Question about 2005 GMC Yukon

Open Question

2005 yukon front axle keeps pulling out of housing. Already replaced the spring clip.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

BigBlue77
  • 59 Answers

SOURCE: 2005 Yukon Front Diff Axle seals

You don't have to remove the whole diff to change the seals, but you will have to seperate it where the shaft meets the carrier housing. There is a clip holding the passenger axle shaft in place that you have to remove to change the seal. The drivers side axle stub can be removed with a little force as there is a spring clip holding that side in.

Posted on Sep 06, 2008

  • 61 Answers

SOURCE: how do you remove c clips on rear axle on 2003

You will need to support the vehilce on Jackstands, remover the rear wheels, remove the differential cover. You will see a pin retaining the spider gears in the diff, this pin is held in place with a bolt. Carefully remove this bolt, you may need to spin the carrier to access it, once the bolt is removed (should be an 8mm) you can slide the pin out, and push in on the axles ( you may need to disassemble the brakes to do this) and the c-clips can be removed, and the axles can be pulled from the truck.

Posted on Apr 27, 2010

  • 1796 Answers

SOURCE: I'd like to find out how to replace the front

Hi!!
Check this diagrams, in case you need additional info. just post a comment.
FRONT DRIVE SHAFT K-SERIES c226142.gif
FRONT DRIVE SHAFT V-SERIES e222815.gif

FRONT SUSPENSION DIAGRAM 86c8d3a.gif

INSTALLATION OF DIFFERENTIAL CARRIER ccedc26.gif

INSTALLATION SHAFT SEAL 20c4d08.gif

LEFT SHAFT DIAGRAM b82db9d.gif



Posted on Sep 23, 2010

  • 2427 Answers

SOURCE: Have a 2002 GMC Sierra 1500 4x4 extended cab with

Well actually I don't think the bearing damaged the whole thing, Proberally they just don't want to press and and press out the new bearing cause it may not be worth their time financially.. Tell them just replace the bearing and make sure to grease it properly..

You see they will need to take out the entire assemble, then press out and press in the new bearing as opposed to take out and replace the entire assembly which they can then fix and resell. So just have them change the bearing..

Posted on Nov 01, 2010

  • 1168 Answers

SOURCE: 2004 Yukon XL Denali Frount

Hello akajanke.

If it is the part I am thinking of yes, it is replaceable.
Part #6 below is what it is to verify?

kiltylake_175.gif


Let me know if this isn't correct or if you need more help with this problem.
Thank you for using FixYa.

Kl

Posted on Jan 31, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm looking to replace the rear axle on my 1997 4 door 4x4 GMC Yukon 3.73 gears would a rear axle from a 1998 Yukon 4door 4x4 with 3.73 gears bolt directly to my 1997 Yukon


yes
the housings will be the same
clue here --if the diff center comes into the housing from the front not a problem
if it comes in from the rear ( tin cover removed ) replace the complete housing as you will have to have expertise in resetting the bearing pre-loads for the diff center bearings

Jul 15, 2017 | GMC Cars & Trucks

1 Answer

Is there a c clip in the front driver side holding the half shaft in on a 05 ram 2500 diesel. Trying to replace universal!


There is a spring-type C-clip on the end of the CV housing spline shaft. Disengage the CV joint from the axle housing by using a pry bar between the CV joint and the axle housing. It can be pretty tough to get it to let go. I have found it helpful at times to place the end of a pry bar on the back of the CV housing (as good as I can) and smack it with a BIG hammer. Putting it back in is not nearly as hard.

Jul 09, 2011 | 2005 Dodge Ram 2500 Truck

1 Answer

How does the rear axle come off ? so i can replace the seal and bearing


You will need to pull the rear end cover off,make sure you have a drain pan ready. when you rotaye a rear tire the ring gear will turn,look for a bolt head on the spider gear housing pull out that bolt/pin and then push axle all the way in there will be a c clip on the end of the axle pull that out and remove the axle.Be carefull not to let the spider gears fall out you can put them back but can be a pain.. Hope this helps

Nov 26, 2010 | 1997 GMC Yukon

1 Answer

How do I change the headlight on my 2005 VW Beetle?


There are two spring clips located under the hood around each headlamp housing. Open both clips and extract the headlamp housing from the front of the car by pulling the plastic assembly by grabing the edges by the black rubber seal. The entire headlamp housing will pull out from the front bumper enough to allow you to change the bulbs. Repeat procedure and clip the spring clamps back in place.

Jun 30, 2010 | 2005 Volkswagen New Beetle

1 Answer

2005 single axle F-350


Yes you will need to pull the axle to get that seal out. You will need to pull tire open punkin or gear case there will be a C clip holding the axle inplace pull this out and very carefully slide the axle out the seal is in the axle housing

Apr 08, 2010 | 2005 Ford F 350 Super Duty

1 Answer

How do I remove the rear axles on my 2000 GMC Yukon XL so I can replace the tin brake liners in the wheel hubs?


well you need to pull rear cover and pull rotors or drums off and there are two clips in side the diff but you need to pull the center shaft out AND PUSH THE SHAFT IN WORD AND REMOVE TWO CLIPS AXLE WILL SLIDE OUT

Aug 13, 2009 | 2000 GMC Yukon XL

1 Answer

How to remove rear axels


Welcfome to fixya.Here is the priocedure if you need anything just go to www.collisionrepairadvice.com
  1. Raise and support vehicle. Support at frame behind front springs.
  2. Remove front wheels.
  3. Scribe alignment marks on propeller shaft and axle yoke for proper assembly, then disconnect propeller shaft at axle yoke.
  4. Disconnect connecting rod at steering knuckles.
  5. Disconnect shock absorbers at axle housing.
  6. Remove stabilizer bar connecting links to spring tie plates attaching bolts, if equipped.
  7. Disconnect breather tube at axle housing.
  8. Disconnect stabilizer bar link bolts at spring clips.
  9. Remove disc brake calipers, rotors and brake shields.
  10. Remove U-bolts and tie plates.
  11. Support axle assembly with suitable jack to relieve spring tension.
  12. Loosen rear spring shackle to spring attaching bolts.
  13. Remove front spring shackle to spring attaching bolts and lower spring to floor.
  14. Remove axle from under vehicle.
  15. Reverse procedure to install.

Jul 25, 2009 | 1984 Jeep CJ7

1 Answer

I have a 94 jeep wrangler front left axle seal bad. I took the left side apart and not sure how to get the seal back in. Do I need to open the inspection cover on the diff. and take the gears out?



Rear Axle Notes
  1. Raise and support vehicle.
  2. Remove rear wheels.
  3. Scribe alignment marks on propeller shaft and axle for proper assembly, then disconnect propeller shaft from axle.
  4. Disconnect the track bar from axle mounting bracket.
  5. Disconnect parking brake cable at equalizer.
  6. Disconnect shock absorbers at axle tubes.
  7. Disconnect hydraulic brake hose at rear axle Tee-fitting, then tape ends of hose and fitting to prevent contamination.
  8. Disconnect axle vent tube from axle.
  9. Remove U-bolts and tie plates.
  10. Loosen spring mounting bolts.
  11. If equipped, disconnect ABS wiring connections at axle.
  12. Support axle with suitable jack.
  13. Remove spring-to-shackle attaching bolts and lower spring to the floor.
  14. Remove axle assembly.
  15. Reverse procedure to install.

Front Axle Notes
  1. Raise and support vehicle at frame behind front springs.
  2. Remove front wheels.
  3. Scribe alignment marks on propeller shaft and axle yoke for proper assembly, then disconnect propeller shaft at axle yoke.
  4. Disconnect connecting rod at steering knuckles.
  5. Disconnect shock absorbers at axle housing.
  6. Remove stabilizer bar connecting links to spring tie plates attaching bolts, if equipped.
  7. Disconnect breather tube at axle housing.
  8. Disconnect stabilizer bar link bolts at spring clips.
  9. Remove disc brake calipers, rotors and brake shields.
  10. Remove U-bolts and tie plates.
  11. Support axle assembly with suitable jack to relieve spring tension.
  12. Loosen rear spring shackle to spring attaching bolts.
  13. Remove front spring shackle to spring attaching bolts and lower spring to floor.
  14. Remove axle from under vehicle.
  15. Reverse procedure to install.

Jul 21, 2009 | 1994 Jeep Wrangler

1 Answer

2005 Yukon Front Diff Axle seals


You don't have to remove the whole diff to change the seals, but you will have to seperate it where the shaft meets the carrier housing. There is a clip holding the passenger axle shaft in place that you have to remove to change the seal. The drivers side axle stub can be removed with a little force as there is a spring clip holding that side in.

Sep 01, 2008 | 2003 GMC Yukon

Not finding what you are looking for?
2005 GMC Yukon Logo

Related Topics:

469 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...