Question about Mitsubishi Cars & Trucks

Open Question

Mitsubishi lancer 2011 Airbag module location

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 599 Answers

SOURCE: location of fuel filter for 2005 Mitsubishi Lancer 1.8 litre

a guess... fuel filter should be up against subframe behind rear wheel in front of fuel tank...follow fuel lines down frame rail from motor to back end to find it.... good luck

Posted on Dec 26, 2008

  • 1 Answer

SOURCE: 06 kia sportage airbag control module

If your refering to the light on top of the dash that says "psgr air bag not connected" here;s the deal.

The module is activated when someone sits in the seat. Turn the key on and the notification will light. Go around to the psgr side of the car and sit in the seat and the light should go out.

Posted on May 03, 2009

  • 412 Answers

SOURCE: Needing to locate the airbag control module '07 caliber

it is located behind the floor shifter in center console..under small piece of carpet

Posted on Jun 20, 2009

  • 333 Answers

SOURCE: I have problem on airbag codes in mitsubishi lancer

Your first code is for low system voltage. If your battery has needed a jumpstart lately or replacement, this code will be set.

The second two codes are in relation to your rh side airbag (B1C2D) and curtain bag (B1B22) not being visible to the srs ecu. Has the car been apart for any reason, possible leaving harnesses unplugged? Was it in an accident recently and maybe the bags are missing? Were components removed for accessory installations (stereo, subwoofers, etc)?
The connector for the curtain bag is in the passenger side rear most pillar. The connector for the side airbag is under the passenger seat.

A weak battery can sometimes throw other miscellaneous codes like these, but it is not likely. If you clear the codes, the B1C2D and B1B22 should come right back.
If they do, and both bags are installed correctly, You can bypass them with a 3 ohm (three ohm) resistor and clear the code again. If the codes set again, there is a problem with the wiring leading up to the squib units. If the codes do not set again, there is a problem with the squib units.

Posted on Sep 10, 2009

  • 89 Answers

SOURCE: How do i reset the srs airbag light in a 1996

you need to repair your airbag computer it has a crash data more info on http://www.vehix411.com

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Mitsubishi lancer radio from loud squealing noise


What is causing that irritating noise? ' DSMtuners

www.dsmtuners.com > ... > Articles: Miscellaneous
Jun 1, 2009 - 2 posts - ‎1 author Check the ECU power relay in the console, under the radio. ... You hear a loud clicking type noise from under the hood when you try to start the car. .... You hear a squealing, grinding, or rubbing noise in the lower timing belt .... The Mitsubishi Eclipse, Eagle Talon, Plymouth Laser, Mitsubishi Galant VR-4, ... LOUD squeak when turning steering wheel (Video Inside)
22 posts
Mar 5, 2011
Why does my alternator belt squeal so much on initial ...
25 posts
May 14, 2010
More results from www.dsmtuners.com

Lancer Troubleshooting [Archive] - evolutionm.net

www.evolutionm.net/forums/mitsubishi-evolution-forums/f-203.html
NEED RADIO HELP! ... Help not start Lancer GT 2012 EngineOverheating STOP SAFELY warning on ... AC ISSUES 2011 Mitsubishi Lancer ES · 2008 Lancer GTS no start please ... 2011 lancer no sound · Driver/Passenger side floor squeaky? ... plastic piece of rear shelf rattles a lot · Very loud noise on Lancer ES 2008 ...

Dec 03, 2015 | 2008 Mitsubishi Lancer GTS CVT Sedan

1 Answer

Location of airbag module 2011 Chrysler 300


Not sure about the 300 but I had a stratus and a intrepid plus worked on other dodge vehicles and module was in passenger compartment

Feb 27, 2015 | 2011 Chrysler 300

1 Answer

Where exactly is the fuel filter located on my 2003 mitsubishi lancer?


there is no in-line fuel filter, there's only one in the tank and it's part of the fuel pump module

bd779e1.gif

Mar 28, 2010 | 2003 Mitsubishi Lancer

1 Answer

Can you please tell me where is the fuel pump on a mitsubishi lancer 2001 model its not under the back seat


The fuel filter is located WITH the fuel pump AKA fuel module is what Mitsubishi calls this bundle, to access remove rear seats where you will find the cover to the assembly. The Fuel pump and Fuel Filter are intergrated to each other to save weight.

Jan 17, 2010 | 2002 Mitsubishi Lancer

1 Answer

I have problem on airbag codes in mitsubishi lancer


Your first code is for low system voltage. If your battery has needed a jumpstart lately or replacement, this code will be set.

The second two codes are in relation to your rh side airbag (B1C2D) and curtain bag (B1B22) not being visible to the srs ecu. Has the car been apart for any reason, possible leaving harnesses unplugged? Was it in an accident recently and maybe the bags are missing? Were components removed for accessory installations (stereo, subwoofers, etc)?
The connector for the curtain bag is in the passenger side rear most pillar. The connector for the side airbag is under the passenger seat.

A weak battery can sometimes throw other miscellaneous codes like these, but it is not likely. If you clear the codes, the B1C2D and B1B22 should come right back.
If they do, and both bags are installed correctly, You can bypass them with a 3 ohm (three ohm) resistor and clear the code again. If the codes set again, there is a problem with the wiring leading up to the squib units. If the codes do not set again, there is a problem with the squib units.

Sep 10, 2009 | 2008 Mitsubishi Lancer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...