Question about Cars & Trucks

1 Answer

I need cvc axle for G20 1994 - Cars & Trucks

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    Uploaded 5 video answers.

  • Expert
  • 104 Answers

Go to auto zone

Posted on Dec 02, 2012


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 11896 Answers

SOURCE: cvc to motor

Yes. You will not be able to get the motor out unless you remove the axle

Posted on Apr 01, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Diagnosing bad cvc axle

cv axles have a distinct click when turning corners at slow speed when they are on the way out
if bad they will produce a harmonic vibration or a hum

May 14, 2016 | 2005 Hyundai Tucson 2.7

1 Answer

Do u need to put longer CVC axle in it,when u put a 2 inch lift

Check this with a cv axle rebuilder or an off road shop . I would think there would be problems as the axle would tend to pull out of the diff when the wheel drops in a hole or is extended fully down

Jul 31, 2014 | Cars & Trucks

1 Answer

How do i get the cvc axle out of a 1999 plymouth voyager

first secure the vehicle with wheel chocks and use the emergency brake. Loosen the wheel nuts then jack up the car. The brake rotor and caliper also need to come off. Use a piece of wire to support the caliper so you won't damage the brake hose. This should allow access to the axle. There may be a clip or a pin that holds the axle to the transmission . Once these are removed the axle should slide out. Replace in the reverse order.

Jul 13, 2014 | 1999 Dodge Caravan

1 Answer

Steerinf issues

My guess is that you have a cvc joint that's gone bad.. (A cvc joint is a joint in the kind of drive shaft (axle) that comes out of the trans-axle to the wheel.) I'm thinking you need a shop for this problem. It's not an easy repair for a novice. You'll probably need to have the joints on both axles repaired.

Dec 03, 2013 | 1990 Chrysler LeBaron

1 Answer

When doing a right hand turn I hear a clicking sound up front.

one of your cvc boots has leak the grease out of the axle clicking noise is the dried axle..replace which ever axle it is complete with new boots use rebuilt axle lots cheaper an their fine

Aug 15, 2010 | 1995 Toyota Camry

2 Answers

Clacking noise o n ft passengers side when turning to left.

poss u have a bad cv axle in the front or brake pads are loose

May 31, 2010 | 2000 Nissan Xterra

1 Answer

Changing cvc joints 1997 accord

replace the entire CV axles. Support vehicle with jackstands by frame. Remove front wheels. Remove axle nuts. Remove lower balljoint nut. Separate balljoint from nuckle by banging hard with ball peen hammer on knuckle on spindle assy. Remove outer tie-rod nut. Separate tie-rod from steering nuckle by bangin on nuckle with ball-peen hammer. Use long pry bar to hold lower control arm down while simultaneously pulling hub/spindle assembly away from vehicle and pushing axle through hub toward transaxle. Go under vehicle and pry inner cv joint away from transaxle while holding axle assembly.
Install new CV axle in reverse of the disassembly.

Feb 21, 2010 | 1997 Honda Accord

1 Answer

Cvc to motor

Yes. You will not be able to get the motor out unless you remove the axle

Apr 01, 2009 | 1993 Chevrolet Cavalier

2 Answers

Have a 2001 Buick LeSabre. Vibration turning left . Think it may be CV Joint. How do I pull the axle out to check CV Joint?

Rasie vehicle, remove tire, axle nut and caliper. remove tie rod end from spindle, remove lower ball joint nut and seperate from spindle and pull spindle from axle, with pry bar pop axle out of trans housing. it is easyer to replace cvc axle than to replace or repair cvc joint.

Nov 29, 2008 | 2001 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides