Question about Peugeot Cars & Trucks

Open Question

How to remove and realigne rear wiper arm on pug 307 sw

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: How do I remove the rear wiper arm on my 1996 Ford Explorer?

Pull the wiper arm away from the glass until it is straight out. Then take a small flat blade screw driver and release the retaining clip at the base of the pivot arm. The carefully pry the pivot arm from the shaft.

Posted on Apr 15, 2009

Ad
  • 3600 Answers

SOURCE: removal of broken rear wiper arm. removed nut but

After removing the nut turn the arm up and wiggle it back and forth while pulling it will come off.

Posted on Oct 11, 2009

Testimonial: "Thank you for the advice. You saved me labor cost at the dealer and waiting around for the repair."

  • 151 Answers

SOURCE: Can't remove rear wiper to replace on 96 caravan

Lift wiper arm from rear window. then release latch that holds the blade to the wiper arm.( It's small tab)

Posted on Jan 27, 2010

kennyz195
  • 61 Answers

SOURCE: replace rear wiper arm

there is a cover at the base lift it up and then you have a nut. 10mm remove this and pull off the arm. sometime they get stuck and you will have to pry it up.

Posted on Apr 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Peugeot 307 est. rear wiper removal


get a new 1 or check the breakers yards

Aug 26, 2014 | Peugeot Cars & Trucks

1 Answer

02 liberty rear wiper dose not work plugin has power changed wiper motor still doses work


There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.

zjlimited_494.gif

1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..

zjlimited_495.gif

1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

Jul 19, 2011 | 2002 Jeep Liberty

2 Answers

How do I fix or replace the rear wiper motor


Hello,

  1. Disconnect the cable running to the negative terminal on the car's battery. To do this, loosen the nut on the cable clamp until the clamp is loose enough for you to slide the cable clamp off the negative battery terminal.
  2. Pull the wiper arm away from the rear windshield until the wiper arm locks into a vertical or semi-vertical position or is perpendicular to the rear windshield.
  3. Remove the nut holding the wiper arm assembly to the rear wiper motor.
  4. Pull the wiper arm off the wiper motor assembly.
  5. Unplug the rear wiper motor plug/harness.
  6. Remove the screws holding the rear wiper motor to the inside of the vehicle at the base of the rear window.
  7. Pull the rear wiper motor off.
  8. Install the new wiper motor and put the wiper motor and arm assembly back on the vehicle by reversing the completed steps.
From ehow.com

I hope this helps

Mar 21, 2011 | 2000 Ford Expedition

3 Answers

The wipers are stuck in the up position when they are turned off. the work ok but will not nest when turned off


This is a very common problem on the Impalas. I had to fix my 2002 Impala. The wipers will point straight up.
There is a tab that may be bent near the wiper motor shaft.
Open the hood.
You need to remove the driver's side wiper arm. You need to pop-off the round black cover and there's a nut underneath.
Then remove the plastic cover between the windshield and the engine compartment.
See the pictures below, Look for a bent TAB. it's tough, but bend it back with pliers and/or big screwdriver.
If the tab is OK, look for a missing or broken spring. For that, you'll need to get the replacement part from the dealer. May be: park mechanism, part #12494832
zeevert_22.jpg
zeevert_23.jpg
zeevert_24.jpg
I did a full write-up at this website: www.naioa.com
http://www.naioa.com/v2/modules.php?name=Forums&file=viewtopic&t=26086
You may have to register for free, and look under the "knowledge Based" section in the Forum.

Dec 09, 2010 | 2002 Chevrolet Impala

1 Answer

I installed a new wiper motor. I ran it before installing the wiper arms. it will not stop at zero. it over travels down into the cowling. I try to rest them higher then they stop some where in the middle...


Try to run the motor without the wiper arms tightened down and turn it off so it can cycle down to its rest state. Then install the wiper arms.

Make sure, that the car's windshield wiper wiring is correct for this motor.
---
Wiper Arm & Blade Removal & Installation Front To Remove:
CAUTION
When the wipers are parked (off), the driver’s wiper arm must be above the passenger’s wiper arm.
  1. Remove the clip holding the outside end of the wiper arm cover to the arm.
  2. Lift the arm cap up to expose the nut.
  3. Remove the wiper arm mounting nut.
  4. Using a suitable two jaw puller, remove the wiper arm from the wiper pivot.
To Install:
  1. Verify that the wiper motor and linkage are in the parked position.
  2. Place the wiper arm in position over the wiper pivot.
  3. Install the nut to hold the wiper arm to the wiper pivot. Torque nut to 26 ft. lbs. (35 Nm). CAUTION
    Make sure to tighten the wiper arm nut properly.
  4. Push the arm cap cover down.
  5. Secure the clip holding the cover to the wiper arm.
Rear To Remove:
  1. Lift and hold the wiper arm away from the rear window.
  2. Lift the lock securing the wiper arm to the pivot.
  3. Slowly release the wiper arm so it rests against the lock.
  4. Remove the wiper arm from the pivot.
To Install:
  1. Install the wiper arm on the pivot.
  2. Pull the arm outward and release the lock.
  3. Gently release the wiper arm until it rests on the rear window.
prev.gif next.gif

Aug 22, 2010 | 1996 Dodge Grand Caravan

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

1 Answer

How do you adjust the windshield wiper arms on a dodge grand caravan


There are no adjustments on the wipers. The arms come off to realign. Pop the wiper arm cap off with a very small flathead screwdriver theres a liitle opening slot to do this. Remove the nut. Pull wiper off straight, use pulley if needed. If the tenson is gone in the wiper arm replace. The springs go bad in the rear arm from dirt.

Dec 02, 2009 | 2005 Dodge Caravan

4 Answers

2000 Saturn LS, windshield wipers park in the middle of the windshield. How can I fix this?


The wipers are parking in the middle because the timing mechanism is off. Once they start doing this it seems to continue to happen so the 1st suggestion is to replace the wiper motor. If U don't want to spend the $ right now it's a pretty easy fix to reset the timing. Park the wipers & remove the wiper arms. Then remove the plastic cowling that covers the wiper motor & the motor assembly. Turn the wiper assembly over without turning the motor. Remove the nut on the arm of the motor. Repostion the arm pointing away from the closet wiper directly inline with the short arm. reassemble.

Oct 24, 2009 | 2000 Saturn Ls 4dr Sedan

1 Answer

How to remove the rear window wiper on a 1997 wagon


First do not pry on it, you will crack the rear windshield and have a bigger problem. In addition to the little slider lock at the base of the shaft mostly likely the wiper arm is corroded onto the motor/transmission shaft. What I have done successfully is carefully hack saw off the top of the wiper arm over the shaft. The top of the shaft is then exposed, soak it over and over with a penetrant, put a gear puller onto it and pull it off. A new shaft is about $45.00 at saturnparts.net which may be cheaper than a dealer. A dealer mechanic tells me what he does is drill a hole down through the top of the shaft, squirt a bunch of W40 down into the hole, then drive a metal screw into the hole which pops the arm off. In either event the old shaft is worthless. If your motor works count yourself among the lucky, note that most car parts stores will tell you that one wiper motor fits the rear of saturn SW from 94-99, that is not true. Take your old motor in with you to make sure they sell you the right one.

Oct 22, 2009 | 1997 Saturn SL

1 Answer

HOW DO I REPLACE A REAR WINDOW WIPER ON 2005 FORD ESCAPE?


Remove the rear pivot arm.
Lift the pivot arm to the upright position.
Slide the locking tab out.
Pull up and remove the pivot arm.
Remove the rear wiper motor shaft nut cover.
Remove the rear wiper motor shaft nut.
Remove the rear wiper motor cover.
Remove the rear wiper motor bracket nut.
Remove the bolt and the rear wiper motor.

Jan 29, 2009 | 2005 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

712 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

mike hayward

Level 2 Expert

279 Answers

lloyd cole

Level 2 Expert

250 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...