Question about Cars & Trucks

1 Answer

Can't seem to figure out to take this out without pulling engine. It's a pain. Been without vehicle for a while and sux were still paying on it. from used dealer. It's an 02 exploder

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,101 Answers

Yes there is a way,and it is a lot of work. first drain the radiator,and take the radiator out . remove everything off the front of the motor ,remover the water pump and harmonic balancer ,and when the timing cover. how did it break and how long have you had the explorer. the motor may not be any good if that broke. this is the link to my garageI am on face book. ted's repairs in connecticut

Posted on Dec 03, 2012


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Check engine light stays on - who pays for the repair on a vehicle purchased from the dealer within first 30-days?

hey get starter fluid and start the engine go through each vacuum hose and spray each one if it is a vacuum leak the engine will slow the idle and you have found where the problem is

Posted on May 04, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 03 Taurus won't start unless I wiggle the wheel while holding key in the START position now it won't start at all and the steering wheel won't lock I tried posting this 3 times sorry I sux at this

You likely have a short in the steering column. Continuing to drive with said condition could result in vehicle fire. You need to figure out what is causing the short and resolve that problem.

Jun 11, 2016 | Cars & Trucks

1 Answer

Clunking noise when in gear and wont go anywhere

Any vehicle that exhibits that, means something bad or broken in the drivetrain, the powertrain from engine to transmission to differential to drive shaft(s) to drive wheels. Is the clunking coming from the transmission? Front wheel drive vehicles have transaxles with the transmission and differential built into the transaxle. That is true for automatics and manual transmissions. If you have rear wheel drive, check that the drive shaft has not come loose.

One last thought: front wheel drive is more expensive to upkeep and to repair than rear wheel drive vehicles. That's just the way it is, due to the construction. The only way to avoid high labor costs is to pay slavery wages or do it yourself.

Jul 07, 2015 | Cars & Trucks

2 Answers

Would it b easier 2 pull motor 2 change head on 2002 suzuki aero cant get 2 some of the accesories

MUCH easier in the long run. And if you need special tools, O'reily's might rent them to you. There are other places too. Just make sure you find out exactly what you need to do so you aren't without a vehicle! :-) Or pay a mechanic/friend.

Jan 26, 2015 | 2002 Suzuki Aerio

2 Answers

'06 taurus shuts off while driving

( now they say they can't figure out whats wrong with it unless it happens while they are driving it to know exactly whats wrong !
Even with it actting up it could be a pain to find . All the electronic's an wiring an connections , ground circuit's an B+ circuits .Plus C.A.N. Serial data network , do you know what this C.A.N. is ? controller area network , all the modules on the vehicle share info on it . The instrument cluster gauges info come's from the PCM - engine computer over this network . Here read this
How to Diagnose Controller Area Network CAN Your problem could be cause by lose ground connection ,a lose network connection . Something that mite require the dash (instrument panel ) to be pulled out of the vehicle . So don't be to ******* the dealer , they just want to be sure , because if they need to pull the dash out that can be expensive ! Close to $1,000 bucks .

Apr 07, 2017 | 2006 Ford Taurus

1 Answer

Check engine light on

have you had the code pulled from the computer.without it you have no were to start to diagnose without it.its like going to a dentist and telling the doctor that your have a pain in your mouth without giving more information or having them check it out.not enough info no help.

Jun 20, 2011 | Chrysler PT Cruiser Cars & Trucks

1 Answer

I have a 1992 Plymouth Grand Voyager with the 3.3L V6. The 'MAINT REQD' light has been on for months. I can't get the ignition cycling to give me a code readout. I don't if I'm doing...

When the Check Engine Soon Light comes on , your first instinct is to pull over and check out the situation. This is not necessary. This is the vehicles way of letting you know at its earliest stage that an error has occurred. No need to panic. If you have been driving with that all annoying light on, remember this : Your gas mileage will improve if the necessary repairs are made.

The first thing to do when your "Check Engine Soon" light comes on is to determine the immediate cause. Consider if the vehicle is still performing as usual or if a loss of performance is noticeable. Generally a constant illuminated light without loss of performance points to an emissions related issue( this won't leave you stranded). When the light flashes, this indicates a serious engine failure condition and will require immediate attention. You may wish to take your vehicle to a local shop and have Computer Diagnostics performed. Usually costs under $100.00.

Generally all vehicles from 1996 and up have an OBD II computer. The Major problem when it comes to OBD II is that you can no longer acquire the trouble codes by counting the flashes of the Check Engine light like you could on earlier OBD I vehicles. You can take your car into a local high-tech service shop, where the minimum charge for computer diagnostics and engine diagnostics might cost you somewhere into three digits. Or you may want to learn about OBD II systems. in order to do so you will need an OBD II scan tool. I have already done the research for you and located several different scan tools for you to choose from. If you already have the code and need to know what it means check out our complete list of OBD II Codes Here.

OBD II scan tools connect to the vehicle's computer through a connector under the dash by the steering wheel.


May 19, 2011 | 1992 Plymouth Grand Voyager

2 Answers

Check engine light stays on

take your car to an autozone, they will pull the code thats making your CEL go on..

Dec 03, 2009 | 2002 Suzuki Aerio

1 Answer

My check engine light keeps throwing a torque converter clutch solenoid circuit code. How do I change this part? Do I have to take the engine out? Is there a way to dropt the transmission without removing...

You cannot replace this part without pulling the tranny. The circuit is inside the tranny.
I recommend just unplugging it. All that this does is help vehicle shift smoother

Sep 16, 2009 | 2001 Nissan Altima

3 Answers

What is estimated average cost for timing belt replacement ?

should cost less than $100 at a FORD DEALER. mine cost $65 four years ago.

Apr 03, 2009 | 2000 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides