Question about 2010 Chevrolet Equinox

Open Question

Where is the hazard flasher on a 2010 chevy equinox

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 7353 Answers

SOURCE: Where is the oil filter on the 2010 Chevy Equinox 2.4 Liter?

should be in front of engine lf side, it has a round cap, about 2.5-3 inches around with a hex top, to fit a socket on it, its a cartridge type.

Posted on Oct 17, 2009

Testimonial: "Thanks for your help. I found it in the front of the engine closer to the driver side. Uses a 32 mm socket. "

  • 30 Answers

SOURCE: 2010 cabin air filter

It is located underneath the hood on the passenger side, underneath the plastic vent cover, just below the Windshield. Pretty easy to change yourself. The filters tend to get pretty dirty pretty Fast on the Equinox

Posted on Apr 21, 2010

  • 14585 Answers

SOURCE: Hello, Trying to find the DRL

If you have one it's under the dash to the left side of the steering column. I don't know if chevy has done it yet, but ford removed the module and stuck the electronics in the instrument panel

Posted on Feb 09, 2011

  • 2 Answers

SOURCE: How do u take off

If it has a trunk see if there is an access panel in there. My hyundai has one in the trunk.

Posted on Feb 16, 2011

  • 188 Answers

SOURCE: keys stuck in ignition chevy

If the key is stuck in the ignition and cannot be removed, I would assume that the suv is still under warranty at the dealer. I would consult with them first.

Posted on Feb 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you locate and test flasher relay on a 2006 Chevy Equinox? Turn signals and hazards stopped working after changing audio system. Fuses test good. Thank you, Mike


Did you change any wiring , tap into any wiring ? There is no flasher relay on your vehicle . It controlled by the BCM !
Turn Signal/Hazard Lamps
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.
Your best bet , take it to a qualified repair ! We on here have no clue what you did . On this newer vehicles ,if you know nothing about automotive electronics you really should take to a professional

Aug 10, 2017 | Cars & Trucks

1 Answer

Emergency flasher switch


The Hazard Warning flasher switch is located in the center of the instrument panel above the radio. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off the Hazard Warning flasher. This is an emergency warning system and should not be used when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. When you must leave the vehicle to seek assistance, the Hazard Warning flasher will continue to operate even though the ignition switch is OFF. NOTE: With extended use, the Hazard Warning flasher may wear down your battery. http://cdn.dealereprocess.com/cdn/servicemanuals/chrysler/2010-townandcountry.pdf

Nov 26, 2015 | 2010 Chrysler Town and Country

2 Answers

I would like to replace the stock turn signal bulbs with LEDs; I need to find and replace the turn signal flasher/relay


It's usually under the dash on the driver's side area. What vehicle are you asking for?

Apr 04, 2015 | Cars & Trucks

1 Answer

Where is the hazard light switch on a 2010 Chevy equinox


There is a button with an arrow pointing up right above the heat & air condition buttons . There should be symbols that look like locks beside it. That's the hazard light switch.

Jun 17, 2014 | 2010 Chevrolet Equinox

3 Answers

Where does the flasher go on a 98 chevy malibu


Replacement The turn and hazard flashers are integrated into one flasher on these models. The flasher is located in the hazard warning switch and the hazard warning switch is located on the trim plate. Replace the flasher by unplugging the old one, removing it from the panel, and plugging in the new one.
  1. Remove the bezel from the ignition switch.
7f58edd.gif
Remove the bezel from the ignition switch

Carefully remove the instrument panel accessory trim plate.

9f5c3cc.gif
To remove the trim plate, use a suitable prytool to carefully apply pressure at the retaining clip points . . .

bd28884.gif
. . . then gently pull the accessory trim plate away

Detach the electrical connector from the hazard warning switch.

daa6205.gif
Unplug the electrical connector from the hazard warning switch . . .

Unfasten the screw securing the hazard warning switch and remove the switch.

c506713.gif
. . . then unfasten the screw securing the hazard warning switch and remove the switch from the vehicle


Installation is the reverse of removal.

Dec 01, 2009 | 1998 Chevrolet Malibu

1 Answer

Blinkers in a 1987 chevy camaro not working inside or out. what might the problem be?


Have you checked the signal light flasher?
You have one for the hazard flashers and one for the turn signals.
Try the hazard flashers.
If they work....switch that flasher with the signal flasher....(they should be interchangeable).
Follow the clicking sound to find the hazard (working ) flasher.
(It just pulls out )
To find the non working signal light flasher....just look for another flasher under the dash that looks very much like the hazard flasher.
Now try the signal lights again with the different flasher installed....do they work now?

Sep 14, 2009 | 1987 Chevrolet Camaro

Not finding what you are looking for?
2010 Chevrolet Equinox Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...