Question about 2002 Chevrolet Venture Passanger

Open Question

Replacing front axel on a 2002 chevy venture on the passenger side

I dont know how to reove the axel from the transmission end

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 14 Answers

SOURCE: Chevy Venture Passenger side windo won't roll up

wiring harness on passenger door has a severed wire

Posted on Mar 15, 2009

  • 1986 Answers

SOURCE: Im trying to replace the passenger mirror, need to

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Once the panel is off, you will see two or three bolts securing the mirror assembly onto the door

Posted on Sep 21, 2009

Testimonial: "Thank you so much. I just wasnt sure were the bolts were inorder to get off. That helped me a lot thanks!!! "

  • 468 Answers

SOURCE: Need to replace front brake pads on a 2002 chevy

Support the vehicle on jack stands or equivelant...block, rock, etc, remove the tires that you'll be working on. There will be two allen bolts on the back side of the caliper; remove those without twisting off the rubber boot that's attached to them. once you have those out, grab the caliper and pull it toward you to compress the cylinder. You may have to take some fluid out of the brake fluid reservoir so it doesn't overflow when you do this. Once you have the caliper piston compressed, lift it up, remove the pads, and replace them with the new ones. Your rotors usually don't really need replacing unless they have deep grooves worn in them, or the brake pedal vibrates when you are braking. Once you have the new pads in, put everything back like it was before you started taking it apart, and you're done with that wheel.

Posted on Nov 28, 2009

grendelynn
  • 5 Answers

SOURCE: fault code p0440 CHevy venture

I had that exact code a couple weeks ago. Mine needed new oxygen sensors. They(there are 2, only one was throwing a code, but I had both replaced) cost a little over $100 to have replaced.

Posted on Apr 23, 2010

iambanshee74
  • 3489 Answers

SOURCE: replacing a 2002 Chevy Venture front wiper motor

Look online for the wiper module for this model. This is a common issue to include operation without the switch being activated. Everything is controlled by the module which screws directly on the front of the wiper motor by 3 torx head screws and measures about 4" x 4" and is very easy to install. The motor should be on the firewall. The modules run anywhere between $35 and 65. Let me know if you need anything else.

Posted on Jul 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace passenger side glass on both doors


Remove interior door panels and unbolt the window mechanisms. It should be obvous once you ahve the panels off. Study online how to reove the door panels.

Feb 04, 2014 | 2002 Buick LeSabre

1 Answer

Size of nut on 2002 front wheel axel


need to now the vehicle 1st 2002 what?

Jun 09, 2012 | Cars & Trucks

1 Answer

How do u remove the passenger moror mount bracket on a 2002 chevy venture lt


Do you mean motor mount bracket? I would also assume that you mean the bracket that loops around the front of the engine on the right side of the vehicle - around the oil pan?
If this is what you mean, all I have to say is HAVE FUN! Those can be extremely hard to get off when you are in the shop with all the correct lifting equipment.

You must remove the air conditioning compressor from the front to get to those bolts and the only way to get the bolts on the other side is with an open-end wrench and a LOT of patience. The only thing harder than removing those bolts from between the engine and transmission housing is trying to get them started back in.

Apr 14, 2012 | 2002 Chevrolet Venture Passanger

1 Answer

Chevy venture hard shifting,door locks not working


by error code torch clutch seloined stuck on.Good luck-another product like the headlamps fogging over within a year and rear taillights problem.If you design something make it right the first time.Part seloined on tranny 19.00 labor 400.00.Also connectors below carpet on passengers side corrode and keeps messing up electrical like power lock doors not working abs sensors on front axels go bad easily.Rocker panels rust like rats eating cheese

Jun 26, 2011 | 1999 Chevrolet Venture

2 Answers

I have a 2003 chevy venture van 3.4 V6 I need to know where #1 spark plug is located on the engine


Number one on a V6 is on the end that drives the alternator. One bank is closer to that end. So passengers side, front of car.

Jun 09, 2011 | 2003 Chevrolet Venture Passanger

2 Answers

I want to know how to replace the axel on the front passenger side - the car is a '91 Subaru Loyale, manual transmission, front wheel drive


easy,just take the outer tie rod end nut off,cv axle nut and strut bolts,swing it out,some you might have allen head bolts at the tramnsmission also,very easy job.








Tim

Oct 21, 2010 | 1991 Subaru Loyale

1 Answer

1992 chevy k2500 4 wheel drive not engaging. was driving in 4 high with no problems. shut truck off and no 4wd. no lights and no 4wd. new rear end, new transmission.


I have a 19934x4 bought it with 4 wheel drive notworking. indicator lights for 4x4 would notlight up but transfer seemed to be shiftin ok. frontaxel woul ot ingauge. I repled the front axel actuator an works fine now no problem. actuator is on the passenger sid back of the front axel pigand has a plug, mine was 2 wireroundpin plug but some have a flat pin 4 wire plug. 70 dollars at NAPA. wasa realy simple replacement didnt even need to jack up the truck. the actuator h a pin that electronically puses out engauging te front axel. a easy test is to put the truck in 4 wheel high. holdthe brak and givei little gas ad havesomeoneelse stand to the side ofthe front of the truck and see if the front axel spins. ifso th actutor is te most likely prblem. hope this helps.

Dec 11, 2009 | 1993 Chevrolet K2500

1 Answer

2002 chevy trailblazer, replacing the transmission lines


the are located behind the dipstick on the passenger side of the transmission, you must remove the retainer clips and pull straight out the same as to the radiator. You may beed to remove the heat shield on the side of the transmission to ease acces

Sep 26, 2009 | 2002 Chevrolet TrailBlazer

Not finding what you are looking for?
2002 Chevrolet Venture Passanger Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...