it is unlikely the transmission input shaft has fractured.

Aug 14, 2015 | 2001 Toyota Camry

3 Answers

The clutch was having a hard time going into gear.All of a sudden there was a high pitched squeal/scream coming from the transmission area.


that sounds like a throw out bearing failure-is there any adjustment at the slave cylinder-it may be holding the bearing against the clutch and causing the noise-this thread may help-http://www.jeepforum.com/forum/f9/how-change-bleed-clutch-slave-cylinder-511531/- cheers Denny

Dec 22, 2013 | 2000 Jeep Wrangler

1 Answer

Mitsubishi clutch problem


Its your slave cylinder down by the bellhousing. It got loose, slipped out of its mounting position, and has squeezed out as far as it will go. Since its not pushing against anything, there was nothing to re-compress it, thats why you pedal didn't come up. Replace slave cylinder on side of bell housing, and bleed your cluctch properly, your will be good.

Dec 12, 2013 | Cars & Trucks

1 Answer

CLUTCH OR SLAVE CYLINDER?


what is the make model and year please

Dec 03, 2012 | Cars & Trucks

2 Answers

92 jeep cherokee, manual, gear shift resistance


hi, if when you put it into gear and you lift your foot off the clutch then if your engine revs up without the actual power going to the wheels like when you say the revs change this indicates that your clutch is slipping, i wouldnt say their was a problem with either the cylinder master or slave and i wouldnt say it needed flushing out the problem you are having it that your clutch is slipping due to it being to low.

You need to get the clutch replaced sooner rather than later due to the fact that if your clutch plate shatters due to it being running on the rivets and not the actual clutch plate then this can cause the clutch to collapse and this will then cause damage to the master and slave cylinder and if you was driving at the time you would have no clutch at all and the car would be stuck in gear and you wouldnt be able to tow it as it would be stuck in gear.

You need to get the clutch and pressure plate the thrust bearing changed this will then solve your problem.

let me know how you get on or if you need further assistance ok

Jan 27, 2010 | 1992 Jeep Cherokee Sport

2 Answers

1989 jeep wrangler wont shift gear and clutch gone loose


Get the clutch slave cylinder and master cylinder looked at.One of the 2 has failed.If the pedal goes to the floor or is very loose,this is very likely the cause.Not an expensive fix.Hope this helps

Jan 10, 2010 | 1989 Jeep Wrangler

2 Answers

99 dodge avenger gears will not engage


if it happen all of a sudden then its most likely the clutch slave cylinder.

Dec 07, 2009 | Dodge Avenger Cars & Trucks

3 Answers

Car wont go into gear


Have you ever replaced the clutch? If not you may need a new cluctch. It could also be your clutch slave cylinder.

The latter is much less expensive and in some cars very easy to change (i did it myself on an old Mazda Rx-7 and I'm a girl!). Hope these suggestions help.

Jul 10, 2009 | 1996 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fiat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Fiat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...