Question about 1999 Chevrolet Monte Carlo

Open Question

What size wrenches do i need to change the fuel filter

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 14585 Answers

SOURCE: What size tube wrench do

!6 mm on the fuel line and 20mm on the filter.

Posted on Jul 01, 2011

ranunyenye26
  • 241 Answers

SOURCE: I have a 97 Chevy Tahoe 4x4 350 vortech, what

it just a basic tools. find the filter and see what size it is.
crawl under the truck on the driver's side, follow the fuel line from the fuel tank to the filter(shape:cylindrical).
make sure the line has no pressure. you should pull the fuse for the "fuel pump" relay, then start the engine and allow it to stall.

Posted on Mar 02, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is fuel pump located on a 1985 chevy cavalier?


The pump is electric, and it is inside the gas tank. You have to drop and remove the tank to change the pump.
The filter is a small metal cylinder, about fist size, and will be in the fuel line under one side or another of the car, unless it is in the engine bay, just before the fuel line reaches the engine. I expect it would however be underneath, along a frame rail. Just follow the fuel line from the tank. Both ends of the filter are threaded. Use 2 wrenches, one as a back-up while you loosen the fuel line fitting. Be careful of damaging the end of the fuel line-that is why you want 2 wrenches.

Nov 23, 2015 | Cars & Trucks

2 Answers

How do i change a fuel filter on this model


the fuel filter is located under the car along the frame once found the inlet side has a plastic line and clip push line towards filter and then depress sides of clip and slowly pull off filter gas will leak out of filter and line then remove filter from mounting bracket and loosen the hex line with a flare wrench 16mm if OE filter the nut size on filter is 20mm some replacements are 19mm but you can hold this with a crescent wrench spin out and remove line reassembly start and run car and check for leaks.

May 11, 2014 | 2002 Cadillac Deville

1 Answer

How to change fuel filter on n1999volvo 2.4 turbo


They are slip on/off. You use an 17mm size box wrench and wedge it between the end of the hoses and the fuel filter and GENTLY pry the hoses off. After securing the new filter in place, push the hoses back on by HAND. Note the flow direction on the filter (there is an arrow on the body of the filter) before removing and make sure it is facing the same direction when re-installing.

Apr 27, 2014 | 1999 Volvo V70

1 Answer

Fuel filter


The new filter is cheap and a vary good idea to replace 5 or 6 years it will save the intank pump from working way to hard to pump fuel to the intake manifold injection system . Alot of fuel pumps go bad because the inline filter is restrected . The filter is located under the drivers door on the inside of the frame rail close to the floor board look for the fuel line that comes from the tank pump and the line that goes up to the engine compartment area so it will have a metal line on bolth sides of it that has a connecter . What you need is open end wrenches or flare nut wrenches just make sure they are the correct sizes . You need to lossen these connections . The filter has a welded nut on it the line has a compresstion fitting that is part of the line and smaller then the welded nut on the filter but will not slide off the line because the line is flared so it will seal againest the filter . I would recomend getting the new filter first note the arrow on it this is the derrection the fuel must flow from the tank to the engine the arrow points to the engine and you can also know what size the welded nuts on the filter are also you can see what you are looking for under the vehicle . The fuel line nut is likely 5/8 s but may be metric 14 or 15 mm . The problem is you will not have a lot of room to work the filter is mounted to the frame with a strap type fastener and can be removed but if you can lossen the fittings with out removeing this first it will be easyer . Wonce the fittings are lose you will need to lossen or remove this strap to slide the new filter in place . And be ready for gas to leak out you will get 6 or so ounces of fuel that will spill on you and the ground . I hope i didn't make sound hard to do .The hardest part is breaking the lines free so make sure you have the right size wrenches and the limited room to get at the fittings GOOD LUCK

Mar 09, 2012 | 2002 Pontiac Montana

1 Answer

What tools do i need to change a inline fuel filter


If it is a plastic type, with rubber hose connections, then just a pair of pliers to remove the squeeze clips.

Nowadays most EFI cars have a metal body fuel filter with a "banjo" connection at one end. For this you need a socket wrench or ring spanner the right size.

At the other end is probably a metal fuel line with a compression fitting nut on it, which may be very tight. Here you need a flare nut wrench, which is a ring spanner with a slot to allow it go around the fuel line. Using an open end spanner or adjustable spanner may round off the nut if it is tight.

Nov 19, 2011 | Cars & Trucks

2 Answers

I need instructions on how to replace the fuel filter on a 1982 Chevy Impala (V8 267 engine). Also need to locate the fuel filter.


the fuel filter is located in the carburetor.were the fuel line attaches to the carb this is were the filter is located.you need a 7/8"wrench and a 1" wrench.put the 7/8" on the fitting of the fuel line and the 1" on the fitting on the carb.undo the line and move out of way then using the 1"wrench remove the fitting on the carb and the filter will come out with it.there is a spring that will push the filter out a bit.leave the spring in and install the new filter with the end of the filter that has no hole(solid end) into the carb and the end with the hole(rubber pulse dampner) facing the fuel line.re-assemble in reverse order,start car check for fuel leak and your done.

Apr 25, 2011 | Chevrolet Impala Cars & Trucks

1 Answer

Process for installing fuel filter


Hello Friend:

#1) Open Hood and Locate the Steel Fuel Line running to the carburetor.

#2) You'll need to use 2-Different Sized Wrenches to Break the Steel line with-Out twisting it.

#3) You'll see a Smaller Nut should be 1/2 -3/4 Inch.If you have recommend using a Flare wrench on that Nut.

#4) Then you'll need a Larger Wrench to Back up the Flare Wrench,Its a Brass Larger Nut Right on the Carb.Even a Cresent Wrench will work.On the big nut on Carb.

#5) Holding the Lager Wrench at the same position its in,don't let it Move,while Loosening the Nut on the Line.Remove the line away from the Larger Brass nut on Carb.

NOTE: Lossen your gas Cap to Relief any pressure in your Fuel Lines. Put some old Rags or something right under the Connection to catch the Fuel that will come out after the Line is broken

#6) now go ahead and Turning it counter clockwise take the Inlet Brass Nut on Off. After its Removed the Fuel Filter is inside a Cavity made just for the Fuel Filter.

#7) On the Brass Nut theres a Gasket besure not to loose or damage it you'll need it to seal the Fuel filter from any Leaks.

#8) Also the Fuel Filter is different on both ends.So watch carefuly how it comes out so you get it in the Direction of Fuel Flow the correct way.

#9) Sometimes People add a inline Filter as well some where in the Fuel line Coming out of the Carb. if there is I recommend you also change it.

To install your new Fuel Filter or Filters Simply Reverse the Procedure that you used to remove the Filter.

I hope this will help you Please let me Know by oting for the Quality of my solution.And a Testamony would be Appreciated.

Thank You for using FixYa From: d_hubbs

Aug 09, 2010 | 1984 Chevrolet C1500

1 Answer

What do I need to do an oil change on a 2003 gmc envoy?


1. Ramps or jackstands (do not do this with only a jack)
2. Appropriate wrench to fit the drain plug
3. Filter wrench for your filter size (when you buy the filter you can decide which size you need - there are 2 sizes)
4. Drain Pan
5. Oil filter and Appropriate amount of oil (recc - 10W30)
6. Creeper for comfort if you prefer
7. A bundle of rags

Jan 14, 2010 | 2003 GMC Envoy

4 Answers

Fuel filter


unbolt the filter from the bracket, that is a 5/16" machine screw head size, then remove the nylon clips that hold the lines onto the filter, hold a rag over the fuel line when u remove it, it will have about 30 pounds of pressure.

May 09, 2009 | Ford F-150 Cars & Trucks

2 Answers

Oil change specs


the engine takes 4qts w/filter and the drain plug is 17mm.

Apr 12, 2009 | 2001 Hyundai Elantra

Not finding what you are looking for?
1999 Chevrolet Monte Carlo Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...