Question about 2004 Chrysler Crossfire

Open Question

REMOVING DOOR MIRROR ON CHRYSLER CROSSFIRE

PASSENGER DOOR MIRROR

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
HansPP
  • 2510 Answers

SOURCE: Need to remove passenger front door inside door

You need to remove any screws that are in the vicinity if pull handles and door pockets. These screws will be under little covers that you need to prise off to get to their heads. The lock knob, if there is one there, will have to be screwed off and then carefully work your way around the door, freeing the panel's clips from their holes in the door frame. Finally the panel will probably have to be lifted out if the window slot (I take it that you have found all the screws around the edge of the panel and the latch release handle?) Disconnect any electrical plugs behind the panel. Under the panel you will find a plastic dust sheet that is stuck to the door frame, remove this carefully, you will have to replace it before replacing the panel.

Posted on Mar 04, 2011

Ad
  • 580 Answers

SOURCE: 2004 chrysler crossfire resetting service light

Disconnect negative battery post for 30 seconds & reconnect. This action will reset the car's computor & remove the light.

Posted on Jan 08, 2010

  • 120 Answers

SOURCE: replace front passenger window for 2000 chrysler cirrus

most windows follow the same proceedure...
lok careful at the door pad you will see screws hidden by the inside handle (usualy 1 door opener handle) sum screws are hidden by caps / lil round covers that u pry up with a small pick tool (2 usualy by the inside pull /grab handle) sum you pry up the door switchs and can be hidden underneith) sum may be on the edges , if the lil trim panel that covers the mirror mount (may also have speaker in it )is in the way they usualy pull straight out. (clips on back) when you think all the screws are out grab the lower corner of the panel and give it a good yank this should start the panel coming off (behind you will see long plastic '1 inch ' pin type clips you may find six or 8 as you work the panel back/off) if at any point it feels like its not popping free STOP and look for a screw you missed or you will wreck the door panel!!!
power doors will have plugs the go into the switches sum realy **** to remove but careful study should reveal sum kind of release clip or tang you must lift or squeeze . set panel aside when you have it off. but keep the window switch handy you will have to plug it back in usualy twice to align the window holding screws so you can loosen or tighten them when you put the glass back in..that said the panelless door will have a plastic or foam "skin" on it carefuly peel it back ( i use a box cutter blade to cut the sticky stuff if it wont peel back easily, (sum people just cut it and tape it back on after ) this is the dust protector (keeps dust out of cabin of vehicle) once thats removed or folded out of the way plug the window switch in and run either up or down to expose the window hold bolts or clamps.IF REPLACING BROKEN GLASS now is the time to shop vac out all the glass !!!!! it will rattle in the door and drive you crazy if not .ALSO tack a small screwdriver and run it thru the window track that surrounds the door glass IF you leave glass it the track the window will break again and also makes real nasty grindy scratchy sounds. With the glass you buy from an auto wrecker (HELLO BEST PLACES FOR CAR PARTS GOING!!!) clean the glass then look at the opening where the glass goes in if the window "belt" moulding leaves only a small **** to insert the glass pull it up carefuly from one end to remove. dont bend it its not abuse friendly!! tip the glass narrowest end down , most from the outside , and slid it into the door shell,as you get farther in turn and work it into the window track !! dont drop it sometimes the regulator must be lowered down all the way to allow the glass to turn .. watch and set the glass into the holders (some glass has holes some have a track some have plastic tabs ) carefuly tighten either the bolts or clamp what ever style you see in your door!
make it snug but dont try to overtighten or you go back to shop vac !!
test window for up and down NOTE some doors the window trac extends down inside the door and must be loosend off or removed to accomodate the window going in.remember to install these back in if you have to remove them use the marks left by the screws to reset them back to propper fit test BEFORE you put it all back together.
if you are happy with your work .do the belt moulding ,replug things on or atleast pull wire thru the panel ,align the "pins" start at top edge and bang the panel back in (palm of hand punch) NOTE if sum pins stuck in door pry them out and fit them back into panel before putting it back on!! replace screws and you are done as you can tell i've done many door glass replacements most take me an hour to complete including shop vac broken glass off seat and floor n dash GOOD LUCK!!!!!

Posted on Feb 03, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove diver door side mirror


you must first remove the door panel then there will be 3- 10mm nuts holding the mirror on un plug wire harness and replace with new one

May 14, 2014 | 2004 Chrysler Crossfire

1 Answer

Chrysler crossfire a/c problem


Passenger side blows hot air and driver side blows cold.

Jul 08, 2012 | 2005 Chrysler Crossfire

1 Answer

Passenger side headlight assembly removal, is there more than 2 bolts, if so where


You can replace the headlights on your Crossfire easily by yourself. headlight image by Carbonbrain from Fotolia.com

When a headlight burns out on your Chrysler Crossfire, you do not need to rush to the repair shop to have it replaced. You can access the headlights in your Crossfire from within the engine compartment, allowing you to change the headlight yourself. The Crossfire uses an H7U headlight bulb, which you can find at auto parts retail stores or at a Chrysler dealership.
Difficulty: Easy

  1. 1 Open the hood of your Crossfire to gain access to the headlight assemblies. Press down on the tab on top of the light assembly cover. Remove the cover and set it aside.
  2. 2 Pull the electrical connection free of the bulb socket. Press the spring clamps securing the bulb into the light assembly. Pull the bulb straight out of position.
  3. 3 Insert the new bulb in the same position. Ensure that the spring clamps secure the bulb. Press the electrical connection into place.
  4. 4 Replace the light assembly cover and press it into position until it clicks, securing it in place. Repeat the same process on the opposite headlight if required. Close the hood and test the headlight operation.



Dec 12, 2010 | 2004 Chrysler Crossfire

1 Answer

How do you replace passenger side mirror on 2003 Chrysler Town and Country?


If you open the door you will see two screws behind the plastic base remove them and mirror will come off then remove the connector,

Sep 15, 2010 | Chrysler Town and Country Cars & Trucks

1 Answer

Resivior is cracked or broken on a 2005 Chrysler Crossfire... How to get to it to repair or replace it


TAKE OFF PASSENGER WHEEL AND PLASTIC GUARD BEHIND WHEEL. JUST REMOVE ONE BOLT AND PULL OUT RESERVIOR. REPLACEMENT IS $100.

Jun 17, 2010 | 2005 Chrysler Crossfire

1 Answer

Looking to replace passenger side mirror on a 2006 Town and Country. Anyone have Instructions available?


    Remove Old Mirror
  1. 1 Open the side door to the Chrysler Town & Country, and find thescrew that holds the side mirror molding in place.

  2. Take the screw out and remove the molding panel that attached around the outside of the power mirror.

  3. Remove the bolts connecting the mirror to the door assembly. If equipped, unplug the power side view mirror wiring harness connector.

  4. Unplug the electric connectors, and pull the mirror out of the molding.

Jun 01, 2010 | 2006 Chrysler Town & Country

1 Answer

Driver door mirror will not fold in or out on power switch, passenger door mirror comes in and out ok


sounds like your lf mirror motor itself has failed.....check for power at your mirror motor itself...then you can condemn the mirror motor

Nov 09, 2009 | 2000 Chrysler Grand Voyager

1 Answer

How do remove the passenger mirror assembly


With the door open, remove the interior door panel, this will expose the nuts and or screws holding the side view mirror in place. Remove these and reverse the process to install the new mirror.

Sep 08, 2009 | 2005 Chrysler 300

1 Answer

Removing and replacing passenger side mirror 2002 town and country van


there should be a triangle shaped plastic section on the interior of the door behind the mirror, check it for a little plastic screw cover to remove it or you may just have to lever it gently to remove it.
once it is off it exposes the mirror retaining bolts which you undo to remove the mirror, I presume it has electric mirrors and if that is the case you will have to find the electrical wire plug for the mirror and pull it apart, replace mirror in reverse order of removing

May 12, 2009 | 2002 Chrysler Town & Country

2 Answers

Replaceing the passenger side mirror on 2002 Chrysler minivan


Assuming that you have power mirrors, the fix is as follows:
remove the passenger side cover on the windshield/door pillar by first removing the pull handle. My experience has been that with some reasonable pulling the plastic trim should unhook from the body without too much fuss. You may want to buy a trim stick for working around the edges to get the clips loose without marring the plastic. You will also need the trim stick to pull up the plastic cover on the instrument panel (that part that covers the speakers and overlaps the vinyl that faces the passenger compartment) - but pull the panel cover up just enough to get at the mirror electrical connector (if you pull it all the way up no harm will be done) unhooked. Once that is done, move to the outside and remove the plastic cover from the door/mirror assembly (there is a ribbed section that is split into an upper and lower half and you are going to take the trim stick to the top half) The screws holding the mirror in place will no be exposed and you will remove them.

Put things back in reverse order and you're good to go.

Dec 11, 2008 | 2002 Chrysler Voyager

Not finding what you are looking for?
2004 Chrysler Crossfire Logo

Related Topics:

359 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...