Question about 2008 Honda Pilot EX-L
Clmate control bulbs
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
As a warning, this is a little difficult and requires some patience. I just had to do with to my 2000 accord, and I'm betting the process is very similar for your '98 model. Before starting, you're going to want to get a Phillips head screw driver and a pair of pointy needle-nose pliers. The first thing you'll want to pop off it the driver's side fuse box cover. Under that you should see two screws towards the bottom that hold on the plastic trim that covers the underside of the steering column. This was held along the top with a few pins that should pop lose with a little effort (not too much force though!). There is one screw holding this piece in on the other side (holding it into the center console) but you wouldn’t need to remove this, you just need to get behind this piece of trim. Behind it, you should see two screws holding in the piece of trim that covers the side of the shifter. Take those out and it'll give you the little bit of wiggle room you're going to need. Lastly, pop off the black trim around the shifter. All you'll need to do is put something flat under it and gently pull up, working your way around it. This should pull off relatively easily. You should see the two wires leading to the bulb that will be located right in the middle on the driver's side. What you'll need to do is wiggle you're hand up under the side of the plastic side trim and grab the bulb. It will take a quarter turn to loosen it. Put the new bulb you have in the socket, wiggle it back in its proper place (don't forget to give it a quarter turn again to lock it in) and you should be set. Make sure you test the bulb before putting everything back together! I’m sure something doesn’t make complete sense in here, so if you need any clarification on anything in here, let me know!
Posted on Jun 14, 2009
You will have to pry off the lens CAREFULLY using a small screwdriver. There are two (or more) little plastic protrusions on each long side of the lens which fit into the casement. Look for very small slots along the side of the lens to insert the blade of the screwdriver. You can ease the casement away from the lens enough to get it to pop out. Re-inserting it is the same, but probably easier.
Gently, give it a try.
Hope this helps you.
Posted on Nov 21, 2009
Use a wrench to remove the mounting bolt from the underbody through the hole in the splash shield.
Remove the fog light assembly from the bumper by pulling its inner edge first, then the whole assembly out of the bumper.
Remove the electrical connector from the bulb by pushing on the tab and pulling the connector down.
Remove the bulb from the fog light assembly by turning it one quarter turn counterclockwise.
Push the electrical connector onto the new bulb.
Turn on the fog lights to test the new bulb.
Reinstall the fog light assembly into the bumper. Tighten the mounting bolt.
Insert the new bulb into the assembly and turn it one-quarter turn clockwise to lock it in place.
Hope this helps you.
Posted on Nov 22, 2009
This solution pertains to a 2008 Honda Pilot...To replace the cabin air filter which is located on the passenger side of the vehicle behind the glove box: Open glove box and remove stored items...while sitting in the passenger seat, pull towards you on each of the two clips on the left and right side of the glove box...this will cause them to become loose and the glove box will tip out completely exposing the inside of the dashboard. (Alternately...carefully pull towards you on the top center of the glove box which will cause the left and right side stops to pull away from the edges and allow the glove box to tip out) Here it gets tricky...the box holding the cartridge for the cabin air filter is the large black box on the left side behind the glove box The filter fits in a removable tray vertically inside that box. A pressure clip at the top of the box allows the vertical cover to be removed exposing the tray with the Cabin air filter... BUT!!! There is a plastic bar an inch or so high which has been placed there by the manufacturer to prevent most from changing the filter without the service department being involved. This bar must be cut with a sharp sheetrock knife or hacksaw and discarded, (it will not be reinstalled). Then there is a flat metal bar behind the plastic bar that can be removed using an 8mm socket and a phillips screwdriver. There are 2 8mm screws and one phillips head screw on each side that must be removed in order to remove the metal bar. THEN you can remove the cover to the cabin air filter box, pull out the tray with the filter (note how the filter is in the box so the new one can be placed the same way) reinsert the tray with the new filter and replace the tray cover. All other steps to finish the job are obvious as everything is the reverse. Actually the whole process is a lot of trouble and unless you are determined to change the filter I would recommend not doing it.
Posted on Apr 01, 2010
JUST POP SWITCH OUT AND BULB GOES INTO SWITCH USE SMALL SCREW DRIVER TO REMOVE YOU WILL HAVE TO TWIST IT COUNTERCLOCKWISE TO REMOVE, TWIST CLOCKWISE TO INSTALL.
Posted on Apr 21, 2010
Tips for a great answer:
Jan 30, 2017 | Honda Cars & Trucks
Nov 14, 2012 | 2008 Honda Pilot
Feb 15, 2012 | 2008 Dodge Ram 1500
Nov 09, 2010 | 2003 Kia Sorento
Nov 04, 2009 | 1998 Honda Accord
Mar 19, 2009 | 2003 Honda Pilot
192 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: