Question about 2004 Hyundai Elantra

Open Question

How do you change the oil control valve 2005 hyundai

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 12 Answers

SOURCE: oil control valve

You mention the oil control valve,so you have a 2 litre petrol engine with cvvt then?Sometimes you can remove the oil control valve and clean it out and re install it and an oil change with nice clean oil is good for them too.The ocv valve is located when plastic engine cover is removed,on the front rh top of the cyl head with an electrical plug on it.

Posted on Feb 17, 2009

michigan man
  • 3533 Answers

SOURCE: oil change procedure on a 2005 Hyundai elantra

it is very easy to change the oil put the car on ramps secure the back end look for the drain plug underneath the engine make sure you have the right size wrench and when you remove the plug also check the gasket on the plug to make sure it is not cracked you will also need an oil filter wrench and my other suggestion to you is to go to autozone to see if they have a Haynes repair manual for your car and if they don't see if they can order you one in the mean time they can also print you off a diagram of how to change the oil in you car safely

Posted on Jan 20, 2009

ecmurphy10
  • 53 Answers

SOURCE: oil change procedure on a 2005 Hyundai elantra

This one is simple

1. Remove dip stick and filler cap.
2. Remove oil plug from oil pan and drain oil into an appropriate pan.
3. Remove and replace oil filter. (Filter will drain oil, just be aware to try and get it into the pan.
4. Refill oil. Start with 3.5 quarts, put cap and dip stick back on and start car, wait about 10 seconds and then turn off.
5. Check your dipstick for proper oil level.

And thats it you are done.

Posted on Jan 20, 2009

  • 2 Answers

SOURCE: oil control valve

on the lower front of the cyl head right where the thermostat is a 14 mm bolt remove that bolt and there will be a screen filter for the ocv if clogged it will reduce oil pressure to the ocv and give you a p0010 or p0011 code clean screen replace clear code all should be good

Posted on Jun 22, 2009

skychief2001
  • 21873 Answers

SOURCE: Can anyone help...i need to change out my proportioning valve on 2005 Hyundai Sonata. I don't know were it is can you tell me.

Its usually part of the master cylinder.

Posted on Oct 01, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hyundai slowly burning oil


Do a compression test to determine if the piston rings are worn. Bad valve stem seals will allow excessive oil to be drawn by the valve stem guides.

Oct 22, 2015 | 2005 Hyundai Accent

1 Answer

How do i locate oil control valve on a 2009 hyundai santa fe


What type of oil control valve??
Oil pressure on cars is unregulated and oil is not turned on and off so what control valve??

Feb 13, 2015 | Hyundai Cars & Trucks

1 Answer

Is a fuel filter and a oil control value the same thing


no its not, the fuel filter cleans the gas leaving your tank going into your injectors [important to change yearly] the oil control valve ??? the only one i know of is on your oil pump called a bypass valve .Spring and ball bearing stops over preasure if say your oil filter clogged or your oil channels plugged ??

Nov 07, 2013 | 2004 Hyundai Elantra

1 Answer

I just had my oil changed last week at Superlube and now my engine light is on and give code P0011 for my 2007 Hyundai Sonata, does anyone know if the oil change could have caused this?


Inspect your oil control valve, disconnect it and read the ohms resistance, specs 6.9-7.9. If is not in specs replace it. it is possible oil change caused it, TIP: after market filter will cause engine damage,

Mar 12, 2013 | Hyundai Sonata Cars & Trucks

1 Answer

I brought a car and mileage in odometer is wrong


ignore the electrical problem its a second hand motor end of story ,now change the oil every 6000kms with a oil filter every every third oil change and the engine will run forever ,use the cheapest oil you can buy from a supermarket ,Dont use the AC too much if you can help it as the front crankshaft pulley fixing isnt very good on these engines and excessive use of the Ac will result in the keyway wearing out and the timing going out then the valves start touching the pistons and as it gets worse then the valves bend and it bangs like drums in the notting hill carnival .

Dec 28, 2012 | Cars & Trucks

1 Answer

Quest code p1136


P1136 NISSAN - Intake Valve Timing Control Solenoid Valve Circuit Bank 2
Possible causes- Intake valve timing control solenoid valve bank 2 circuit is open or shorted.
- Intake valve timing control solenoid valve bank 2 circuit connectors
- Intake valve timing control solenoid valve bank 2 Tech notes Since the Intake valve timing control solenoid valve uses oil flow to control timing, dirty oil can cause the valve to stuck open or close. Before replacing the valve, change engine oil and filter and reset engine code.

Aug 29, 2012 | 2005 Nissan Quest

1 Answer

Hyundai Tucson


The transmission filter is inside the transmission. You have to drain out the oil and remove the transmission pan and gasket. The filter is made of metal guaze and is screwed/bolted to the underneath of the valve body.

Apr 08, 2009 | 2005 Hyundai Tucson

2 Answers

Oil control valve


You mention the oil control valve,so you have a 2 litre petrol engine with cvvt then?Sometimes you can remove the oil control valve and clean it out and re install it and an oil change with nice clean oil is good for them too.The ocv valve is located when plastic engine cover is removed,on the front rh top of the cyl head with an electrical plug on it.

Dec 21, 2008 | 2004 Hyundai Elantra

Not finding what you are looking for?
2004 Hyundai Elantra Logo

Related Topics:

284 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...