Question about 1990 Jeep Wrangler

1 Answer

Marble noise in my 1990 Jeep wrangler

Upon acceleration there is a marble noise mannual transmission 4 cyl no one knows what it is

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Does it sound like its getting faster as you accelerate? could be the throw-out bearing in your clutch

Posted on Jan 03, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
bunnydawg
  • 5158 Answers

SOURCE: jeep backfiring

timing belt

Posted on Nov 12, 2008

bigc73542
  • 108 Answers

SOURCE: Jeep Wrangler 6 cyl. idles up and down

Have your oxygen sensor checked, one of the symptoms of a faulty oxygen is an up and down idle.

Posted on May 04, 2009

jigsaw_9077
  • 308 Answers

SOURCE: Dont know were to put in new transmission oil on a 1992 Jeep Wrangler

the plug of the transmission of 1992 jeep is under the transmission case .

Posted on Jul 20, 2009

  • 4 Answers

SOURCE: 1990 jeep wrangler rear end "bang" noise then jeep would move,

I had the same thing happen. Your rear drive shaft u-jount is bad. Also wnat to check the level of gear oil...

Replacing the u-joint takes about an hour to do... not a tough job.

Posted on Sep 30, 2009

  • 6982 Answers

SOURCE: caster adjustment for 1990 jeep yj wrangler

caster is adjusted at the rear of the lower control arms. Camber is fixed and cannot be adjusted by normal means (though special off-set ball joints are available to do that) Toe in is adjusted by turning the sleeves in or out on the tie rod ends. None of this should be done at home though crude adjustments can be made in order to get the front end reasonably straight. Adjustments are made on an alignment machine that allows precise adjustments to all you mentioned as well as front/rear tracking.

Posted on Mar 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace the bell housing of a 1989 jeep wrangler 4-cyl 4x4?


why are you replacing the bellhousing?,it means you are going to have to pull out the motor or the gearbox/transfer case,whichever is easieast

Jul 04, 2014 | 1989 Jeep Wrangler

1 Answer

How to repair fuel injector and timeing chain


get a haynes manual at a discount place or search online

May 26, 2010 | 1990 Jeep Wrangler

1 Answer

1990 Wrangler: I have a 1990 yj with the 4.2, my question for eve...


Most 90 wranglers from 89 to 95 have an ax15 5 speed transmission in them. The 4 cylinders had an ax5 transmission.

May 17, 2010 | 1990 Jeep Wrangler

1 Answer

I have a 1990 4 cyl jeep wrangler i just filled tank with gas drove 1 block and jeep stalled. Jeep starts right back up but will not stay running seems as though its not getting enough gas. Is this a fuel...


if you just filled up i might be dirty fuel go get some fuel injector cleaner stp is good, lucas is better dump in your tank and cross your fingers you might have to start up a couple times.

May 15, 2010 | 1990 Jeep Wrangler

1 Answer

I have a 90 jeep wrangler, 4cyl and 5 speed transmission, when i accelerate in any of the gears, it makes a popping noise and the second it makes that noise it seems like the jeep stops pulling, if you...


It sounds like it is the throw out bearing. From your description of the vehicle not pulling its weight, it is going to need a clutch. The throw out bearing will come in most clutch kits, so when you replace the clutch you can replace the throw out bearing, pressure plate, and pilot bushing.

Oct 18, 2009 | 1990 Jeep Wrangler

Not finding what you are looking for?
1990 Jeep Wrangler Logo

Related Topics:

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...