Question about 1994 Chevrolet S-10 Blazer

Open Question

How do u bleed brakes on a 1994 chevy s10 blazer

I changed my front brakes and calipers and bleed them first the front right started to stick and then the brakes went to the floor

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
280zlvr
  • 126 Answers

SOURCE: unable to bleed front brakes

loosen the front brake line that goes to the master cylinder fill master cylinder up with fluid and bleed it first by attaching a flexible line from master cylinder front brake side submerge that line into jar of brakefluid keeping air from entering line get someone to pump brake pedal while ur holding line in a jar keep refilling the brake resivoir so no air gets in, once the master is bled front brake side then reattach the origional brake line then remove bleed screw from caliper and let fluid gravity flow down to calliper then bleed the normal way. more than likely your master cylinder has air trapped in the front portion good luck

Posted on Jul 01, 2008

Ad
  • 2 Answers

SOURCE: Brakes no longer work in 1989 Chevy half ton pickup 2 wheel drive 350cubic inch

change dump valve under master cylinder

Posted on Aug 17, 2008

  • 82 Answers

SOURCE: 1999 Chevy S10 Blazer 4x4. Replacing rear pad's,& Bleeding Breaks

have one person in the blazer pumping the brake pedal and then hold to the floor, crack the bleeder then tighten, release pedal, repeat till all air is out one side at a time, if this does not work then your ABS unit is bad witch if u follow your lines from your master cylinder u will find a black box with a motor on it, or the master cylinder itself is bad, it also can cause u to have no pedal, replace the master cylinder first, most likely cheaper.

Posted on Mar 11, 2009

  • 156 Answers

SOURCE: 98 chevy S10.Tried bleeding brakes,Front ok,Rear not reacting

Check the master cylinder and make sure it is working correctly and both resevoirs are full.

Posted on Jun 28, 2009

andreousb
  • 4 Answers

SOURCE: 1994 CHEVY BLAZER W/AC S10 HEATER CORE

The link below helped with mine and has pictures as well. Good luck!
http://www.sytyarchives.com/howto/viewarticle.php?article_name=heater_core.php&dir=climate_controls

Posted on Oct 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chevy blazer brake pedal going to the floor when engine is running


has to be air,try bleeding without the brake pedal,just open
the bleeders and let gravity run the fluid out,takes awhile but works.
(master cyl.cover off )

Dec 25, 2012 | 1999 Chevrolet Blazer

1 Answer

I was given a 1994 s10 Chevy Tahoe vortex blazer


I was given a 1994 s10 Chevy Tahoe vortex blazer??????? It's either a S-10 pick-up or it's a Tahoe or a Blazer not all three . So which is it ?

Mar 11, 2017 | 1994 Chevrolet S-10 Blazer

1 Answer

Where is the bleeder valves for brakes on 94 chevy s10 blazer


There is 1 in each brake caliper, around the top of the caliper. The wheel cylinders have bleeders coming from back of the wheel cylinder, on the back side of the brake backing plate.

Oct 19, 2010 | 1994 Chevrolet S-10 Blazer

2 Answers

Brake pedal on my 98 chevy s10 is soft


1988 chevy r 3500 1 ton changed out driver front brake caliper
brakes are soft peddle goes to the floor tried to bleed but no brake fluid will come please help

Apr 14, 2010 | 1988 Chevrolet C1500

1 Answer

Just changed rear disc pads and one caliper on 2001 Chevy Blazer...now rear brakes are not working at all...fluid is in lines as it comes out when bleeding...help!


the problem here is in order to bleed the brakes properly u need to have a special tool to open up the ABS high pressure pop-it valves, this special tool will be avail at the dealer or in a generic form at any well equiped front end shop, u just can't bleed the brakes without it, I see this same posted problem over and over, this information is correct, u will need a shop to bleed the brakes

Feb 16, 2010 | 2001 Chevrolet Blazer

1 Answer

Brakes to the floor(almost) 99 blazer


bleed the brake again. if the pedal goes to the floor with little resistance, then the master cylinder is your problem.
the shim is to depress the noise when you applied the brake. you can skip that, if the brake works without it.

Apr 29, 2009 | 1999 Chevrolet Blazer

2 Answers

Right front brake engages but doesnt disengage. master cylinder is basically new put it on then parked it for two years now this is happening.


Have you removed, checked,cleaned & lubed calipers? FYI , After sitting for 2 years, all brakes should be inspected, clean & lubed, as well as conditions of fluid lines.

Apr 11, 2009 | 1991 Chevrolet S-10 Blazer

2 Answers

Changed break line but still have no pressure in breaks


to do a complete job. you need to bleed all 4 wheels, starting from Right Rear. Right front. Left Rear. Left Front.

Apr 07, 2009 | 1995 Chevrolet Silverado 2500

2 Answers

I need to know how to bleed the brakes on a 1999 chevy blazer


Start from right rear, then, left rear, right front, left front. Fill master cylinder. Have helper sit in car, have helper hold brake pedal down. open bleed screw. fluid and air comes out. close screw. release brake pedal. Continue until no air comes out. Move to next wheel. Keep an eye on master cylinder fluid level after each wheel.

Mar 27, 2009 | 1999 Chevrolet Blazer

1 Answer

1999 Chevy S10 Blazer 4x4. Replacing rear pad's,& Bleeding Breaks


have one person in the blazer pumping the brake pedal and then hold to the floor, crack the bleeder then tighten, release pedal, repeat till all air is out one side at a time, if this does not work then your ABS unit is bad witch if u follow your lines from your master cylinder u will find a black box with a motor on it, or the master cylinder itself is bad, it also can cause u to have no pedal, replace the master cylinder first, most likely cheaper.

Mar 11, 2009 | 1997 Chevrolet S-10 Pickup

Not finding what you are looking for?
1994 Chevrolet S-10 Blazer Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...