Question about 2006 Chevrolet Impala

Open Question

2006 chevy impala ss random misfire spark plug 7

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 20 Answers

SOURCE: electrical problems with 2006 impala ss

replace... probably a dead cell

Posted on Jun 30, 2008

Ad
DAD5bbbbg
  • 111 Answers

SOURCE: 2003 CHEVY IMPALA/ REAR SPARK PLUG REMOVAL

It makes it a lot easier if you move the alternator out of the way. some times you can get to them from the bottom of the car. When you get to the plug wires twist them to get them lose from the spark plug. Make sure you grab the end of them. don't twist just the wire.

Posted on Apr 01, 2009

emissionwiz
  • 76649 Answers

SOURCE: How do I program my key for my 2006 Chevy Impala?

Add Duplicate Key (PK3 or PK3+ key)
1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.
Originate New Master Key (PK3 or PK3+ key)

1. Insert new key into ignition cylinder and turn it to the ON (RUN) position.
The security light on the dash will illuminate and stay on for ten minutes.
2. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back to the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
3. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back on the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
4. After the security light has gone off the third time, the key has been programmed
into the vehicle’s computer and will operate the car. It has replaced ALL the
previous electronic key codes and is the ONLY key programmed into the
vehicle’s computer.

Add Duplicate Key (PK3 or PK3+ key)

1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.

Posted on May 20, 2009

motor1258
  • 6674 Answers

SOURCE: 2006 Chevy Impala reduced engine power

best bet is to stop in at a Pep Boys, Autozone, or similar big autoparts seller, and ask for free trouble code scan, which should pinpoint area causing problem. If not obvious by codes, what is necessary to repair the problem code, get back to us with those codes and we will be glad to assist you further. Better this way, takes away the guess work, and saves you money, as well as getting it right the first time.

Posted on Dec 12, 2009

  • 3 Answers

SOURCE: 2.2 ecotec engine. Code says random misfire. What

did you fix it? if you did what did you do? i have the same prblm thanks!

Posted on Jan 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Got a p.o.300 misfiring. Had disconnected wire's from distributor and lost track. Need a diagram of correct placement.


google the engine make for the firing order
p0300 is random misfires and is seldom plugs and wires but more likely to be low fuel pressure ( dirty filter) or blocked injectors

Oct 15, 2017 | Cars & Trucks

1 Answer

2006 chevy impala ss horn relay location


Horn relay is located under the hood in power distribution centre

Jan 22, 2015 | 2006 Chevrolet Impala SS

1 Answer

What can cause a cylinder 1 misfire in a 2003 Chevy impala with a 3.4 liter engine


Misfire reasons.
Bad ignition coil (there are 3 of them), bad spark plug, bad spark plug wire (most common) defective fuel injector, intake manifold vacuum leak, low cylinder pressure due to burnt valves or scored cylinder walls.

Sep 25, 2011 | 2003 Chevrolet Impala

1 Answer

P0300 random misfire chevy 2002 impala


depending on mileage, but possible tune-up could fix it. if already done then check ignition coil pack and ignition wires also spark plugs, check vacuum hoses for leaks or porous, last injectors clogged - use some techron fuel injector cleaner (wal-mart has them). have worked at G.M. dealership for over 15 years, saw that alot.

Feb 12, 2011 | 2002 Chevrolet Impala

1 Answer

I replaced the coil blocks, wires, and plugs on my 2005 chevy impala 3.4. I am still getting random misfireing, what else can it be?


could be a fuel problem or a fuel injector. these engines are also bad to leak water at the intake manifold gaskets, if coolant leaks internally it would kill the spark and cause a misfire. if its not low on coolant though i'd keep checking fuel and fire

Oct 24, 2009 | 2005 Chevrolet Impala

Not finding what you are looking for?
2006 Chevrolet Impala Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...