Question about 1997 Jeep Grand Cherokee

Open Question

Replace idler pulley for 1997 jeep grand cherokee 5.2

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 1996 jeep grand cherokee limited v8

I might not have enough information but the squeal is most likely a worn bearing. Try to isolate it with a "mechanic's stethescope" to locate the source. A pin point shot of WD-40 at the whining bearing (NO NOT put it on good bearings should TEMPORARILY quiet it IF it is a bearing. DO NOT overspray, just at the center of the pulleys...the lubricant should get pulled into bearing to confirm that the pump (power steering would be my guess) needs replacing.

Posted on Jan 09, 2009

  • 10 Answers

SOURCE: location of crankshaft position sensor Jeep grand cherokee 1997

left rear of engine block,on transmission bell housing.best way from top under brake booster use a wrench,

Posted on Jun 13, 2009

  • 58 Answers

SOURCE: replace fuel filter on 1997 jeep grand cherokee

If you have the V8 engine, the filter is actually part of the fuel pump. WHICH IS IN THE TANK

Posted on Jun 28, 2009

  • 132 Answers

SOURCE: How do I replace the Idler Pulley on my 1994 Jeep

Should only be one bolt going thru the center of the pulley. probably a 14 or 15mm size.

Posted on Jan 08, 2010

rogrrabbit
  • 986 Answers

SOURCE: HOW DO YOU CHANGE THE IDLER PULLEY?

It is as simple as removing the nut and pulling it off and sliding the new one on. Once you get it back replace the belt and set it to the correct tension. It is as simple as that. Without a belt tension gauge a good rule of thumb is about 1 inch of deflection at the longest belt run.
On your engine it's 1 inch between the power steering pump and the air conditioner compressor.

-->

Posted on May 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Squeal while accellerating in 1995 jeep grand cherokee


The idler pulleys on the Cherokees are known to squeal and make noises when their bearings are bad. They are also known to eventually break off and disable the vehicle, if not replaced when they're bad.

Oct 03, 2011 | 1995 Jeep Grand Cherokee

2 Answers

What size bolt is it for the idler pulley for 1997 jeep grand cherokee larado?


Should only be one bolt going thru the center of the pulley. probably a 14 or 15mm size.


Dec 20, 2010 | 1997 Jeep Grand Cherokee

1 Answer

Drive belt popping off


I'm assuming you mean your serpentine belt. You most likely have a worn bearing on your idler pulley and/or tensioner pulley. Given the low price of these pulleys and the possible cost of repairing the possible damage when this belt comes off I would recommend replacing both.

Jun 07, 2010 | 1997 Jeep Grand Cherokee

1 Answer

How do I replace the Idler Pulley on my 1994 Jeep Grand Cherokee?


Should only be one bolt going thru the center of the pulley. probably a 14 or 15mm size.

Jan 04, 2010 | 1994 Jeep Grand Cherokee

1 Answer

Serpentine belt diagram for 2000 jeep grand cherokee 6 cylinder


Around the outside of power steering pulley,under idler,over a/c comp,around alternator,over fan pulley, around crank pulley, over water pump. The backside of the belt contacts the idler, fan and water pump.

Sep 28, 2009 | 2000 Jeep Grand Cherokee

1 Answer

2000 jeep grand cherokee 4.0 liter engine timing belt replacement


If you have the same pulley arrangement that most 4.0 engines have that pulley is an idler not a tensioner. Your power steering pump has a pivot bolt, and a slide under the pump. You adjust belt tension using the pump.

Apr 04, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
1997 Jeep Grand Cherokee Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...