Question about 1993 Honda Accord

2 Answers

I am replacing a rear wheel bearing and need torque specs for the spindal nut

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 4,369 Answers

I don't have Honda specs, but normally it is @ 75 - 100 ft lbs.

Posted on Jan 11, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 103 Answers

I don't have a exact spec, but i've done this job several times. I always hand pack the bearings to make sure they're good and lubed, then I assemble the spindle turning the bearing while I'm tighting it down. I apply torque till there isn't any more play left in the spindle, usually no more than 15ft/lbs. then put the pin back in. if you're really worried assemble everything leaving the bearing cap off then try to wiggle it with the tire on if it moves just give it a little more. you just want it tight enough to remove all the play.

Posted on Jan 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front wheel bearing specs on Toyota t100 1995 4 wheel drive


You tighten the nut until the wheel starts getting hard to turn, then back off the nut 1/4 turn.

Jun 18, 2015 | Toyota T100 Cars & Trucks

1 Answer

What is the torque spec for the rear wheel hub bearing nut?


Torque spec is 200Nm / 148 ft lbs for the axle nuts front and rear

May 02, 2015 | 2005 Ford Freestyle SEL

1 Answer

Install driveshaft


all vehicles are similar. remove wheel,remove axle nut,remove tie rod ,remove lower ball joint ,pull spindal and rotor back pushing axle thru at same time,use pry bar to pop axle from tranny, reversal to install, push axle into tranny,pull spindal/rotor back install axle end into hole reset lower ball joint ,tie rod end. then most important TORQUE AXLE NUT TO PROPER SPECS if you dont you will ruin the wheel bearing. not fun to do in the driveway and sometimes all these parts are a real pain to remove
even on a hoist with the proper tools so beware and for the love of life dont hammer on the end of the axle

Aug 15, 2014 | 2003 Volvo XC70

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd


4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal
      06017-esca-g94.gif

      Inner wheel bearing removal-rear hub/bearing
      06017-esca-g95.gif

      Rear wheel bearing removal-2wd
      06017-esca-g96.gif

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable
    06017-esca-g97.gif

    Rear wheel bearing installation
    06017-esca-g98.gif
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

1 Answer

Replaced rear axle pinion bearing and seal, need to know pinion nut torque spec. for aam rear axle 2005 dodge 3500 4x4 Thanks.


There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to aquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Apr 19, 2010 | 2005 Dodge Ram

1 Answer

Need the 2000 Buick LeSabre rear wheel Hub nut torque spec.


Those are not nuts, they are bolts. The torque spec for those bolts is 52ft.lbs

Jul 12, 2009 | 2000 Buick LeSabre

1 Answer

What all do i remove to replace the rear wheel bearings on a 1995


First jack rear end up and block it..Remove the rear tires,Take off caliper and caliper bracket..Next remove the rotor,Then there will be a big nut in the center that the axle is bolted to.Remove that nut..Then make sure thees no wires for abs or any other kind of wires connected to the bearing.Next you should see 3 bolts holding the bearing in maybe 4 they changed them so many times..After removing the bolts you'll probably need a hammer and a chisel or air chisel to get the bearing out..Be careful when doing this to not damage the holder thats holding the bearing it.Go all the way around it with the chisel working all corners to removing the bearing..By now you should have progress on getting it out.Repeat process to installing the new one..Just be very carefull in not ruining the new one and there is a torque spec on the center nut that holds the axle and tightens the bearings preload.Call your local parts store for torque spec on rear axle nut.If you don't get the right amount off torque will result in early failure.Not to tight and not to loose.It not that major and it may seem but will save you money in the end..So dont forget to get the torque specs.Good luck and happy I could help..

Mar 30, 2009 | 1995 Ford Thunderbird

2 Answers

How to replace front wheel bearing on 2003 GMC ENVOY


Jack up vehicle and support with jack stands
Take off wheel
remove brake caliper
remove caliper bracket
remove rotor
remove axle retaining nut cotter pin
remove axle retaining nut
remove axle from output flange
pull axle out of vehicle
hub and bearing assembly held in by 4 bolts

installation is reverse of removal. You will need to find out the torque specs for the axle retaining nut.

Jan 14, 2009 | 2002 GMC Envoy

Not finding what you are looking for?
1993 Honda Accord Logo

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...