Question about Toyota Celica

1 Answer

Rear brake lines completely empty on my toyota celica 95. what should i do/how do i fix it?

While replacing the caliper on the driver side rear wheel, the brake line bled out, how do i fix this problem? would i just put the bleeder bolt back in and refill it or what?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 14,200 Answers

You will need to bleed the brake system,here's a link on how to.

Posted on Dec 02, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 330 Answers

SOURCE: new brakes

Still have air inside, because you used gravity feed method.

Posted on Jul 26, 2008

  • 58 Answers

SOURCE: no brake line pressure on 1 caliper after replacing caliper

I suspect you may have twisted the hose on re assembly. The other possibility is that the bleed nipple is choked with dirt and rust. Remove it completely and see if the fluid starts to run out. If so replace nipple or clean out.

Cheers John

Posted on Dec 17, 2008

  • 78 Answers

SOURCE: any online manuals sowing how

Replace the wheel cylinder. You'll never get the broken fitting out of the old cylinder.

Posted on Dec 27, 2008

  • 334 Answers

SOURCE: 95 Avalon rear brake caliper replacement

get a hayes repair manul from the auto parts store that will tell you every thing youneed to know

Posted on Aug 11, 2009

csmock132
  • 4669 Answers

SOURCE: brake pedal needs to be depressed very hard to

The pedal goes down a long way(Rear brake shoes out of adjustment) or the pedal is hard to push and you have to about use two feet to stop the truck? (booster problem)

Posted on Jul 18, 2010

Testimonial: "rear brake shoes are adjusted tightly, pedal is not hard to depress at all,pedal does goes down further than it normally used to."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replaced some brake line, rear pads and one rear wheel cylinder. Now no pressure and nothing happening when trying to bleed.


Does the car have ABS ? And does it have an equalizer block for the 4 wheels ?
It sounds like the ABS has been affected, or there is an equalizer block that is stuck on the front wheels only.
Can you open the bleeder or the rear line on the master cyl and get fluid to come out by depressing the pedal ?

Jul 07, 2013 | 1997 Mercury Tracer

1 Answer

1996 camery station wagon , 4 wheel disc brakes. need to replace brake lines in the rear. what is the name of the junction block , with the actuator in the rear? All 4 rear lines go to and leave this...


Hello, first you Toyota has dual braking system. It goes like this: Left front brake with right rear brake, the right front brake with left rear brake. This a braking safety system that has been incorporated in auto/trucks for a few years now. If brake line is broken. loose wheel caliper, blow caliper piston, any thing that happens to the brake system. You will still have two wheels that have their hydraulic system. Also, the emergency brake will a manual system for the rear wheels.


Why do you need to change your auto brake lines? That valve you are talking about is a load stabilizer valve. It used to limit the amount of hydraulic fluid as more load is place in the rear of your Toyota. Example. by press on the brake pedal, it activates hydraulic pressure to the four wheel disk braking system. The braking system needs to stabilize the hydraulic pressure to the wheel to keep the vehicle moving in a forward motions. Now, by loading the rear of the vehicle this transfer the load disposition of the vehicle by making it heaver in the rear. Therefore, the load compensator valve limit the amount of hydraulic pressure to the rear brakes.



Another thing to remember about this rear load valve, they will get plugged. and the vehicle will not have enough braking pressure for the rear wheels. I hope I answer you question about this load portion valve in the rear of Toyota. GB...stewbison

Sep 21, 2011 | 1996 Toyota Camry

1 Answer

How to remove rear brake caliper to replace pads on 1995 Celica


With the wheel removed, look behind the caliper there are 2 bolts that hold the caliper in place. Completely remove the lower bolt and loosen the top. The caliper will then swing upwards exposing the old pads. Remove cover off master cylider reservior. Leave both old pads in place for now. slide the far side pad over to the near side pad and using a channel-lock wrench, squeeze slowly and steadily. this will cause your brake cylider to retract, pushing the fluid backwards through the line and into the reservior. Once the cylinder is retracted, remove old pads and place new pads on either side. Align caliper and swing it down. Replace lower bolt and tighten upper.

Sep 23, 2010 | 1993 Toyota Celica

1 Answer

I need step by step instructions on how to bleed brakes on my 2005 toyota celica


If you don't have someone to help you you'll need to get a one man brake bleeding kit. The bleeding kit will take the place of the helper. IF you have a helper start with the rear passenger side wheel (furthest from master cylinder). Remove the wheel, have a helper sit in the vehicle and pump the brakes several times (motor off). Tell them to hold the pedal down while you open the bleeder screw. Tighten the bleeder screw before the helper releases the brake pedal to avoid sucking air back into the line. Repeat this process until the fluid flows out of the bleeder with no air. Then repeat these steps on each wheel. The order of bleeding is always furthest from the master cylinder. Rear passenger, rear driver, front passenger, and lastly front driver. After each wheel is done check the fluid level in the master cylinder and add as necessary. You don't want it to get low and **** air in from the cylinder.

Nov 06, 2009 | 2002 Toyota Celica

1 Answer

95 Avalon rear brake caliper replacement


get a hayes repair manul from the auto parts store that will tell you every thing youneed to know

Aug 11, 2009 | 1995 Toyota Avalon

1 Answer

Rear brakes not completely disengaging


your inside pad wore out first do to a bad caliper or frozen slide or brake hose.remove brake hose off the caliper and see if you can turn the wheel.if you can replace hose and bleed caliper.if wheel still doesn't move buy a loaded caliper,this will come also with new slides!and then bleed

Jan 25, 2009 | 1994 GMC Jimmy

1 Answer

How do i take off the disc brakes on my 2001 toyota celica?


These instructions came from Auto Zone's website and their free, online repair guides. Just plug in your make, model and year and you can get exact instructions and pictures for your repair. Sweeeeeeet! Good Luck!
  1. Loosen the wheel lug nuts slightly.
  2. Raise and support the vehicle safely.
  3. Remove the wheels.
  4. Disconnect the brake hose from the caliper. Plug the end of the hose to prevent loss of fluid. Some brake lines have a union bolt and gasket type line attached to the caliper. Do NOT lose the washers.
0900c152801a856d.jpgRemove the brake hose union bolt with gaskets from the caliperHave a container handy to catch brake fluid from the disconnected lines.
  1. Hold the sliding pin and remove the bolts that attach the caliper to the torque plate.
0900c152801a856e.jpgRemove the two bolts that attach the caliper to the backing plate
  1. With two hands, lift up and remove the caliper assembly.
To install:
  1. Grease the caliper pins and bolts with Lithium grease or equivalent. Temporarily install the caliper on the torque plate with the installation bolts.
0900c152801a856f.jpgThe sliding pins should be greased with Lithium-based grease before installation
  1. Hold the sliding pin and tighten the installation bolts to 25 ft. lbs. (34 Nm) on the front wheels, and 14 ft. lbs. (20 Nm) in the rear.
  2. Attach the flexible brake hose to the caliper with new gaskets. Tighten the hose to 22 ft. lbs. (30 Nm).
Install the brake hose lock securely in the lock hole, in the caliper.
  1. Fill and bleed the system.
  2. Install the wheel, lower the vehicle and tighten the lug nuts.
  3. Before moving the vehicle, make sure to pump the brake pedal to seat the pads against the rotors.
  4. Check for leaks.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the wheels.
  3. Disconnect the brake hose from the caliper.
  4. Remove the bolts that attach the caliper to the torque plate. If applicable, hold the flats of the sliding pin with a wrench while loosening the caliper attaching bolts.
  5. Lift up and remove the caliper assembly.
To install:
  1. Install the caliper and loosely install the bolts.
  2. Hold the flats of the sliding pin with a wrench, then tighten the bolts. Tighten to 25 ft. lbs. (34 Nm) except on Celica rear calipers. Tighten the bolts on Celica rear calipers to 34 ft. lbs. (47 Nm).
  3. Connect the brake hose to the caliper, using 2 new washers.
  4. Fill the brake system to the proper level and bleed the brake system.
  5. Add brake fluid to the reservoir to fill to the correct level.
  6. Lower the vehicle to the ground.

Jul 17, 2008 | Toyota Celica Cars & Trucks

1 Answer

New brakes


Still have air inside, because you used gravity feed method.

Jul 17, 2008 | 2000 Chrysler Cirrus

2 Answers

1995 Toyota Celica Front Wheel Hub


can u replace the bearing in the hub? will that fix your problem?

May 25, 2008 | 1995 Toyota Celica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...