Question about 1990 Buick Regal

1 Answer

Where do plug wires go on distributor - 1990 Buick Regal

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,101 Answers

What make and model and year

Posted on Dec 03, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

No spark on the plugs of 318(m40)


you don`t say what year this is so I will guess this has a distributor, check for power at the ignition coil and coming out of the coil on the wires. then check for spark coming out of the coil. check the distributor cap and rotor for cracks and burn areas that will allow the spark to go to ground and not the plugs.

Aug 21, 2014 | Cars & Trucks

1 Answer

Spark plug wiring from distributor cap to spark plugs on a 95 honda civic dx 1.5 liter 16 valve sohc


If you look at the distributor cap from the wires side carefully, you would find either a line mark on one of the outer side of four holes (where the spark plug wires are inserted) or the numbers printed on the top of distributor cap (1,3,4,2). Fix one end of the longest high tension plug wire into number 1 hole or the one marked with a line mark on the distributor cap and the other end on spark plug number 1 (the number 1 plug is toward the pulleys and the belts side, then No 2, No 3 and No 4). While standing in front of right wheel you will see the distributor cap in front of you. The rotor moves clock wise. After you fix the 1st cord, next comes number 3 plug wire. Insert one end of the cord into the next to 1 on the right hand side and press the other side of the cord on spark plug number 3. Next to 3 is the cord number 4 and the last one is number 2.

Mar 22, 2013 | Honda Civic Cars & Trucks

2 Answers

What are the to coil packs on a set of spark plug wires on a 2001 4.3 chev blazer for and what plugs do they go on


Your Coil Pack Is Separate And Plugs Into The Middle Of Distributor Cap.Follow The Middle Wire To Coil Should Be On Passenger Side
Easy Quick Change Out. Cost Is Around $40

Mar 11, 2013 | 2000 Chevrolet Blazer

1 Answer

I need the diagram for plug wiring for 1992 ford tempo


Firing order is 1-3-4-2 Please rate if this helps

Installation of wires
  1. Whenever a high tension wire is removed for any reason from a spark plug, coil or distributor cap, or a new high tension wire is installed, Silicone Dielectric Compound WA-10, D7AZ-19A331-A (ESE-M1C171-A) or equivalent must be applied to boot before it is reconnected. Using a small clean tool, coat entire interior surface of boot with Silicone Dielectric Compound WA-10, D7AZ-19A331-A (ESE-M1C171-A) or equivalent.
  1. Insert each wire on proper terminal of distributor cap. Ensure wires are all the way down over their terminals. The No. 1 terminal is identified on cap. Install wires starting with No. 1 terminal.
  1. Remove wire retaining brackets from old high tension wire set and install them on new set in same relative position. Install wires in brackets on valve rocker arm covers.
  1. Connect wires to proper spark plugs.
  1. Install coil wire.


Installation of distributor
Before installing distributor, visually inspect distributor. Inspect O-ring. It should fit tightly and be free of cuts. The drive gear should be free of nicks, cracks and excessive wear. Rotate distributor drive shaft. It should move freely, without binding.
  1. To install distributor correctly, No. 1 piston must be at Top Dead Center (TDC) of compression stroke. Remove No. 1 cylinder spark plug and rotate engine clockwise until No. 1 piston is on the compression stroke.
  1. With No. 1 piston on compression stroke, align timing pointer with TDC on the crankshaft damper.
  1. Align locating boss on rotor with hole on armature. Fully seat rotor on distributor shaft.
  1. Rotate distributor shaft so blade on rotor is pointing toward mark on distributor base, that was previously made in Step 2 of the Removal procedure.
  1. While installing distributor, continue rotating rotor slightly so leading edge of the vane is centered in vane switch stator assembly.
  1. Rotate distributor in block to align leading edge of vane and vane switch stator assembly. Verify rotor is pointing at No. 1 mark on distributor base. If vane and vane switch stator cannot be aligned by rotating distributor in cylinder block, remove distributor enough to just disengage distributor gear from camshaft gear. Rotate rotor enough to engage distributor gear on another tooth of camshaft gear. Repeat Step 1 if necessary.
  1. Install distributor hold-down clamp and bolt. Tighten bolt, but leave it loose enough to rotate distributor.
  1. Install distributor cap, No. 1 spark plug and ignition wires. Check that ignition wires are securely connected to the cap and spark plugs. Tighten distributor cap hold-down screws to 2.0-2.6 Nm (18-23 lb-in).
  1. Reconnect distributor to wiring harness.
  1. Set initial timing according to procedures found in Section 13A of the Powertrain Control/Emissions Diagnosis Manual .
  1. After timing is set, tighten distributor hold-down bolts to 23-34 Nm (17-25 lb-ft).
  1. Recheck initial timing. Adjust if necessary.

Oct 11, 2011 | 1992 Ford Tempo

2 Answers

Not sure how to replce spark plug wires from the distributor need help please send info


change one spark wire at a time on the distributor.buy new set of spark plugs wires remove them from box.match old wires with new wires to use the correct length to each cylinder.now if you need to change distributor cap.mark location distributor cap.number tag plug wires on the distributor cap so you can remove plug wires on distributor cap so you can replace cap and rotor and put wires back on the distributor cap in correct place.remember change one plug wire at a time so you wont get confuse.

Apr 15, 2011 | 1992 Ford Tempo

1 Answer

I need to replace ,the rotor button...


TAG OR NUMBER ALL SPARK PLUG WIRES ON THE DISTRIBUTOR CAP BEFORE REMOVING CAP. SO YOU CAN PUT PLUGS WIRES BACK IN THE ORIGINAL POSITION. WHEN ALL PLUGS WIRES ON DISTRIBUTOR CAP BEEN NUMBER.REMOVE ALL PLUG WIRES ON CAP.THEN REMOVE THE DISTRIBUTOR CAP.THEN MARK ROTOR POSITION WITH SHARPIE MARKER THEN REMOVE THE ROTOR.

Mar 02, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

Dual distributor spark plug wiring diagram for model building.


You are correct in your idea about how the plug wires are attached. If you want to duplicate control wiring you would need to obtain the wiring diagram of the brand of ignition system you want to duplicate. (MSD etc. These systems also require a small battery in order for them to operate. Wiring to distributor was far less complex when vertex type magneto distributors sere used as all that was required was a ground wire to shut them down (exactly like your lawnmower works), As far as plumbing, all systems need to meet safety standards set forth by the NHRA but aside from meeting those standards, each engine builder decides where to locate such items as primary and secondary fuel injectors etc. If you go to the NHRA website, you may be able to find a decent photo of someones engine...that may be helpful. Also check the rule book for such items as kill switch location, brake, chute release etc.

Sep 12, 2009 | 1998 Pontiac Trans

2 Answers

1987 GMC Jimmy Distributor cap and Rotor replacement


A diagram may not be needed as its a reasonably easy fix to do on your own.the distributor ca p will only fit on properly one way because at the base of the cap locaters can only fit the distributor if they line up.When doing the spark plug leads do them one at a time and if nessecary write or mark leads as 1,2 etc .The rotor can only fit on one way but put a mark on the distributor to show where the rotor was pointing when you took it off and if it still points there when the new one is fitted.When changing distributor cap and leads they have to go to the correct place.Pays to mark the outside of distributor cap where the locating bits are On the new and old one.Fit the new cap and rotor then take a spark plug lead and fit to new cap 1 at a time.You can tell by lining up the marks on the outside of the distributor cap when you hold them one on top of the other.Good luck

Oct 20, 2008 | 1987 GMC Jimmy

Not finding what you are looking for?
1990 Buick Regal Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...