Question about 1995 BMW 3 Series

Open Question

Need to replace ignition key switch on 1995 325i bmw

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
mrmx2333
  • 56 Answers

SOURCE: how to replace the ignition key in my 2005 bmw 645ci

this can be very difficult to do you must make sure the baterry for the vehicle is disconnected you must remove the casing around the location of the ignition key barrel and there should be a few little pins holding the cylinder in itself with a plug attached be advised though some vehicles with electronic keys may crank over but not run without reprogramming the computer because the car may read the new key set up as someone trying to steal the car just make sure the battery is unhooked this is very important

Posted on Dec 19, 2008

Ad
  • 32 Answers

SOURCE: 1994 bmw 735i removal of old ignition switch and

bimmerfest.com

Posted on Oct 13, 2009

  • 14036 Answers

SOURCE: how do you replace the ignition switch lock on 1992 BMW 325i

WHEN INSTALLING THE IGNITION SWITCH IT SHOULD BE INSTALLED IN THE STEERING WHEEL LOCK POSITION.

Posted on Nov 14, 2009

  • 40 Answers

SOURCE: replacing a ignition key cylinder lock housing

the thing is that you can replace it, but the still will not run, the transponder and key have to be reprogrammed at the dealer only

Posted on Jul 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key in ignition light


Most likely will just need the ignition switch replaced. This is the electrical portion of the ignition, not the metal cylinder where your key goes. You will need to pull off the steering column plastic clamshell behind the steering wheel to access it. It is attached to the back of the key cylinder. It is not too expensive or hard to replace.

Apr 22, 2014 | 1994 BMW 5 Series

1 Answer

How do I change the ignition switch. my car won't start. the ignition key turns completely around


Hi if its just the ignition switch that needs replacing then all you need do is remove the cowling/shroud around steering column there are 2x 30mm Torx screws 1 at the rear of the switch 1 under the switch and 2 small flat head grub screws holding the the switch in place.

Sep 16, 2013 | 1995 BMW 3 Series

1 Answer

Ignition key wont turn in 1994 bmw 325i


force turn key wiggle steering wheel at same time if wont turn lock needs replaced or repaired,if turns may no work again and needs replaced.

Aug 01, 2012 | BMW 325 Cars & Trucks

1 Answer

Bmw no power


You need to replace your ignition switch.

Jul 06, 2009 | BMW 528 Cars & Trucks

1 Answer

1992 bmw ignition lock assembly replacement


BMW ignition lock replacing.

According to manual no special tools needed. here procedure!

  1. Ignition elec switch. Disconnect battery. 2. remove trimpanel from lower leftside of instrument panel. remove screw retaining lower steering column and remove cove. 3. remove slotted screws on both side of switch. 4. relase tabs and remove switch from elec harnass and remove sealer.. note: before mating new ignition elec switch check that switch is in correct position. seal screws again.
  2. Ignition lock cylinder replacing. 1. insert master key and turn 60 deg to radio position. 2. inset piece of stiff wire into opening in lock cylinder and pull cylinder out. (Note early models up to 10/95 turn lock cylinder back 12 deg to release)

Jun 13, 2009 | 1992 BMW 3 Series

2 Answers

Ignition bmw 318ti 1998 compact


replace ignition switch with a new key.

Apr 25, 2009 | 1996 BMW 318

1 Answer

Bmw 316i


hi markjones, the ignition switch can usually be removed without too much disassembly. First you will need to remove a plastic screw in the upper and lower trim covers. Seperate the covers. You should see a black plastic ring around the mechanical switch. gentley remove the ring. Next remove the rubber o-ring/band. With the key in the iginition and turned to almost to position 1, insert a heavy duty paper clip, or bmw special tool (about $30 from the dealer) into the small hole in the switch. There is a cam in the hole that needs to be twisted clockwise so the cylinder can be removed. When installing a new switch make sure to remove the little tab pice of metal that usually breaks off in the housing. Also be sure to make sure and reinstall the rubber ring/band because they are part of the ews system. If you key turns continuously, or is not able to be removed, the ignition housing and cylinder both will need replaced. Replacing the lock housing is about a 2 hour sequence and can be challenging. I would recommend a shop for that kind of repair.

Jan 19, 2009 | 1996 BMW 318

1 Answer

Poss ignition problem


Hello!

Sounds like a stuck ignition relay. 
Try tapping with something ******* the ignition switch when this happens, see if it helps.
If it does consider replacing the ignition switch.

Hope this helps!

Sep 27, 2008 | 1996 BMW 318

Not finding what you are looking for?
1995 BMW 3 Series Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Anthony Jones
Anthony Jones

Level 2 Expert

128 Answers

Frankie B

Level 2 Expert

65 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...