Question about 1991 Ford Ranger Supercab

2 Answers

Why would oil come thur pcv into trottle body

Posted by on


2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Ford Master
  • 2,101 Answers

Because the hose from the throttle body is vacuum and pcv is a valve . your is bad and letting oil by it

Posted on Dec 02, 2012

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    Uploaded 5 video answers.

  • Expert
  • 104 Answers

Bad piston rings its coming with blowby gases

Posted on Dec 02, 2012


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 21873 Answers

SOURCE: why would trottle body be getting oil after changing pcv and oil sep and running sluggish now

Could be a problem with the vent line for the crankcase - it connects thru the air cleaner box.

Posted on Dec 09, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2006 Chevrolet, HHR what makes it drink so much oil?

piston ring too much wear
pcv valve system
is there oil in air filter or trottle body could have ventilation block

Oct 08, 2013 | 2006 Chevrolet HHR


Automotive Vacumn Lines

Those vacumn lines that always have the boots and right angles that break; Okay try this;
From that old set of spark-plugs wires layin' in the corner, grab one and give it a firm pull on the boot; that boot will replace the right angle on the pcv valve: the one going in the the top the valve-cover and connected to the intake or trottle-body depending upon ,odel of car.
Remove the crumbled-up right-angle from the pcv valve and line and give the spark-plug boot a firm push and twist and it'll slide on, use a spot of oil and it'll even slide over the 3/8' lines, if you don't have oil, spit on the boot then push it on the valve and line .
This will work on many models and makes.

on Dec 07, 2009 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Why would trottle body be getting oil after changing pcv and oil sep and running sluggish now

Could be a problem with the vent line for the crankcase - it connects thru the air cleaner box.

Dec 09, 2012 | 1991 Ford Ranger Supercab

1 Answer

Gas pedal hard to push and wont accelrate and have vibration around transfecase

gas pedal a bind in cable or stuck trottle body plate stuck or broken springs at trottle body. vibration drive shafts of transfer case going out ck fluid for metal ck shafts.

Jul 29, 2012 | 1997 Jeep Grand Cherokee

2 Answers

Can't find the pvc valve on a 2001 chevy tracker. I need a diagram or a very good description to fid it. thanks. Elmer.

  • As you face the front of the engine look just to the right of the trottle body and down a couple inches. Your PCV valve is is in the back side of the valve cover gasket. Should have a spring clip on it.
  • I have uploaded a pictur indicating where the throttle body is located.

  • ironfist109_176.jpg

  • Also here is a pic showing the hose that should lead to your PCV valve (moving towards the engine)

  • Hope this helps and thank you for using FixYa.

Regards, Tony

Jul 13, 2011 | 2003 Chevrolet Tracker

1 Answer

Can the Electronic Trottle Body be cleaned without replacement.

Most certainly, should be part of regular maintence since Envoys don't have a pcv valve, so the throttle body tends to gum up quickly. Should keep it nice and shiny, using throttle body cleaner. Very simple job. One thing to remember, disconnect the battery while cleaning it. There is a tiny stepper motor that will fry if there is power on and you're moving the butterfly. Also, be careful, the butterfly is very very sharp.

Nov 30, 2010 | 2003 GMC Envoy Xl

1 Answer

Trottle body gets black have changed Oil etc he

How do the breather valves look on top of the valve cover?

Oct 28, 2009 | 1994 Jeep Grand Cherokee

2 Answers

Need to know what the throttle body looks like & how to replace it..

The trottle body is located on the intake manifold. There will be a black tube going to it. This tube is the breather tube and on the opposite end is the air filter and it container. You trottle cable and cruise control cable will also be attached to it. If you are unsure of its location, have a friend get inside the car and work the gas peddle. While you are looking at the top of the moter, you should see the linkage at the trottle body moving. Tha linkage is part of the trottle body.

Sep 16, 2009 | 1996 Mazda Protege

3 Answers

2006 Saab 9-7 SUV 5.3 V-8 oil consumption

It is probabley worn rings so the best thing to do is at next oil change get a can of V-8 formula engine restore it takes the place of about half a quart of oil I think to be exact I think the restore for a V-8 is a 15 ounce can.Try that at oil changes.

Aug 05, 2009 | 2006 Saab 9-7X

Not finding what you are looking for?
1991 Ford Ranger Supercab Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides