Question about 2007 Hyundai Tucson 2.7
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
hi have not had pleasure of this on santa fe yet? but will try to help dependant of which side o/s or n/s ? i would first remove the screws holding the front of the under engine plastic cover/shield and drop down sufficient to gain view/access? to the rear of fog lamp then if a cover is on? try turning anti clock to remove? or if rubber cover pull off? then the bulb and clip should be visible? unplug the wire from bulb then the spring clip holding bulb in place normally just sring the 2x top ends together and swing down/clear to remove bulb? refit new bulb correctly! pay attention to position old bulb positioned? then clip securely and re connect wire at this stage it would be best to ensure bulb works ?? before you re assemble all else? wish you luck and hope this helps with your problem ?
Posted on Oct 28, 2008
You change it like you'd change any headlamp bulb. There is an access cap behind the headlamp assembly -- remove it, then remove the connector to the bulb, then remove the retaining clip/spring holding the bulb in place. Then install/insert the new bulb in the same 'ORIENTATION' as the old one. Reinstall in reverse order... ALAKAZAM!... .done!
Posted on Jun 25, 2009
SOURCE: headlight aiming
on each headlamp assembly, there will be either one or two plastic nuts that you can turn.
If you only have one nut on each, that will adjust the vertical aim of the headlights.
If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.
Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)
If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.
Posted on Sep 14, 2009
there are clips on the side of the bulb holders that squeeze together then push out to reveal the bulb holder. you can locate these by opening the boot lid, and on most mosels removing the plastic surround. you can then see the holders inside. just hold finger and thumb at each end and gently squeeze the clips and push out the holder to replace buls
Posted on Mar 16, 2010
I can't see what you have but lets check a couple of things. If there is any screws visable on the outside of the lens then remove them. Once the cover is off then you should be able to see the bulb. Take the bulb between your thimb and four finger and push in gently and turn to the right and pull out. You would know the rest from there. If no screws outside then lets look in the trunk. You may have to remove some covering in the general area to see the bulb. Follow above directions. If nothing is there then the last place is under the bumper. Have a look and go from there. Let me know I we fixed it. The Raz
Posted on Apr 17, 2010
Tips for a great answer:
May 23, 2015 | 2007 Chevrolet Chevrolet Equinox LT
Nov 03, 2010 | 2007 Hyundai Tucson Limited
Apr 17, 2010 | 2007 Hyundai Sonata Limited Sedan
Mar 12, 2010 | 2007 Hyundai Accent GS Hatchback
Nov 30, 2009 | 2007 Pontiac G6 GT Convertible
Oct 26, 2009 | 2008 Hyundai Accent
Sep 30, 2009 | 2006 Hyundai Sonata
Sep 09, 2009 | 2002 Hyundai Accent
237 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: