Question about 2002 Toyota Sequoia

Open Question

Just changed front rotors and disk, now the brake light and trac loc and vsc light stay on.

I bled the brakes and test drove. Brakes are working fine. Is there something in the computer that needs to be reset?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Brian032472
  • 150 Answers

SOURCE: 98 Camry brakes

I would suggest replacing the caliper hoses and following a proper bleeding procedure before replacing the master cylinder

Posted on Nov 19, 2008

SOURCE: toyota sr5 brakes slip

Did you adjust the rear brakes?

Posted on Nov 24, 2008

  • 245 Answers

SOURCE: ABS alarming after I replaced rear brakes shims, bled brakes etc.

try rebleeding the brakes. any air whatsoever will set off the abs light sometimes it takes a few times to get it all out even though they feel good. also make sure the fluid is full that will also set off the light.

Posted on Jul 01, 2009

  • 107 Answers

SOURCE: I changed the brake pads and rotors. After

did you foll your brake resiviour? it need to be at full level to turn off the lite. its under the hood drivers side firewall fill it good luck CJ. .

Posted on Jun 01, 2010

  • 1 Answer

SOURCE: my VSC trac, TRAC off & brake light is on

I have a 2004 sequoia with the same problem. VSC TRAC, TRAC OFF & brake light comes on at the same time. Sometimes just the brake light and other times all three. Sometimes no lights. Does anyone have a fix?

Posted on Jul 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2001 Sequoia replaced connectors to battery. Now E brake light ABS light Trac Off and VSC Trac light are on. I disconnected ground and let it sit. Had code ran and it said open closed circuit abs?...


More than likley its your VSC computer (VSC Trac, VSC Off, E brake and ABS brake lights all lit). This problem has been sited on other Sequoias that had the TSB brake caliper/rotor upgrade (recall) and that more than likely the VSC software or computer was not updated to meet the demands of the newly installed brake upgrade.

Nov 19, 2013 | Cars & Trucks

1 Answer

VSC error camry


Your pressure is air.. Try bleeding again then clear the codes with obd code reader.. The thing is that the brakes have nothing to do with the rotors and should have never been bled... Good luck...

Apr 09, 2013 | 2008 Toyota Camry

1 Answer

I changed the rear brakes and rotors on my Lexus rx330 and drove it for a day and the BRAKE(all red) light came on... I have Bled(sp?) the brakes in the proper order, took the brakes and rotors off again...


Did you check the brake fluid level? A low level might cause the light to come on.
If it's 1997 or newer, and then likely OBD2, take it to a local autozone or similar parts store. Most should scan and clear codes for free, hoping you will then buy parts from them.

May 26, 2017 | 2005 Lexus RX330

1 Answer

After replacing master cylinder pads and rotors bled brakes test drove low pedal only one wheel grabs front passenger side abs lite on


You may still have air in the hydrolic brake system.
Follow these steps to insure you do not have any air hiding.

You will need:

A couple 8oz bottles of brake fluid.

A box wrench that fits the bleeder bolt.

A piece of clear plastic tubing (aquarium tubing is fine, and it

Apr 07, 2011 | Pontiac Grand Am Cars & Trucks

1 Answer

ABS light and Trac Cont light stay on....


Check your rear brakes and inside the rear Rotors. There are ABS scanners and if Autozone or Oreillys have that type of scanner, they will scan for free.

Because the Trac Control is on the Rear axle all of your problems are probably rearward. What usually happens is the Emergency brake material and the Rotor pads wear down and blind the sensors. Sometimes the Trac Control will destroy the brake linings. The Trac Control works by applying the rear brake to the fastest spinning wheel in an effort to match each rear wheels speed.

When the sensors have debris flying in front of them, they miscount and include the debris in figuring RPM. Someone needs to disassemble and inspect the back brakes.

Jul 13, 2010 | 2000 Mercury Grand Marquis

1 Answer

I changed the brake pads and rotors. After


did you foll your brake resiviour? it need to be at full level to turn off the lite. its under the hood drivers side firewall fill it good luck CJ. .

Jun 01, 2010 | 2006 Toyota Sienna

1 Answer

1998 Buick Century Low Trac light comes on and car skips.


have you bled the brakes? If you have, you may need to do it again as there sounds like there's an air lock in your lines.

Mar 14, 2010 | 1998 Buick Century

1 Answer

Pistons in both front calipers stay out, both calipers replaced


You may have a leak in the booster or master cylinder. You can put a pressure tester on the system to test for leaks. It does sound like you have an air leak.
You can try to bleed the master cylinder, then slave cylinder, then brake lines.

Aug 24, 2009 | 1993 Oldsmobile Achieva

2 Answers

ABS alarming after I replaced rear brakes shims, bled brakes etc.


make sure that the abs connect for that side is connect properly and the right amount of brake fluid is there

Jul 01, 2009 | 2003 Toyota 4Runner

Not finding what you are looking for?
2002 Toyota Sequoia Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...