Question about Hyundai Accent
I can open the lid but when I turn the cap it will not come off. I do not want to strip it . I have tried putting pressure on it but it didn't help.
Try pressing it in and opening it it wont strif but it can break even if you break it use a big channel lock to open it and replace it with a new one.
Posted on Dec 02, 2012
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The fill tube for the fuel tank is either clogged with something or the anti-siphon feature (what stops people from stealing your gas) is fouled up. The tank and fill tube have to be inspected.
Posted on Jan 28, 2009
SOURCE: removal of disk brake
Post is a month old but maybe someone else will read it and get the information. This is actually very easy. Make sure the parking brake is set and remove the wheel of whichever side you are working on. The calipers on this have one bolt on the top that needs to be loosened. Once the top bolt is loosened you will need to pull up on both sides of the caliper to disengage it from the brake pads/rotor. Once it is disengaged it is best if you have something available to tie it off for the moment so it does not just hang as that can damage the brake line. Once you have the caliper pulled out of the way-if you are new to brake jobs familiarize yourself with the alignment of the brake pads. Each side is going to have an inner and outer pad. The pad that goes on the inside is the one that has the sensor, it is a metal clip attached to the bottom of the brake pad. Before you take the old pads out compare their position with your new pads. Using a screwdriver as carefully as possible pop out the old "outer" brake pad and put the new one back in its place. Doing only inner and outer one at a time will help with your brake hardware brackets at the top and bottom of the pads not falling/coming out of place. Then replace the inner brake pad. Once that is done what you are going to need to do is to push the caliper back in. This is done with what is called a C-clamp-medium or large size-available at most parts places. They will know what you are talking about. When you are looking at the caliper what you will notice is that in the middle it is protruding out. You need to push it back into the caliper so that it will fit the new brake pads. Put one end of the C-clamp on the edge of this protrusion and put the other end of the C-clamp on the back of the caliper. Turn the handle until it is taut and at that point it will be harder to turn but as you turn the C-clamp handle the caliper will begin receding until it is flush at which point you are ready to put the caliper back on. Put the caliper over the new pads and where you took the bolt out-you may have to push the caliper guide pin out slightly to put the bolt back in but it should be no real problem. Once you have tightened the top caliper bolt back up, put the wheel back on and do the other side. Once both sides are done before you drive the car you will need to make sure and start the car, and pump the brakes a few times so that the caliper can make firm contact with the new brake pads. After that you should be good to go
Posted on Feb 13, 2009
I have a 2005 Hyundai Accent, It is not possible to fill the tank if you are letting the petrol pump run at full speed.Trying to fill up quickly it will only build up pressure and cut off. Next time you fill up just pull the petrol pump handle half way, it will take longer to fill but you wont get the blow back. Modern petrol pumps are getting quicker all the time.Hope this helps you.
Posted on Mar 23, 2009
You have to take out the ash tray, and remove those two screws, then pop out the center dash trim. Careful, though, you have to take out a lot of the wiring inside of your center dash trim in order to pull it out for enough room to move the radio in and out. I'm doing this right now, actually..
Posted on May 22, 2009
Tips for a great answer:
Aug 18, 2015 | Hyundai Accent Cars & Trucks
Feb 08, 2013 | 2007 Hyundai Accent GS Hatchback
May 11, 2012 | 2007 Hyundai Accent 1.6
Oct 02, 2010 | 2000 Hyundai Accent
Apr 16, 2010 | 2000 Hyundai Accent
Mar 12, 2010 | 2007 Hyundai Accent GS Hatchback
Jan 01, 2010 | 2007 Hyundai Accent GS Hatchback
Apr 12, 2009 | 2007 Hyundai Accent GS Hatchback
Jan 09, 2009 | 2003 Hyundai Accent
Sep 20, 2017 | Hyundai Cars & Trucks
35 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: