Question about Subaru Tribeca

Open Question

Install serpentine belt on a 2007 subaru tribeca

Replaced damaged idler pulley. Can't seem to get the serpentine belt back on.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ewashmidas
  • 362 Answers

SOURCE: Serpentine belt routing

Here you go.. I looked up the same belt you did, it should be right.

adecd3f.png

Posted on Feb 09, 2009

Ad
  • 1 Answer

SOURCE: Serpentine belt doesn't seem to fit

ACTUALLY THERE IS AN UP GRADE THAT ELIMINATES ONE IDLER PULLEY, THAT WILL BE YOUR CASE CHECK ON THE DEALER ABOUT THAT....

Posted on Sep 06, 2008

  • 1 Answer

SOURCE: how do you loosen the serpentine belt

That wasn't right though. There is a 1/2 slot for a 1/2 inch breaker bar and when two holes are lined up you stick a drill bit or similar peice through to lock it in place till you get the belt routed then pull back alittle bit on the breaker bar to remove tension from the drill bit . Remove the drill bit and release tension on breaker bar and remove it to put tension on the belt.Then check alignment , positioning, routing of the belt visually.

Posted on Feb 14, 2009

mrgreenz
  • 962 Answers

SOURCE: serpentine belt slips off idler pulley

The A/C pully is supposed to spin freely until the AC is activated to run.. The cranshaft pully does not. Replace the tensioner pully. The belt has to fit in between the grooves on the pullys.

Posted on Apr 05, 2009

crayzeetrayn
  • 837 Answers

SOURCE: need to install serpentine belt on 2001 Buick Lesabre

There a few different layouts for that car year and model so here is a link and you will find what you need .. Thanks for using FixYa and please rate me a FixYa .. Crayz

Posted on Apr 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

HDo I remove and install an idler pulley on a 2005 Toyota Camry?


How to replace drive belt tensioner Toyota Camry - YouTube

? 4:26
https://www.youtube.com/watch?v=gfSJvN-CE2E
Feb 22, 2013 - Uploaded by Fix It Angel
2002 2003 2004 2005 2006 2007 2008 2009 Toyota Camry. Engine, 4 cylinder, 2.4L, 2AZ-FE. 2004 Toyota ...

Idler Pulley, How to replace (EASY and CHEAP) - YouTube

? 4:56
https://www.youtube.com/watch?v=axAltpW8wR4
Nov 2, 2013 - Uploaded by ChrisFix
Idler pulley squeak? Learn how to fix a squeaky pulley in your car. The serpentine belt in your car powers the ...

2007 Camry Serpentine Belt Replace - 4 Cyl, 2.4 liter ...

? 4:21
https://www.youtube.com/watch?v=ejhyCrh96a8
Jan 13, 2013 - Uploaded by Flyin Brian
I show you step-by step how to get the old belt off and install a new ... ... Water pump replacement 2007 Toyota ...


Jan 27, 2016 | Toyota Cars & Trucks

2 Answers

I just needa serpentine belt diagram for a 2006 subaru tribeca


Diagram reference number 1 in the image below:
7540040.gif"" Fitment: 2006 SUBARU B9 TRIBECA - 4 door

Application Notes:

Category: Electrical. Charging and Starting

SubCategory: Alternator / Generator and Related Components

Position: General

Part Number: 809221090


This is a Serpentine Belt that fits the 2006 SUBARU B9 TRIBECA - 4 door with the EZ30D engine. The Serpentine Belt is designed by SUBARU to be part of the Electrical. Charging and Starting-Alternator / Generator and Related Components. The Serpentine Belt has a position on the vehicle of General. The 2006 SUBARU B9 TRIBECA Serpentine Belt is a factory made SUBARU OEM part and it comes with a 12 month 12.000 mile warranty (parts only). Do not be fooled by an aftermarket SUBARU B9 TRIBECA Serpentine Belt! Buy a factory SUBARU part and receive peace of mind!
This factory part has a part number of 809221090. " clear1x1.gif dbox_border_left_bottom.gif clear1x1.gif dbox_border_right_bottom.gif clear1x1.gif

2_12_2013_10_59_21_pm.gif

Dec 14, 2012 | 2006 Subaru B9 Tribeca

1 Answer

How do you change the serpentine belt


Try downloading the Owner's Manuel online for free. My Buick owners manual has really detailed info on how to put the serpentine belt back on. There are several websites where you can read and or download the owners manual.... Hope this helps!

Jul 13, 2012 | 1993 Buick Park Avenue

1 Answer

Serpentine belt


Application:
With A/C


2.image

Kia_Sedona_2002-2006
Accessory Drive Belts

Print


Accessory Belt Routing



0996b43f802319a9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory serpentine belt routing-3.5L engine


0996b43f802319a9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory serpentine belt routing-3.5L engine


0996b43f8020700d.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory serpentine belt (A) routing-3.8L engine


Inspection

Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.


Removal & Installation

  1. Disconnect the negative battery cable.
  2. Rotate the auto tensioner clockwise to release tension, then remove the drive belt.

To install:
  1. Install drive belt (A). Route the belt over the components in the following order: Crankshaft pulley - A/C pulley - idler pulley - generator pulley - water pump pulley - P/S pump pulley - tensioner pulley.
  2. Rotate auto tensioner arm in the counter-clockwise moving auto tensioner pulley bolt with wrench.
  3. After putting belt on auto tensioner pulley, release the auto tensioner pulley slowly.

    0996b43f802319a9.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Accessory serpentine belt routing-3.5L engine


    0996b43f8020700d.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Accessory serpentine belt (A) routing-3.8L engine


May 09, 2012 | 2006 Kia Sedona 3.8

1 Answer

What does the belt tensioner mount to on a 2006 subaru tribeca?


Go to the dealer parts dept and ask to a see a exploded diagram of the front of the engine and the belt tensioner parts. Ask for a print out of the diagram. You may also find this on line at any site that sells OEM parts.

Feb 21, 2012 | 2006 Subaru B9 Tribeca

1 Answer

How simple is it to change a alternator belt on subaru svx?


  1. Removing the Serpentine Belt
    • 1 Park your Subaru on a level surface and open the hood.
    • 2 Disconnect the ground (black) battery cable using a wrench. This will prevent the cooling fan from activating.
    • 3 Locate the serpentine belt routing diagram in your engine compartment and compare it to the actual routing of the installed belt. Make sure the routing on the label matches the actual routing. If they do not match or there is no label, note the actual routing on a piece of paper for later reference.
    • 4 Locate the belt tensioner pulley on your Subaru model. If the tensioner is equipped with a squared hole, use a large breaker bar with a 1/2-inch (13 mm) drive. Otherwise, use a ratchet and socket of the proper size on the tensioner pulley center bolt.
    • 5 Rotate the tensioner pulley away from the belt to release the belt tension.
    • 6 Pull the belt off of one of the pulleys and slowly release the tensioner pulley back into position. Do not let the tensioner pulley snap back or you may damage an internal component.
    • 7 Finish removing the serpentine belt from the rest of the pulleys and the engine compartment.
    Installing the New Serpentine Belt
    • 1 Match the old belt to the new one and make sure they are of the same length and configuration. It is normal for the new belt to be slightly shorter since the old one has been stretched through use.
    • 2 Route the new serpentine belt through all of the pulleys except the tensioner pulley. Use the diagram on the engine compartment or your notes, as a reference, to properly route the belt.
    • 3 Insert the large breaker bar into the square hole or the ratchet and socket into the tensioner pulley center bolt.
    • 4 Rotate the tensioner pulley in the same direction you did to release the belt tension.
    • 5 Slide the serpentine belt onto the tensioner pulley.
    • 6 Release the tensioner pulley back into position.
    • 7 Look at all the pulleys and make sure the serpentine belt is properly seated on each one. Otherwise, release the belt tension and adjust the belt.
    • 8 Connect the ground (black) battery cable using the wrench.

Oct 18, 2011 | 1992 Subaru SVX

1 Answer

I have a 2000 gmc Jimmy . I'm going to change the


Locate the idler pulley to the left of the crankshaft pulley. The idler pulley bolts to the idler arm. The idler pulley is replaced with the arm because they are sold as one unit.

  • 2 Place a 3/8-inch ratchet driver into the square hole on the face of the idler pulley and pull up on the handle. This releases tension on the Sonoma's serpentine belt. Pull the belt off the idler pulley, lower and remove the ratchet handle.
  • 3 Remove the two bolts that secure the idler arm to the engine block using a socket and ratchet, and discard the old idler arm.
  • 4 Place the new idler arm against the engine block and secure it using the socket and ratchet.
  • 5 Put the ratchet driver into the square hole on the new idler pulley, pull up on the handle and place the serpentine belt over the pulley.
  • 6 Lower and remove the ratchet handle.
  • Oct 15, 2011 | 2000 GMC Jimmy

    1 Answer

    Serpentine belt routing


    Hi,

    The detailed solution provided below will be of great help to you,just follow the steps carefully;

    1.Raise the hood of your Subaru and support it with the prop rod. Locate the negative battery cable at the negative battery terminal. Remove the retaining bolt from the battery cable end with a wrench and separate the cable from the terminal.
    2.
    Find the serpentine belt tensioner on the front of the engine and place a socket on the apex bolt in the center of the idler pulley. Attach a breaker bar to the socket and rotate the tensioner clockwise until the belt is loose, then remove it from the pulleys. Rotate the tensioner back to the home position and let it sit there for now.

    3.
    Install the new serpentine belt over all the pulleys except the tensioner pulley. It is important that the belt follow the correct path over the pulleys. If you are unsure of the path, look for the sticker under the hood with the belt-path diagram on it.

    4.
    Rotate the tensioner clockwise far enough to install the belt around the pulley on the tensioner, then slowly rotate the tensioner back to the home position. The tensioner will tighten the belt correctly and no adjustment is required.

    5.
    Install the negative battery cable back on the negative battery terminal and install the retaining bolt. Tighten the bolt with a wrench, then close the hood.

    Problem solved,

    Good luck!!

    Aug 07, 2010 | 2002 Subaru Outback

    2 Answers

    Belt keeps coming off,already replaced everything,added guards,nothing works,any sugestions?


    My van is doing the same thing I installed the new bracket and it did it again tonight, thats less the 24 hours...

    Feb 15, 2010 | 1998 Dodge Caravan

    1 Answer

    I just replaced the idler pulley. now i'm trying


    on the side...a square hole...use a short socket....ot a pry bar to forse it down...ask autozone.

    Sep 19, 2009 | 1998 Ford Windstar

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    416 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Subaru Experts

    yadayada
    yadayada

    Level 3 Expert

    76649 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8522 Answers

    Are you a Subaru Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...