Question about 1994 Volkswagen Jetta

Open Question

Torque settings for a vw jetta 3, 1.6 - 1994 Volkswagen Jetta

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 46 Answers

SOURCE: 2000 VW jetta; what is the torque for valve cover and plenum

I briefly looked online and did not see any info direct6ly relating to the torque spec of the cover bolts. I would guess around 15 ft lbs.--not too much--the head is aluminium--best way to go is to walk up to the service counter of the VW dealer and ask him to provide that information. You have the car and they built it!

Posted on Apr 09, 2009

  • 15 Answers

SOURCE: VW Jetta torque setting and hub nut size????

129 ft/lbs. Per Bentley...I'm pretty sure it's a 30 mm 12 point socket.

Posted on Jun 01, 2009

1chris1
  • 72 Answers

SOURCE: how do you set the timing of a vw jetta 3

Get no.1 piston at tdc(top dead center)with cam at firing no.1 piston.fit your cam belt.and check your timming marks.Crank pulley marks and cam pulley marks.If you tell me what motor you have in there i can give you more details

Posted on Aug 08, 2009

  • 271 Answers

SOURCE: What is the Torque setting for Sump Plug VW T25

25Nm

Posted on Apr 26, 2010

  • 5 Answers

SOURCE: 1998 vw jetta front axle nut torque ???

i think it is about 140. i am not sure, in the past i use a impact gun, then give it a 1/4 turn and lock it down

Posted on Aug 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 vw jetta 1.6 turbo diesel,what is the cylinder head bolt torque spec?


!st thing is get the revised head gasket (used on 1993 up) for this engine from VW or Felpro, always use new head bolts or a repeat failure will occur. Using the revised head gasket here is the procedure to torque the head down, it is done in stages. PLease go to this site and read the whole procedure.

Feb 07, 2012 | 1992 Volkswagen Jetta

1 Answer

How many motor mounts need to be replaced on a 2002 vw jetta 1.8t


YOU HAVE 3 MOUNTS. YOU HAVE PASSENGER SIDE ENGINE MOUNT. YOU HAVE DRIVER SIDE ENGINE MOUNT AND THE LOWER TORQUE STRUT MOUNT TO TRANSAXLE.

Feb 20, 2011 | 2002 Volkswagen Jetta TDI

1 Answer

What is the torque for the rear wheel bearing nuts on 1991 vw jetta diesel


Temporarly torque the axle nut to 87 in.lb., while turning the brake drum by hand. Then loosen the nut slightly. Tighten the axle nut again, slowly and in small increments while turning the wheel, until the thrust washer can just barely be moved back and forth with a light push from the tip of a screwdriver.

Oct 30, 2010 | 1991 Volkswagen Jetta

1 Answer

2000 VW jetta; what is the torque for valve cover and plenum


I briefly looked online and did not see any info direct6ly relating to the torque spec of the cover bolts. I would guess around 15 ft lbs.--not too much--the head is aluminium--best way to go is to walk up to the service counter of the VW dealer and ask him to provide that information. You have the car and they built it!

Apr 09, 2009 | 2000 Volkswagen Jetta TDI

1 Answer

Engine torque settings VW lt 35 1993 2.4 turbo diesel. Code ACL


bob go to collsionrepairadvice.com and I will send the download to you its a big file

Mar 13, 2009 | 2000 Volkswagen Jetta TDI

1 Answer

VW Jetta torque setting and hub nut size????


129 ft/lbs. Per Bentley...I'm pretty sure it's a 30 mm 12 point socket.

Mar 13, 2009 | 2002 Volkswagen Jetta TDI

2 Answers

2000 vw jetta 1.8 automatic shifts hard between 3rd and 4th gear


Shop for a rebuilt transmission, or get an estimate from AAMCO for a rebuild job, but it won't be cheap. Get at least 3 estimates before you decide how to proceed. Good luck.

Jan 30, 2009 | 2000 Volkswagen Jetta TDI

Not finding what you are looking for?
1994 Volkswagen Jetta Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...