Question about 2004 Ford F350

Open Question

Ford f350 brake line replace - 2004 Ford F350

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 7353 Answers

SOURCE: Broken Brake line at the bend

rusted or broken? if its broken thats a design flaw. you should be able to route new line without dropping fuel tank.

Posted on Oct 14, 2009

  • 2428 Answers

SOURCE: broken brake line in drivers side rear 1997 ford

You can fix this but you need some specical tools You need a tubeing cutter and a flaring tool you can buy sections of brake line im not suppose to name stores but it begins with an N and ends with an A cut the line back to a point where its sound its easyer if you can remove the other end at a fitting then you;ll olny have to make one flare under the vehicle the flareing tool is about 30 dollars and the tubeing cutter is around 5 -10 dollars thr line is cheap You need to flare the old line to make it work with the new fitting you can;t use compression fittngs there not legal and won;t work if you have a problem getting the fitting end of at the rear wheel try hitting it with a propane torch for a few seconds not to long don;t start a fire or melt your rear wheel cylinder The instructions for the flareing come with the tool don;t try to dubble flare its not nessary but this will be a perminate fix and all you have to do is bleed the rear drivers side wheel cyinder good luck

Posted on Nov 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 Ford F 350 4X4 Diesel. Brake pedal goes to


You need to crawl under the truck and inspect each brake line for leaks. You also need to check wheel cylinders and calipers. The chances are pretty good that you will find a small leak in a line or a wheel cylinder leaking, pay close attention to the rear of the truck because that is normally where these problems occur. Hope this helps.

Jul 10, 2010 | 1994 Ford F350 Crew Cab

1 Answer

1997 F350 diesel brakes just quit working and simultaneously the engine started clicking??? Any clues?


I would look at the brake booster line. I have the same truck and it was the vacumn line off the booster.

Jan 11, 2010 | 1997 Ford F350 Crew Cab

1 Answer

Broken Brake line at the bend


rusted or broken? if its broken thats a design flaw. you should be able to route new line without dropping fuel tank.

Oct 14, 2009 | 1999 Ford F350 Regular Cab

2 Answers

Hi. I have a 1990 Ford F350 diesel UHaul with no


when you replace the master cylinder, your are supposed to pump it up manually before you install it. If you don't, you'll have to sit there and pump the brake pedal a couple of thousand times as one almost microscopic air bubble at a time escapes the pressure tube and back fills with fluid. once you can push the pedal repeatedly without any bubbles escaping into the reservoir, then bleed the brakes. Starting with the farthest, usually the Right Rear and work your way up. Make sure you keep the fluid level topped off. If it sucks air once, you have to start all over.

Sep 23, 2009 | 1990 Ford F350

1 Answer

Brake peddle hits the floor when engine turned on


did you set up the brakes make sure that it is set

Aug 08, 2009 | 1997 Ford F350 Crew Cab

1 Answer

2002 ford f350 deisel brakes pedal feels hard and dosnt stop verry good well driving. Brakes smell like they are burning when I stop. Just replaced front rotors,pads and calipers


You should have a hydraulic brake booster. a common failure item on fords and also would cause your symptom. the burning smell, I would go back and recheck all the brakes. Maybe a problem with the e-brakes, or an issue with the front or rear calipers. Possibly a damaged steel or high pressure brake line. Good luck.

Apr 26, 2009 | 1996 Ford F350 Crew Cab

1 Answer

Master cylinder won't come off 2001 F350


if its just the master cylinder then there are 2 bolts and the lines and thats it. you might have to tap it a little do to rust or because it sticks over time. if its the master cylinder and the brake booster then you will have to disconnect the booster from the brake pedal on the inside

Nov 30, 2008 | 1997 Ford F350 Crew Cab

1 Answer

1993 F350 ABS light


i had a problem with my abs light one night i had a brake line behind the driver front tire broke and it was leaking out all of the fluid and the abs light came on i replaced the line and filled up the master cylinder and it went away so check your lines and master cylinder

Aug 18, 2008 | 1993 Ford F350

Not finding what you are looking for?
2004 Ford F350 Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...