Question about 1991 Jeep Wrangler

2 Answers

91 wrangler wiring diagram for steering column harness

I have been trying to figure out what all of the wires do that come out of the column... anyone know where you can get a diagram or instruction manual for this????

Posted by on

  • 2 more comments 
  • alldread1 Jan 11, 2009

    we are trying to figure out where all the wired go... we have completly rebuilt this jeep and are now in the process of trying to get all the blinkers and such working does that help?

  • alldread1 Jan 11, 2009

    thanks for your help... if you are able to get that at your work please send it to me... i think we are going to just go and buy a haynes manual like you were suggesting. appreciate your time... to bad you are so far from mississippi!!! lol

  • work4it1 May 11, 2010

    Ahhh got ya humm well if i was there i could help but im in minnesota only thing i could say is get a book on it with a wiring digram we have a program at my work with digrmas but for some reason i cant copy them at home ill try it again if i get it ill send it to ya good luck

  • work4it1 May 11, 2010

    What exactuly are you looking to do ? fix or install ?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I would not, I am a repair facility but like I said there are melted wires and other people before me trying to repair this vehicle, so nothing is connected where it should be.

Posted on Feb 14, 2014

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 21,949 Answers

You should be able to work wires out with no problem their cant be more than about ten wires,buy a HAYNES manual ,now that is tantamount to sacriledge and who ever suggested that must stand in the corner with a big hat on marked with a capital D

Posted on Feb 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My steering column wires


Donna, steering column wire diagram, check the attached links,instruction and guides, Good luck. "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
http://alarmsellout.com/support/diagrams/vehicle/GMC%20SIERRA%201988-2005.pdf
Repair Guides Wiring Diagrams Wiring Diagrams AutoZone com
Wiring Diagram
1998 GMC Sierra steering column wiring diagram Google Search

Jul 20, 2016 | 1998 GMC Sierra

1 Answer

Highbeam work lowbeams done fuses and relay good what next


What is year--make--model of vehicle? Right now, I'd say, check the wiring circuit to and from dimmer switch. Could be dimmer switch, itself?

With wiring diagram, you can find proper color wire from steering column to low beam, everything on, see if voltage on that wire. I'm speculating that the dimmer switch controls voltage to low beam and not ground.

Under the dash, find wiring harness that goes into steering column, find proper color wire, test. If no voltage, when there should be, I think the problem is in the steering column, either wiring circuit or dimmer switch.

Nov 10, 2015 | Cars & Trucks

2 Answers

Where is circuit breaker for headlamps on a 1989 caprice


The breaker for the headlights is inside the headlight switch.
You should have a fuse and relay for the horn.
Could be a problem with the wiring harness for the steering column.

Aug 04, 2012 | 1989 Chevrolet Caprice

1 Answer

1989 wrangler 2.5L won't turn off with new switch


Hi there:Bad installing or a problem with the connections. The most likely problem is a bad ignition switch. To find out for sure, remove the plastic covers over the steering column and remove the 2 screws holding the ignition switch in place. Make sure the mechanism coming from the key is turning the ignition switch. If the mechanism works fine, replace the ignition switch.

I would suggest removing the ignition switch and checking the mechanism in the column to make sure it is actually turning the ignition switch off.


You could have a wiring problem, you will have to follow all the wiring from the ignition switch down the column and into the harness, there is sure to be a short in the wiring harness, that is if as you said you replaced the ignition switch for a new one.

To test this, remove the plastics around the steering column and pull out the wiring plug to the ignition switch, if the ignition turns off you have another faulty ignition switch if it stays on wiring harness has shorted out.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 19, 2012 | 1989 Jeep Wrangler

1 Answer

How do i install Switch Assembly turn signal Cruise control PART AUTO for a 2002 Impala.


Multifunction Turn Signal Lever Replacement - On Vehicle

Removal Procedure

83422682


  1. Verify that the multifunction turn signal lever is in the center of the OFF position.
  2. Disconnect the negative battery cable.
  3. Disable the SIR system.
  4. Remove the steering wheel.
  5. Remove the steering column trim cover.
  6. Remove the steering column knee bolster.
  7. Remove the steering column wire harness (1) from the steering column wire harness retainer (2).
  8. Remove the 2 wire harness straps from the steering column wire harness (1).
  9. Remove the steering column bulkhead connector from the vehicle wire harness.
  10. Disconnect the connectors from the multifunction turn signal lever steering column bulkhead connector.
85097560




  1. Remove the retaining bolts (1) from the multifunction turn signal lever (2).
  2. Remove the multifunction turn signal lever (2) from the steering column.
Installation Procedure

85097560




  1. Install the multifunction turn signal lever (2). Use a small flat-blade in order to compress the electrical contact and move the multifunction turn signal lever into position.
  2. Verify that the electrical contact rests on the canceling cam.
Notice: Refer to Fastener Notice in Service Precaution.


  1. Install the retaining bolts to the multifunction turn signal lever.
    • Tighten the retaining bolts to 7 Nm (62 inch lbs.) .
92905224




  1. Connect the gray and black connectors to the multifunction turn signal lever steering column bulkhead connector.
  2. Connect the steering column bulkhead connector to the vehicle wire harness.
  3. Install the two wire harness straps to the steering column wire harness (1).
  4. Install the steering column wire harness (1) to the steering column wire harness retainer (2).
  5. Install the steering column knee bolster.
  6. Install the steering column trim cover.
  7. Verify that the lever is in the center or the OFF position.
  8. Install the steering wheel to the steering column.
  9. Enable the SIR system.
  10. Connect the negative battery cable.
I hope this helps you.

Thanks

Nov 28, 2010 | 2002 Chevrolet Impala

1 Answer

Looking for a 1967 mustang steering column wiring diagram


Check out CJ Pony Parts for replacement turn signal/horn wiring harnesses. Try www.hammar.dyndns.org - he has some wiring diagrams (called schematics)

Jul 11, 2009 | 1966 Ford Mustang

1 Answer

Steering column wiring issue (colors don't match up)


have the dealer fax the wiring diagram to you that's what I do

May 22, 2009 | 1984 Jeep CJ7

Not finding what you are looking for?
1991 Jeep Wrangler Logo

415 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...