Question about 1999 Dodge Dakota

1 Answer

No turn signals 1999 dodge dakota

Have had the combination/multi function switch checked and that's not it ... any other suggestions?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 82 Answers

Try checking the fuses if you haven't already.

Posted on Jan 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My low beam works on both sides but not the high beam on the drivers side. also my blinkers dont turn on or blink but, if you use your hazards they turn on and blink on my 2001 dodge dakota v8


Headlamp operation is controlled by the central timer module. If 10A fuse 11 in the junction box is OK, the module could be defective.

Turn signal operation is determined by the position of the multi-function switch in conjunction with the combination flasher. If 10A fuse 19 in the junction block is OK, the flasher could be defective

Dec 09, 2012 | 2001 Dodge Dakota

2 Answers

1999 Dodge Durango head lights don't work but the park and fog lights do? What do I need for them to work?


If your headlight switch is bad,this video will show you how to replace it.">

Nov 21, 2010 | 1999 Dodge Durango

1 Answer

I need instructions on replacing a turn signal switch. Our current turn signal is no longer returning or cancelling.


For Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004 check this guide for change Turn Signal Switch:
CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before working around the air bag or SIR system wiring. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.
  1. Disconnect and isolate the negative battery cable from the battery.
  2. In order to disarm the air bag system, allow the system capacitor to discharge for at least 2 minutes, before performing any removal procedures.
  3. Remove the upper and lower steering column shrouds.
  4. Disconnect the electrical connector from behind the combination switch.
  5. Remove the mounting screws securing the combination switch to the steering column adapter collar.
  6. Remove the combination switch from the vehicle.

    7e690ec.jpg
    Fig. The turn signal (multi-function) switch is attached to the steering column by two screws

To install:
  1. Install the combination switch to the steering column adapter collar. Tighten the combination switch mounting screws.
  2. Reconnect the electrical connector to the combination switch.
  3. Install the upper and lower steering column shrouds and tighten the retaining screws.
  4. Reconnect the negative battery cable and check all functions of the combination switch for proper operation.

Hope helps (remember rated this).

Jul 01, 2010 | 2002 Dodge Grand Caravan

1 Answer

Rear brake lights and turn signals do not work people say switch in steering columb


the turn signal switch (Multi function switch) is the likely suspect

Jun 10, 2010 | 1999 Dodge Caravan

1 Answer

Ihave a 1999 box cherokee. The turn signals won't come on but the hazards will?


Assuming all bulbs are good, you could be looking at the Combination/multi-function switch/module. Basically it's your blinker arm switch which is attached to a module that is housed in the steering column.

Apr 29, 2010 | 1999 Jeep Cherokee

1 Answer

I need instructions for replacing the turn signal multi-switch on my 1999 Dodge Dakota SLT.


  1. Remove the negative battery cable.
  2. If you have tilt remove the tilt lever.
  3. Remove the upper and lower shroud.
  4. Remove the lower fixed column shroud.
  5. Move the upper shroud enough to access the back of the multi-function switch.
  6. Remove the tamper proof Torx screws (Snap on TTXR20B2 bit or equivalent).
  7. Gently pull the switch away from the column to access the screw holding the instrument panel wire harness connector to the switch.
  8. Disconnect the connector and reverse to install new switch.

Jan 15, 2010 | 1999 Dodge Dakota

1 Answer

1999 dodge durango turn signal problems


check fuse 16 in the fuse panel inside the vehicle...if that fuse has power then likely it is the multifunction switch thats bad or the combination flasher

Nov 13, 2008 | 1999 Dodge Durango

Not finding what you are looking for?
1999 Dodge Dakota Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...