Question about 2004 Chrysler Sebring

Open Question

Where is the oil pressure sensor on 2.7 2004 Sebring

Need a location on the engine for the oil pressure sensor

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 202 Answers

SOURCE: 2002 Chrysler Sebring Oil pressure light

Could be a bad oil pressure switch, or a bad oil pump. Both will cause this issue. Hope it is the switch b/c the oil pump is a costly repair.

Posted on Mar 26, 2009

Molson02536
  • 3854 Answers

SOURCE: camshaft position sensor

This V-6 has a very hard to find/hard to reach CKP - it is directly under the Distributor, about 4 inches below, inwards toward the Transaxle "bell". Almost dead-center in the back of the engine.
Your going to have to take the Air Filter and the air manifold that runs to the engine off. After that, take off the horn assembly to gain very, very limited access to wedge an extended ratchet into the bowels of the engine. 
I think the same socket that undid the horn assembly fit the CKP nut. It takes 10 minutes to undo the bolt a couple ratchet clicks at a time, at least 15 to get the thing to wiggle out, probably 15 minutes to unconnect, reconnect, and snap back to the fram the wire harness, and at least another 10 minutes to ratchet the bolt back in click by click.

Now you know why they say shops charge $500 in to do this - I think they must take the entire engine out... Very painstaking job that requires patience and precision... but quite satisfying to finish it yourself. 

Good luck and hope this helps, 

Posted on Apr 23, 2009

BCAS1298
  • 3092 Answers

SOURCE: Where is the oil pressure sensor located on a 2001

Sit right next to the oil filter.

Posted on Dec 26, 2009

01fordeb
  • 1033 Answers

SOURCE: oil sending unit on 2004 chrysler sebring V6

Should be located close to the oil filter. It will screw in like a spark plug. It has a harness plug. Easy to change, save yourself $70 in labor. You will need a fairly large wrench to remove

Posted on Jan 03, 2010

  • 55 Answers

SOURCE: location of oil switch 2002 chrysler 2.7 engine

should be on driver's side right above the oil filter

Posted on Jul 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change oil ressure switch in 2004 chryler sebring lxi 2.7 engine


first off if the oil warning light is on, u need to check the oil pressure with a gauge with the engine at operating temp. and make sure oil pressure is up to spec. a bad switch can cause it to come on also. on the backside of the engine there is an aluminum heat shield covering the switch held on with 3 15mm bolts. after you remove the shield the switch can be removed with a deep socket. dont over tighten the new one when you put it in.

Feb 24, 2015 | 2004 Chrysler Sebring

1 Answer

Where is the oil sensor is located on a 2001 sebring 2.7 engine?


the dealer will tell you exactly with a diagram printed out

Aug 25, 2014 | Cars & Trucks

1 Answer

Where is the oil sending unit on a 2004 v6 sebring


The oil pressure sensor is located on the back of the engine, behind a heat shield. you will need to be able to work from under the vehicle to access it.

Jan 20, 2011 | 2004 Chrysler Sebring

2 Answers

Last night my sebring stalled out of nowhere and then the check engine light along with the oil pressure light appeared. There was no unusual knocking sounds or anything. I keep the oil changed and up to...


Get it scanned for the check engine light, (mil light), as for the oil light, thats normal due to engine not running and making no oil pressure. was this a sudden stall, with no engine surging, then I suppect a failed cam or crank sensor. if it kind of stalled with engine surge and hesatation, I suspect fuel related, possible fuel pump. 2.4L, 2.7L engine have same sensor issues and ideas. if you need more info, just reply back with the mil code, I will walk you through this problem.
GOOD LUCK, RDJRP.

Jul 17, 2010 | 2001 Chrysler Sebring

1 Answer

Where is the oil sending unit on a 1996 ford taurus 3.0 liter engine located? glenn


On 3.0L OHV engines, the oil pressure sensor is located on the left side of the engine block above the flywheel. On 3.0L DOHC engines the sensor is located on the left side of the engine block above the oil filter. On 3.4L DOHC engines the sensor is screwed into the oil filter adapter. The oil pressure sensor operates the oil pressure warning lamp.

71f6e37.jpg
Fig. 1: Location of the oil pressure sensor-3.0L OHV engines


046f42b.jpg Fig. 2: Location of the oil pressure sensor-3.0L DOHC engines

69cce3e.jpg

Fig. 3. The oil pressure sensor-3.0L OHV engine

Hope help with this (remember rated this help). Good luck.

Feb 18, 2010 | 1996 Ford Taurus

5 Answers

Oil light comes on only when at an idle


I just had the same problem on an 04 Sebring with a 2.7L V6. The oil pressure sensor (switch) was the culprit. Several web references that I checked mention that the original sensors have issues with oil leakage, which eventually causes it to fail. The sensor itself is fairly inexpensive..about $15. It is located on the back side of the engine and is only accessible from under the car. Look for a small heat shield held on by three 15mm bolts. It is just to the driver's side of where the exhaust system goes behind the engine. The oil sensor is located under this shield. You will need a 1 1/4" deep socket to remove it. When installing the new sensor, be sure to use a torque wrench. It needs to be tightened to 14 ft/lb. Using more force than that, and you run the risk of damaging the sensor.

If this doesn't resolve the problem, you may have a problem with the oil pump either being defective or blocked with sludge. As one of the other gurus on here mentioned, this engine does have a known problem with sludge buildup. I hope this helps! Good luck!

Oct 30, 2009 | 2004 Chrysler Sebring

3 Answers

2000 Chrysler Sebring V6 oil pressure light comes on when oil is warm. Replaced the seals and value cover and still the light comes on while Idel now drops below 5 rmp


Here is how I fixed the low oil pressure light problem without using any parts, only the labor to remove the oil pressure sensor is needed. I have an 02 seabring convertible 2.7L engine and I was having the same problem with my oil light coming on at an idle. I bought a new sensor replaced the old one and had the same problem. I than got a test kit and tested my oil pressure. It was very good, never lower than 11 PSI hot at an idle. I was reading about the wire connector modification, but I had an 02 and this mod came out in 98, surely Chrysler incorporated this mod on its newer vehicles. Well after checking more they did not and this is what turned me off on Chrysler products forever. For a manufacturer to produce a vehicle with a known defect and a modification fix and not incorporated this modification on its newer vehicles is inexcusable. After reading that the modification was to stop pressure build up in the sensor housing I decided to make a pressure release hole in the sensor housing. I took my old oil pressure sensor and using a 1/8 inch bit I drilled a small hole at the base of the plastic sensor tower. I put the old sensor in and drove for a week, no problem with my light coming on. To test further I took the new oil pressure sensor I bought and drilled a hole in it. Put it in and I've been driving for months and no problem with my oil pressure light coming on now.

Mar 07, 2009 | 2000 Chrysler Sebring

3 Answers

02 Sebring, oil light doesn't come off


do you have the 2.5l engine ?this is a very common problem with them Oil pump you will start hearing the valves ticking on start up when the engine is cold
i you have the 2.7 l just kiss the engine good buy oil sludge is a problem with that Eng that's why thay do not have any resale value

Sep 30, 2008 | 1999 Chrysler Sebring

1 Answer

2004 sebring


If you are talking about the change oil message on your cluster. You need to press step until oil change mileage appears on screen and then just press reset.

If you are inquiring about the oil pressure swith on the engine there is no reset procedure. If you just replaced the oil pressure switch and still have no oil pressure, you are going to have to use a manual oil pressure gauge to make sure that you have engine oil pressure. If you have oil pressure with the manual guage there is a problem with the wiring or engine computer.

Jun 26, 2008 | 2004 Chrysler Sebring

Not finding what you are looking for?
2004 Chrysler Sebring Logo

Related Topics:

288 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...