Question about 2007 Pontiac Vibe
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
notorious done if before, remove the door panel. BE CAREFUL WITH BEAUTY CAPS, CAN BE EASILY BROKEN (PLASTIC) when you remove the door panel go ahead and closed the driver door and activate the door lock button. you will see the bracket is either loose or it off. it looks the a coat hanger when you stretch it out. Reconnect it and lithium grease, test it and its a wrap.
Posted on Dec 26, 2008
I found this on another page, hope it helps:)
Remove the plastic cover behind the door handle assembly by removing one black 14mm nut from just above the door handle, and 1 screw (usually phillips) from the bottom of the plastic cover.
Remove linkages from lock cylinder and door handle assembly. Use a small flathead screwdriver to slide retaining clips forward, and linkages will come free.
Remove one black 14mm nut from the very top of the door handle assembly.
Remove one phillips screw drom the bottom of the door handle assembly.
Door handle assembly should now come free by pulling out slightly at the top, and pulling upwards.
Transfer lock cylinder and key minder light (if applicable) to new door handle assembly. Lock cylinder is retained by a single TORX bolt.
Reinstall in reverse.
TIP: If you lose or damage any of those black plastic coated nuts, order new ones. They are GM p/n 10067214 and should be around $0.58/each. There are two on each door.
Posted on Apr 03, 2009
On the 2004 Pontiac Vibe that I owned, I ended up taking it to the dealer. Perhaps this advice can avoid having you end up at the same place!
Remove the middle environmental control knob (fan blower speed, I think) by tugging on it until it comes off. Underneath you will find a single Phillips screw. Remove the screw and gently (so you don't mar it), pull at the plastic trim surrounding the environmental control area. It should pop out. You may also want to remove the two-prong AC outlet by prying it gently out with a small slotted screwdriver before attempting to pry out the trim panel.
After that panel is out of the way, you are ready to tackle the plastic trim surrounding the shift knob. Begin by removing the small holding compartment at the base of the shift knob. There is a single Philips screw holding the plastic piece to a supporting brace on the lower end. Four additional screws on the upper end are revealed by the removal of the environmental control trim piece as previously described.
Okay, from there, you're ready to gently pry loose the trim panel surrounding the shift knob.
The bulb can be located on the driver's side. It's a 'funny' looking bulb that is integrated into a two wire bundle. You may end up having to replace the bulb+wire bundle as a unit. The electrical connector is on the opposite side of the shift knob.
Posted on Feb 25, 2010
SOURCE: I am looking for molded
Please see links below of a few online stores. Let me know if this helps. Thank you.
Posted on May 29, 2011
Tips for a great answer:
Jun 27, 2016 | 2003 Pontiac Vibe
Apr 29, 2015 | 2002 Buick Rendezvous
Mar 08, 2015 | 2006 Pontiac Vibe
Jul 17, 2014 | 2008 Pontiac Vibe
Mar 25, 2013 | 2000 Pontiac Montana
Apr 15, 2012 | 2007 Pontiac Vibe
May 22, 2017 | 2007 Pontiac Vibe
Dec 26, 2008 | 2004 Pontiac Vibe
Oct 16, 2008 | 2001 Nissan Quest
Aug 04, 2008 | 2004 Pontiac Vibe
302 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: