Question about Dodge Cars & Trucks

Open Question

How to remove intermediate shaft 2002 dodge ram

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: how to remove the left axle on 97 odyssey

yes, the left (driver) side pops off similar to the right side, however, it just pops off of the intermediate shaft instead of the transaxle. for some reason the first time i had tried it, it would not move. later when i tried it again it came off easily. go figure!

Posted on Jan 19, 2009

Ad
  • 45 Answers

SOURCE: removing the right intermediate axle shaft

i can only guess it is a 3.0l 4v well as far as the axle goes, the rh outer half shaft seperates at the splines on the intermediate shaft.
the intermediate shaft is the solid shaft from the trans to a bearing support bracket and ends after that. it is externally splined.
the rh axleshaft , inner cv joint, is internally splined.
to remove the rh axleshaft, remove the rh wheel and splash shield.
removed the lower balljoint pichbolt and seperate the lower balljoint front the steering knuckle. take the axle nut off and using a large brass drift or hardwood, drive the axle out of the bearing-hub assembly. DO NOT DAMAGE THE THREADS. also use some lubricant on the axle nut dissasembly. after the outer axle end is free, using the same brass drift or other, hit the inner cv joint and drive it off the intermediate shaft. inspect the splines closely because these fail and cause a no-drive condition.
then the mounint bolts for the support bearing and pull the intermedate shaft out, you will loose some fluid.

Posted on Jan 28, 2009

  • 2 Answers

SOURCE: Intermediate Steering Shaft

clunking coming from steering cloume left or right turns, car not moving! they say I can lube it, where?

Posted on Jun 14, 2009

  • 17 Answers

SOURCE: 2001 Ram 1500 Truck 2WD: how do you remove a tail light from a 2002 dodge r...

There are for Philip screws holding your tail light cover onto your dodge. Step 1: Just remove those screws and pull the cover off. Step 2: Remove the light bracket out of the cover and replace with a 1057 bulb.

Posted on Jun 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace steering wheel position sensor on a 2006 Cadillac DTS?


Manual Steering Column with JL4) or
Steering Wheel Position Sensor Replacement (Power Steering Column with JL4) ?
Preliminary Procedure Remove the intermediate steering shaft. Refer to Intermediate Steering Shaft Replacement .
1
Steering Angle Sensor Adapter
2
Steering Wheel Position Sensor
Procedure Disconnect any electrical connectors as needed.
Tip
If reusing, secure the old steering wheel position sensor before removing it for proper alignment upon reinstallation. Refer to Steering Wheel Position Sensor Centering .

Callout

Component Name
Notice: Secure the steering wheel utilizing a strap to prevent rotation. Locking of the steering column will prevent damage and a possible malfunction of the SIR system. The steering wheel must be secured in position before disconnecting the following components:
?€¢
The steering column
?€¢
The intermediate shaft
?€¢
The steering gear

After disconnecting these components, do not move the front tires and wheels. Failure to follow these procedures may cause improper alignment of some components during installation and result in possible damage to the SIR coil.
Preliminary Procedure Remove the steering column. Refer to Steering Column Replacement .
1
Intermediate Steering Shaft Bolt
Procedure Remove the steering column boot seal in order to access the intermediate steering shaft bolt.
2
Intermediate Steering Shaft Nut
Notice: Refer to Fastener Notice in the Preface section.
Tighten
47 N?·m (35 lb ft)
3
Intermediate Steering Shaft
Tip
?€¢
If necessary, scribe location marks between the intermediate steering shaft and the steering column and the intermediate steering shaft and the steering gear to mark their alignment before removing.
?€¢
If replacing the intermediate steering shaft, transfer any scribe marks from the old one to the new one.

Callout

Component Name
Notice: Secure the steering wheel utilizing a strap to prevent rotation. Locking of the steering column will prevent damage and a possible malfunction of the SIR system. The steering wheel must be secured in position before disconnecting the following components:
?€¢
The steering column
?€¢
The intermediate shaft
?€¢
The steering gear

After disconnecting these components, do not move the front tires and wheels. Failure to follow these procedures may cause improper alignment of some components during installation and result in possible damage to the SIR coil.
Preliminary Procedures

  1. Remove the left side instrument panel insulator panel. Refer to Instrument Panel Insulator Panel Replacement - Left Side .
  2. Remove the driver knee bolster. Refer to Driver Knee Bolster Replacement .
  3. Disconnect the intermediate steering shaft from the steering gear. Refer to Steering Gear Replacement .
1
Steering Column Nut (Qty: 4)
Notice: Refer to Title not found in the Preface section.
Tighten
25 N?·m (18 lb ft)
2
Steering Column
Procedure
  • Disconnect any electrical connectors as needed.
  • If equipped with AN3, disconnect the automatic transmission range selector cable. Refer to Automatic Transmission Range Selector Cable Replacement - Column .
  • Transfer any parts as needed.
  • Sep 12, 2015 | Cadillac Cars & Trucks

    1 Answer

    How do I replace my inner axle on the passenger side of my 2002 Dodge Ram 4x4 4.7L. I lent my truck out and the C clip let go of the CV axle. The intermediate axle spline is stripped and I need to change...


    Lift and support front end on suitable jack stands preferably on frame. Remove right front cv axle, stub shaft, and seal. You will need to pull the right front brake caliper assembly loose and place to the side. Then remove bolts from shock and upper control arm and hub nut to do this. Next, remove axle lock actuator on passenger side of front axle. Place a drain pan underneath front diff cover and remove cover and drain axle. In the center of differential there will be an 8 mm head bolt holding spider gear cross-shaft. Remove bolt and cross-shaft only! Push inner axle in until clip clears inside of passenger spider gear. Set clip aside and push/pull axle shaft straight out to passenger side.

    Feb 09, 2015 | Dodge Cars & Trucks

    1 Answer

    _i need to replace the intermediate shaft on the drivers side how do i get the old one out?


    Girlfriend had a New Yorker with an intermediate shaft, but like most of them it drove the front passenger side wheel. When it went out instead of trying to find another one, which I found you can't, I just bought the right side front drive shaft for the version of the car which did not have the intermediate shaft. The big Chrysler one step down from the New Yorker. So she had a standard left side drive shaft and much longer drive shaft for the passenger side. As I recall there was a small bracket which held the intermediate shaft bearing which had to be removed and discarded. It worked just fine until the rear axle beam rotted through, you can't find those either, and she had to junk it.

    Nov 09, 2010 | Dodge Ram 1500 Cars & Trucks

    1 Answer

    Reasons for "play" in a steering wheel. I have a 1998 dodge ram 1500 club cab and can turn my wheel almost 2" without the wheels turning. I had it looked at from a local garage and they found a broken sway...


    Could be more worn steering parts such as the pitman or idler arm. IIRC, the 98 Ram has a steering gear box, and not rack and pinion steering like newer models.

    If the issue is not up front under the hood, you could also have a worn intermediate (sometimes called a sector shaft) . This shaft goes between the steering column and the gear box or rack and pinion.

    Apr 18, 2010 | 1998 Dodge Ram 1500 4WD

    1 Answer

    Pops when turning the wheel


    Could be intermediate shaft, bad ball joints, or bad rack and pinion.

    Jul 10, 2009 | 2004 Dodge Ram 1500

    1 Answer

    1999 dodge cummins 2500 front axel seals


    you need to pull off wheels,brakes, rotor /unit hub bearing, both axles and intermediate shaft, as well as the vac disconnec ton the front axle tube. if only the right side leaks then only then only pull the right axle and intermediate shaft and vac disco. it is a trick with a miller tool to replace the seal. the left side seal is inside the diff and the carrier has to come out to replace it. pete

    Jun 09, 2009 | 2004 Dodge Ram 2500

    2 Answers

    Front hub bearing removal 2002 dodge ram 1500 4WD 4.7L V8


    i just did a 2002 2500 4x4 with a dana straight axle and had no problem getting on the bolts with a 9/16 12 point socket on a 6 inch extension. If you do not use an extension the head of the ratchet will hit the yoke of the axle shaft.

    Dec 07, 2008 | 1998 Dodge Ram 1500 4WD

    3 Answers

    1999 dodge ram 2500 4x4 front end drifts steering links between firewall and steering box moves a lot at joints is this normal?


    You need to have the play in the steering box repaired, that is most likely the cause of your problem.

    Jul 31, 2008 | 1983 Dodge Pickup

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    325 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...