Question about Cars & Trucks

Open Question

My 98 ford laser GLXi automatic sedan want strat

I have a 98 ford laser GLXi. This morning I got up to go down the street, not a problem starting the Laser. I parked the car outside the Chemist and when I came out to start the car it would not start. The engine turns over alright no problem it just does not want to start. I have also noticed that when we had those very hot couple of days last week so was struggling even to the point where she would cut out, I stopped a few times to let it cool a little and this would fix my problem briefly. can you help please.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: automatic choke stopped working- difficulty start- revs dropping low at stop

Quick and easy attempt to fix might be to try some fuel injector cleaner,the purple bottle stuff I put in, is only about $3 a bottle, and seems to eliminate similiar symptoms brought on by bad gas.

Posted on Jun 15, 2008

Ad
  • 142 Answers

SOURCE: ford laser 1994 station wagon won't start

sounds like the timing is out, the battery is low and the fuel filter may need to be changed. cheers !

Posted on Feb 20, 2009

jameel infot
  • 15 Answers

SOURCE: Engine warning light on Nissan Almera 03

its very simple. You can see a black hose from the engine which connects the metal pipe. just remove it and you can see three gold color pin from the metal pipe. scratch that pins using a salt paper and fix it. Now check whether you get started or not. Thanks.

Posted on Jul 03, 2009

  • 122 Answers

SOURCE: 1990 Ford Laser not starting properly

change the main power cable from the battery to the stater or the solenoid

Posted on Aug 20, 2009

  • 11 Answers

SOURCE: ac compressor does not turn on when car has been sitting & it's hot outside. Works fine in the morning.

either the freon charge is about 1/3 low, or the expansion valve needs to be replaced. Freon is getting into the evaporator, but not in great enough volume to cool the air unless it is coming in cool to start with. check your ac charge, and if it is full, then have it emptied, change out the expansion valve, and recharge it

Posted on Sep 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Im trying 2 locate where to put the clutch fluid in my 94 ford laser 1.6 glxi 5d


normally its brake fluid on the master cylinder there a hosethat goes or containr that bring oil to the master cylinder of the clutch

Apr 11, 2015 | Ford Laser Cars & Trucks

1 Answer

I have a 200 1.6 glxi in thailand, have intermittant engine shut down, electrical as all goes off, sometimes instant re start, back fire, and away, otherwise start off the key whilst rolling, i have c


check the battery terminals and posts are shiny clean and tight. Check for loose wires and other terminals that may be dirty or loose.. Have the fault codes read

Mar 25, 2014 | 1998 Ford Laser

1 Answer

Idling problem


it's supposed to do that as the choke is working to warm the vehicle, when it warms up to operating temperature the choke goes off

Feb 10, 2014 | 2012 Chevrolet Impala LS Sedan 3.6L V6 FFV...

1 Answer

Brake lights ceased working.


-Make sure the correct fuse.
And did you check the bulb? If yes the bulb are good.
-next check power at the bulb. Ask a helper to help you brake and
check any power there or not. If yes there is power. Then the problem is NOT Ground.

Good Luck

Mai

Nov 11, 2013 | 1998 Ford Laser

1 Answer

How to tighten a loose clutch pedal on Ford Laser GLXI 1998 5 speed manual hydraulic clutch


Firstly bleed out any air in the clutch system. If that doesn't t work check for fluid leaks at the slave cylinder and if none replace the clutch master cylinder

Oct 13, 2013 | Cars & Trucks

1 Answer

98 lancer wagon idle problems


I pulled the Dip Stick out to check the oil while the car was idling today. the idle speed dropped and the car almost stalled.
May be worth checking into.
I have a 98 Lancer Wagon GLXI

Nov 17, 2012 | 1998 Mitsubishi Lancer

1 Answer

Ruff starting 98 ford contour in the mornings


i have a 1996 contour it dose the same thing but when im at a stop light i have to hold my foot on the gas and the breaks so it wont die. but i dont have a solution but i need one

Apr 01, 2010 | 1998 Ford Contour

1 Answer

Duramax black smoke under meduim load and over heats


my twins 98 ford taurus has a problem. it started with the motor fan not shutting down it was shut off, then i shut down finally. they were driving to work this morning, when they got therethe car started smoking black smoke and throw all the water out. can this be a fuel pump

Jul 23, 2008 | Chevrolet 2500 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...