Question about Ford Ranger

Open Question

Replacing heater core in a 2005 ford ranger edge

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76846 Answers

SOURCE: heater core replacement

It's one of the easiest cores to replace that I have encountered. Disconnect heater hoses at firewall. Probably doesn't matter about hose placement, but I always mark them just in case. To remove the fiber cover under dash, take a flat blade screwdriver and pry out the center pin of the expansion clips that hold it in place. There are four 5/16 head screws that hold the bottom/drain tray cover. Core will pull through the firewall and then down. You may have to silicone/glue or replace the foam seal strips on the new core. Before you install the core, check the distance between the inlet and outlet tubes to ensure they match the openings in the firewall. This saves time. It helps if you have someone on the outside to guide you when stabbing the tubes through the firewall. Replace bottom cover. You may have to hold one of the tubes when reinstalling the first hose to the core. Replace any lost coolant and check for leaks prior to reinstalling the fiber cover. If the cover seal is in good condition, any leak should drain through the firewall, otherwise it may leak inside cab. .

Posted on Sep 10, 2008

Ad
  • 69 Answers

SOURCE: Replace heater core in 1988 Ford Ranger

allow the system to cool down

take radiator cap loose to release pressure

once pressure is released tighten cap

loosen clamps on the heater hoses in the engine compartment on the pass. side of firewall.

plug or cap off the heater core tubes to prevent spillage when you pull it into the truck

place a trash bag on floorboard in case spillage occurs

remove the five screws holding the heatre core access cover, three on top and two on bottom

carefully pull heater core back and down and remove it from the dash

install is reverse

Hope this helps

Posted on Mar 29, 2009

localwonder
  • 6784 Answers

SOURCE: 2004 ford ranger edge 3.0L spark plug wire diagram

The diagram you seek is below.


374d96b.jpg

Posted on Jul 26, 2009

  • 7353 Answers

SOURCE: easy way to replace heater core on an 98 ford ranger

the dash must come out.

Posted on Oct 11, 2009

c17hydro
  • 2984 Answers

SOURCE: i need to replace my heater core on my 1995 Ford

Removal & Installation
4274678.gif
Exploded view of the blower motor housing and the heater air plenum assemblies

  1. Disconnect the negative battery cable. Allow the engine to cool down. Drain the cooling system to a level below the heater core fittings on the firewall.
  2. Disconnect the heater hoses from the heater core tubes and plug hoses.
  3. Remove the five nuts that secure the blower motor housing to the firewall.
  4. Pull the housing away from the firewall. Disconnect any wire harness plugs which inhibit the housing.
  5. Remove the remaining nuts which secure the heater air plenum (inside the passenger compartment) to the firewall.
  6. In the passenger compartment, remove the instrument panel. Refer to Section 10.
  7. Pull the heater air plenum rearward from the firewall and remove it from the vehicle.
  8. Remove the heater core from the heater air plenum.
  9. Inspect all air seals on the components and firewall and replace any that are damaged.

  1. To install:
  2. Install the heater core into the air plenum chamber.
  3. Position the heater air plenum against the firewall from the passenger compartment.
  4. Under the hood, install the plenum retaining nuts.
  5. Install the blower motor housing to the firewall and install the attaching nuts.
  6. Connect the heater hoses to the heater core tubes at the dash panel in the engine compartment. Do not over-tighten the hose clamps.
  7. Install the instrument panel.
  8. Check the coolant level and add coolant as required. Connect the negative battery cable.
  9. Start the engine and check the system for coolant leaks.

Posted on Oct 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where would start to repair heater, blowing cool air only. 2004 ford ranger edge


Check that the cooling system is fully serviced (near full mark in coolant reservoir). With engine warmed up, feel (carefully) both heater hoses where they go into the firewall. If both are hot, there is water circulating through the heater core - possibly problem with blend door actuator. If only one hose, or neither hose is hot, you may have a blockage in the heater core. This usually means replacing the heater core, but you may be able to flush it. See this YouTube video: https://www.youtube.com/watch?v=M9SIafVsqyc

Dec 25, 2016 | 2004 Ford Ranger

1 Answer

Changing heater core 94 mazda b2300 2.3


This is a re-badged Ford ranger so watdh the video of rthe ranger heater core change out. How To Replace Heater Core On Ford Ranger

Dec 05, 2016 | Mazda B2300 Cars & Trucks

1 Answer

Can i bypass heater core on a 2001 ford ranger edge 3.0 without bypass controll valve


to by pass a heater core just connect the two hoses to the heater core together with a connector and hose clamps.

Feb 20, 2015 | Ford Ranger Cars & Trucks

1 Answer

2002 Ford Ranger Extended Cab Heater Core Replacement


Not an easy job. Drop the steering column and remove the dash first. Then remove the plenum. Core is between the plenum and fire wall. Get a manual. Your saving hundreds doing it your self. 30 dollars for a manual is worth it.

Jan 26, 2015 | 2002 Ford Ranger

2 Answers

No heat in cab in ford ranger 2005 tied heater


check if both heater hoses going into firewall are hot.. if only one is hot then your heater core is stopped up..you can take both lines loose and take a water hose and back flush,,, force hose on one inlet of heater core for a minute and then the other.. keep going to you get a good flow...make sure heater valve is open, not just valve position take loose and confirm clear..last make sure your thermostat is not stuck open keeping engine from comming up to temperature

Jan 04, 2010 | 2005 Ford Ranger

1 Answer

Heater core removal 98 ford ranger


Disconnect heater hoses. Remove glove box. Remove cover over heater core,has a few 8mm screws. Replace heater core. Reassemble.Good luck.

Nov 04, 2009 | 1999 Ford Ranger SuperCab

1 Answer

Trying to put a heater core in a 1998 ford ranger and don't know how. Do you have a diagram to go by. step by step. thank you.


Disconnect heater hoses. Remove glove box. Remove cover fro heater core (8mm screws) . Remove parts in way of cover. Replace heater core. reassemble. I would recommend flushing system first. Top off coolant.

Oct 04, 2009 | 1998 Ford Ranger SuperCab

1 Answer

Heater core


From Haynes Repair Manual #36071, Ford Ranger Pickups 1993 - 2005: (1)Disarm the airbag system; (2)allow the cooling system to completely cool down; (3)using a thick cloth for protection, turn the radiator filler cap to the first stop; (4)step back and let the pressure release; (5)once the pressure has been released, completely drain the cooling system; (6) working within the engine compartment, loosen the ****,ps on the heater hoses at the engine compartment side of the firewall, twist the hoses and carefully sepseparate them from the heater core tubes; (7)plug or cap the heater core tubes to prevent coolant from spilling into the passenger compartment when the heater core is removed; (8)place a plastic sheet on the floor of the vehicle to prevent stains if the coolant spills; (9)remove the instrument panel; (10)remove the PCM heat sink and ground strap; (11)remove the heater plenum chamber; (12)separate the heater core from the heater plenum chamber; (13)installation is the reverse of the removal with the following additions; (a)fill the cooling system; (b)run the engine, check for leaks and test the heater.

Sep 30, 2009 | 2001 Ford Ranger Regular Cab

1 Answer

Replace heater core in 1988 Ford Ranger


allow the system to cool down

take radiator cap loose to release pressure

once pressure is released tighten cap

loosen clamps on the heater hoses in the engine compartment on the pass. side of firewall.

plug or cap off the heater core tubes to prevent spillage when you pull it into the truck

place a trash bag on floorboard in case spillage occurs

remove the five screws holding the heatre core access cover, three on top and two on bottom

carefully pull heater core back and down and remove it from the dash

install is reverse

Hope this helps

Jan 16, 2009 | 1988 Ford Ranger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...