Question about Honda Cars & Trucks

Open Question

Honda pilot coolant crossover pipe gaskets - Honda Cars & Trucks

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2000 f150 ford coolant crossover problems 5.4 liter engine

sitting timimg chain on 2000 f150 5,4

Posted on Jan 28, 2009

iambanshee74
  • 3489 Answers

SOURCE: Will a leak in the coolant crossover pipe cause my

no. a leaking headgasket or intake manifold will however.

Posted on Nov 02, 2009

  • 1810 Answers

SOURCE: gaskets needed to change a coolant crossover pipe

huge

Posted on Mar 26, 2010

  • 14036 Answers

SOURCE: I have a leaking coolant crossover pipe on an '02

GO TO AUTO ZONE OR ADVANCE AUTO PARTS BUY A HAYNES REPAIR MANUAL.IT WILL HELP.

Posted on Jun 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Having a promblem taking off crossover exhaust pipe on a 2005 Buick rendezvous I tooken off the two front exhaust Then took bottom two bolt . But still fasten to something is there other bolts...


Thermostat? engine cooling?
2 engines, here, LYA adn LY7.
nobody here posts engine, why do that?
so ill post only for 1.
the LA1
here are the steps.
NO FSM Sux huh? nor an alldata.com account, why not that? 15 bucks?


STAT out.
Remove the air cleaner and duct assembly. Refer to Air Cleaner Assembly Replacement in Engine Controls - 3.4L.

Drain the coolant until the coolant level is below the thermostat. Refer to Cooling System Draining and Filling (Refer To List 1) .

Remove the crossover exhaust pipe. Refer to Exhaust Crossover Pipe Replacement (Refer To List 2) in Engine Exhaust.

Remove the radiator hose from the thermostat housing.

Remove the thermostat housing bolts and clean any sealer from the bolt threads.

Remove the thermostat housing and gasket.
remove STAT
next is crossover page.

Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnection and Connection (Refer To List 1) in Engine Electrical.

Remove the throttle body air inlet duct.

Drain the coolant from the cooling system. Refer to Cooling System Draining and Filling (Refer To List 2) in Engine Cooling.

Remove the inlet radiator hose from the engine. Refer to Radiator Inlet Hose Replacement (Refer To List 3) in Engine Cooling.

Remove the thermostat bypass pipe. Refer to Thermostat Bypass Pipes Replacement in Engine Cooling.



Remove the exhaust crossover heat shield bolts.

Remove the exhaust crossover heat shield.
  1. Remove the exhaust crossover pipe studs/nuts.
  2. Remove the exhaust crossover pipe.

end , remove.

now the bypass pipe FWD cars SUCK
  1. Disconnect the left engine mount strut from the engine.
  2. Remove the heater hose from the bypass pipe.
  3. Remove the thermostat bypass pipe to throttle body nut.
  4. Use the J 38185 in order to remove the thermostat bypass pipe hose clamps (1,5).
  5. Remove the thermostat bypass pipe to cylinder head nut (3).
  6. Remove the thermostat bypass pipe bolt (4).
  7. Remove the thermostat bypass pipe hose.
  8. Remove the thermostat bypass pipe.
sigh.....
why not log in to alldata.com
read the page then ask ques tons that are not clear.
and next time post the engine type.
above is just 1 engine.

Jun 18, 2014 | Cars & Trucks

1 Answer

My husband and I are trying to get to our thermostat to change in my 2002 rendezvous, but there is a metal pipe in the way that we can't figure out how to remove. just behind the pipe, is a metal plate...


Hello vocalviixen,

The pipe that you referred to is the exhaust crossover pipe. Below I've included removal and installation instructions.

Also, the procedure for bleeding the coolant system is critical; if you need those instructions please post the question.

REMOVAL PROCEDURE
1. Disconnect the battery ground (negative) cable.
2. Remove the throttle body air inlet duct.
3. Drain the coolant from the cooling system.
4. Remove the inlet radiator hose from the engine.
5. Remove the thermostat bypass pipe.
6. Remove the exhaust crossover heat shield bolts.
7. Remove the exhaust crossover heat shield.
8. Remove the exhaust crossover pipe studs/nuts.
9. Remove the exhaust crossover pipe.
INSTALLATION PROCEDURE
1. Install the exhaust crossover pipe.
2. Install the exhaust crossover pipe studs/nuts.
3. Tighten the exhaust crossover pipe studs/nuts to 18 lb ft.
4. Install the exhaust crossover heat shield.
5. Install the exhaust crossover heat shield bolts.
6. Tighten the exhaust crossover heat shield bolts to 89 lb in.
7. Install the thermostat bypass pipe.
8. Install the inlet radiator hose to the engine.
9. Fill the cooling system with engine coolant.
10. Install the throttle body air inlet duct.
11. Connect the battery ground (negative) cable.


Regards,
netvan

Mar 14, 2011 | 2002 Buick Rendezvous

1 Answer

Thermostat replacement 2002 rendezvous


Thermostat Removal & Installation 3.4L & 3.5L Engine To Remove:
  1. Drain the coolant below the level of the thermostat.
  2. Remove the air cleaner and duct assembly.
  3. Remove the exhaust crossover pipe.
  4. Disconnect the radiator hose from the thermostat housing. gm_mv_ven_tstat.gif

  5. Remove the mounting bolts and remove the thermostat housing.
  6. Remove the housing gasket.
  7. Remove the thermostat.
  8. Clean the mating surfaces.
To Install:
  1. Install the thermostat on the engine. NOTE: Apply RTV sealer to the thermostat housing bolt threads.
  2. Install the thermostat housing and gasket with the mounting bolts. Tighten 18 ft-lb (25 Nm).
  3. Connect the radiator hose to the thermostat housing.
  4. Install the exhaust crossover pipe.
  5. Install the air cleaner and duct assembly.
  6. Fill the cooling system.
  7. Check the cooling system for leaks.
3.6L Engine To Remove:
  1. Remove the air cleaner.
  2. Remove the throttle body.
  3. Remove the heater pipes.
  4. Remove the coolant inlet pipe. Thermostat 3.6L gm-03-36-2447.gif

  5. Remove the thermostat mounting bolts and remove the thermostat.
  6. Clean the thermostat and heater pipe mating surfaces.
To Install:
  1. Place the thermostat in the housing with a new gasket.
  2. Install the thermostat and gasket on the engine with the mounting bolts. Tighten 89 in-lb (10 Nm).
  3. Install the coolant inlet pipe.
  4. Install the heater pipes.
  5. Install the throttle body.
  6. Install the air cleaner.
  7. Fill the cooling system and perform a leak test.
prev.gif next.gif

Dec 19, 2010 | 2002 Buick Rendezvous

1 Answer

Remove thermostat


Thermostat Removal & Installation To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Partially drain the coolant, (until the level is below the thermostat).
  3. Remove or disconnect the following:
    • The air cleaner and duct assembly
    • The crossover exhaust pipe
    • The radiator hose from the thermostat housing
    • The thermostat housing bolts
    • Any remaining sealer from the bolt threads gm_mv_ven_tstat.gif

    • The thermostat housing
    • The gasket
    • The thermostat
To Install:
  1. Install or connect the following:
    • The thermostat
    • The thermostat housing
    • The gasket NOTE: Apply RTV sealer, GM P/N 1052366 or the equivalent, to the thermostat housing bolt threads.
    • The thermostat housing bolts
      1. Torque to: 18 ft. lbs. (25 Nm)
    • The radiator hose to the thermostat housing
    • The crossover exhaust pipe
    • The air cleaner and duct assembly
    • The coolant
  2. Thoroughly inspect the cooling system for leaks.
prev.gif next.gif

Dec 15, 2010 | 2005 Pontiac Montana

1 Answer

Change theromstat 2003 chevy venture


Thermostat Removal & Installation To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Partially drain the coolant, (until the level is below the thermostat).
  3. Remove or disconnect the following:
    • The air cleaner and duct assembly
    • The crossover exhaust pipe
    • The radiator hose from the thermostat housing
    • The thermostat housing bolts
    • Any remaining sealer from the bolt threads gm_mv_ven_tstat.gif

    • The thermostat housing
    • The gasket
    • The thermostat
To Install:
  1. Install or connect the following:
    • The thermostat
    • The thermostat housing
    • The gasket NOTE: Apply RTV sealer, GM P/N 1052366 or the equivalent, to the thermostat housing bolt threads.
    • The thermostat housing bolts
      1. Torque to: 18 ft. lbs. (25 Nm)
    • The radiator hose to the thermostat housing
    • The crossover exhaust pipe
    • The air cleaner and duct assembly
    • The coolant
  2. Thoroughly inspect the cooling system for leaks.
prev.gif next.gif

Nov 05, 2010 | 2004 Chevrolet Venture Passanger

1 Answer

What do i do when its over heating? how do i install thermostat?


Thermostat Removal & Installation 3.4L & 3.5L Engine To Remove:
  1. Drain the coolant below the level of the thermostat.
  2. Remove the air cleaner and duct assembly.
  3. Remove the exhaust crossover pipe.
  4. Disconnect the radiator hose from the thermostat housing. gm_mv_ven_tstat.gif

  5. Remove the mounting bolts and remove the thermostat housing.
  6. Remove the housing gasket.
  7. Remove the thermostat.
  8. Clean the mating surfaces.
To Install:
  1. Install the thermostat on the engine. NOTE: Apply RTV sealer to the thermostat housing bolt threads.
  2. Install the thermostat housing and gasket with the mounting bolts. Tighten 18 ft-lb (25 Nm).
  3. Connect the radiator hose to the thermostat housing.
  4. Install the exhaust crossover pipe.
  5. Install the air cleaner and duct assembly.
  6. Fill the cooling system.
  7. Check the cooling system for leaks.
3.6L Engine To Remove:
  1. Remove the air cleaner.
  2. Remove the throttle body.
  3. Remove the heater pipes.
  4. Remove the coolant inlet pipe. Thermostat 3.6L gm-03-36-2447.gif

  5. Remove the thermostat mounting bolts and remove the thermostat.
  6. Clean the thermostat and heater pipe mating surfaces.
To Install:
  1. Place the thermostat in the housing with a new gasket.
  2. Install the thermostat and gasket on the engine with the mounting bolts. Tighten 89 in-lb (10 Nm).
  3. Install the coolant inlet pipe.
  4. Install the heater pipes.
  5. Install the throttle body.
  6. Install the air cleaner.
  7. Fill the cooling system and perform a leak test.
prev.gif next.gif

Sep 18, 2010 | 2002 Pontiac Aztek

1 Answer

Replacement of thermostat 2001 alero


Thermostat replacement on 3.4 liter, Not the thermostat housing is between the Throttle body and exhaust crossover. If you have small haves and the right tools you can remove the two botls without removing the crossover and throttle body. The bottom bolt to the thermostat does not have to come all the way out, there is a cut out on the housing so you can slid it out. Good luck and take your time.

  1. Remove the air cleaner and duct assembly.
  2. Drain the coolant until the coolant level is below the thermostat.
  3. Remove the crossover exhaust pipe.
  4. Remove the radiator hose from the thermostat housing.
  5. Remove the thermostat housing bolts and clean any sealer from the bolt threads.
  6. Remove the thermostat housing and gasket.
  7. Remove the thermostat.
  8. Install the thermostat.
  9. Install the thermostat housing bolts and tighten them to 18 ft. lbs. (25 Nm).
  10. Install the radiator hose to the thermostat housing.
  11. Install the crossover exhaust pipe.
  12. Install the air cleaner and duct assembly.
  13. Good luck...
  14. Fill the cooling system.
  15. Install the thermostat housing and gasket.
  16. Clean the mating surfaces.

Jan 28, 2010 | 2001 Oldsmobile Alero

1 Answer

How do i change my thermostat on my 2001 pontiac aztek. also how do i remove the crossover exhaust pipe to get to the @#$%^ing thing?


Exhaust Crossover Pipe Replacement
Removal Procedure
  1. Disconnect the battery ground (negative) cable.
  2. Remove the throttle body air inlet duct.
  3. Drain the coolant from the cooling system.
  4. Remove the inlet radiator hose from the engine.
  5. Remove the thermostat bypass pipe.
  6. Remove the exhaust crossover heat shield bolts.
  7. Remove the exhaust crossover heat shield.
89160026

  1. Remove the exhaust crossover pipe studs/nuts.
  2. Remove the exhaust crossover pipe.
  1. Remove the air cleaner and duct assembly.
  2. Drain the coolant until the coolant level is below the thermostat.
  3. Remove the crossover exhaust pipe.
  4. Remove the radiator hose from the thermostat housing.
  5. Remove the thermostat housing bolts and clean any sealer from the bolt threads.
  6. Remove the thermostat housing and gasket.
Removal Procedure

89153578

Dec 11, 2009 | 2003 Pontiac Aztek

1 Answer

Have heating problem thermostat replaced


Thermostat replacement on 3.4 liter, Not the thermostat housing is between the Throttle body and exhaust crossover. If you have small haves and the right tools you can remove the two botls without removing the crossover and throttle body. The bottom bolt to the thermostat does not have to come all the way out, there is a cut out on the housing so you can slid it out. Good luck and take your time.

  1. Remove the air cleaner and duct assembly.
  2. Drain the coolant until the coolant level is below the thermostat.
  3. Remove the crossover exhaust pipe.
  4. Remove the radiator hose from the thermostat housing.
  5. Remove the thermostat housing bolts and clean any sealer from the bolt threads.
  6. Remove the thermostat housing and gasket.
  7. Remove the thermostat.
  8. Install the thermostat.
  9. Install the thermostat housing bolts and tighten them to 18 ft. lbs. (25 Nm).
  10. Install the radiator hose to the thermostat housing.
  11. Install the crossover exhaust pipe.
  12. Install the air cleaner and duct assembly.
  13. Good luck...
  14. Fill the cooling system.
  15. Install the thermostat housing and gasket.
  16. Clean the mating surfaces.

Nov 11, 2009 | 2001 Oldsmobile Alero

1 Answer

Themostat


Nevermind...it doesn't matter....here ya go....please don't forget to rate!!!

Thermostat Removal & Installation To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Partially drain the coolant, (until the level is below the thermostat).
  3. Remove or disconnect the following:
    • The air cleaner and duct assembly
    • The crossover exhaust pipe
    • The radiator hose from the thermostat housing
    • The thermostat housing bolts
    • Any remaining sealer from the bolt threads
987d698.gif
  • The thermostat housing
  • The gasket
  • The thermostat
  • To Install:
    1. Install or connect the following:
      • The thermostat
      • The thermostat housing
      • The gasket NOTE: Apply RTV sealer, GM P/N 1052366 or the equivalent, to the thermostat housing bolt threads.
      • The thermostat housing bolts
        1. Torque to: 18 ft. lbs. (25 Nm)
      • The radiator hose to the thermostat housing
      • The crossover exhaust pipe
      • The air cleaner and duct assembly
      • The coolant
    2. Thoroughly inspect the cooling system for leaks.

    Apr 05, 2009 | 2001 Pontiac Montana

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    307 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    yadayada
    yadayada

    Level 3 Expert

    75197 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7782 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...