Question about 1998 Isuzu Rodeo

Open Question

.ABS light stays on in my 1998 Isuzu Rodeo

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Isuzu Rodeo abs light

I had it repaired: one of my sensors needed to be replaced. No more light!

Posted on Nov 23, 2008

  • 4 Answers

SOURCE: timing settings for a 1998 isuzu rodeo

You didn't say whether you had a V6 engine or a 4cyl. Here is the procedure for a V6.

It sounds like he moved the cam shaft independently of the crankshaft or other camshaft so you will need to do all these procedures:

1. Turn the crankshaft until the mark on the spocket is lined up with the mark on the oil pump housing (the mark is on the driver's side at 90 degrees to the sprocket itself).

2. Back off the crankshaft counterclockwise 1/8 turn to ensure the pistons aren't at top dead center. This gives the valves room to move without hitting the piston.

3. Turn the passenger's side camshaft until it "jumps" into place with the alignment mark on the camshaft pully is pretty close to being lined up with the mark on the engine head.

4. Turn the driver's side camshaft until it "jumps" into place but this won't be perfectly lined up with the mark but will be about an 1/8 turn off from the mark. Then line it up by hand.

5. The idler pulleys and tensioner pulleys should be installed on the engine but the tenioner pulley adjuster (it is a little cylinder with a rod coming out of it that is held in place by 2 bolts) should be removed.

6. Place the new belt on the crankshaft first. Be sure the arrows on the belt point in a clockwise direction. If you have a belt with lines and dots then the lines will line up with all markings that you have lined up together. The dots should line up at the 270 degree point on the crankshaft (opposite of the lines and the markings).

7. Loop the belt around the tensioner pulley, around the passenger's side cam, under the waterpump, around the driver's side cam, and finally around the idler pulley. Check all alignments.

8. Put the tesioner adjuster in a vise and squeeze it together until you can place a small drill bit or allen wrench through the holes to keep it compressed.

9. This is the tricky part. You will need to install the tensioner adjuster and that will require some moving of the belt to allow enough play to get the adjuster in place. This may move the passenger's side alignment. If so, you will need to try it again. I find that if you move passenger's side alignment mark clockwise by one tooth of the sprocket, then when you go to put the tensioner in place it lines up. You may find other tricks to overcome this challenge.

10. Once you think you have everything lined up. Use a wrench to turn the crankshaft sprocket 2 full turns. Listen closely and feel for any hard resistance as you do this to determine if the pistons are hitting the valves. If you believe they are hitting each other thenrepeat the adjustment procedure. Not doing this can ruin the valves or more.

11. If everything seems OK. remove the drill bit or allen wrench from the tension adjuster. Perform step 10 again for one final check.

I hope this helps.

Posted on Feb 22, 2009

  • 6 Answers

SOURCE: Were is my ABS sensor located on my 2000 Isuzu Rodeo

there should be a sensor at all 4 wheels so make sure there all pluged in 

Posted on Jul 04, 2009

Suraido
  • 195 Answers

SOURCE: ABS light stays on.

I'm guessing the ABS sensors in the wheel are defective and need to be replaced. But before you go about taking it all apart, start by checking the brake fluid level under the hood, as in some models of vehicules, the ABS light will turn on to tell you the brake fluid level is too low. If it's OK, then you can start thinking about the ABS sensors. They should be located near the axles just before the axles themselves enter the hub. You can usually find them by spoting the weird plastic units that point to a circular gear type ring with square teeth. If the sensors are all OK then there probably is a cut or damaged wire in the system.

Posted on Jul 08, 2009

  • 497 Answers

SOURCE: 1996 rodeo, ABS/Brake warning light on dim, will

Get an OBD reading

Posted on Oct 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Start engine and engineine pops for couple of


Have the ABS pump ECM checked (it is separate from the main ECM), try to catch it early. I bought a transmission last year. This is typical 98-02 Rodeo behavior.

Aug 01, 2010 | 2000 Isuzu Rodeo

1 Answer

Lights on the abs sometimes and sometimes off on a 1995 isuzu tro


I believe that was a recall item several years back

Nov 01, 2009 | 1998 Isuzu Rodeo

1 Answer

My problem is ligth abs


An ABS light is a signal there is a problem in the ABS sensing circuit. It could be a bad sensor, or a bad connection usually at the wheel or a bad wiring harness going to the sensor.

Jul 13, 2009 | 1998 Isuzu Rodeo

1 Answer

Were is my ABS sensor located on my 2000 Isuzu Rodeo


there should be a sensor at all 4 wheels so make sure there all pluged in 

Jul 03, 2009 | 2000 Isuzu Rodeo

2 Answers

Brake light works sometimes and sometimes it doesn't.


There is a switch mounted just above brake pedal, check that it is not sticking when you press pedal.

Aug 02, 2008 | 1998 Isuzu Rodeo

2 Answers

Isuzu Rodeo abs light


I had it repaired: one of my sensors needed to be replaced. No more light!

Jul 09, 2008 | 2000 Isuzu Rodeo

Not finding what you are looking for?
1998 Isuzu Rodeo Logo

Related Topics:

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...