Question about 1985 Chevrolet S-10

Open Question

What is the plug gap on a 1985 Chevrolet S10 Pickup

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1596 Answers

SOURCE: I need to replace the fuel pump in my 1985 Chevy S10 Pickup.

EXACT PROCEDURE ! Please Rate Me Fairly for this!! Thank you And Good Luck !!


ELECTRIC PUMP

REMOVAL

  1. Before servicing the fuel pump the fuel system pressure must be relieved. See: Fuel Pressure Release
  2. Disconnect the negative battery cable.
  3. Raise the car on a hoist.
  4. Remove the fuel tank. See Fuel Tank / Service and Repair.
  5. Remove the fuel tank sending unit and pump assembly by turning the cam lock ring counterclockwise. Lift assembly from the fuel tank.
  6. Pull the fuel pump up into the attaching hose while pulling outward away from the bottom support. Take care to prevent damage to the rubber insulator and strainer during removal. After the pump assembly is clear of the bottom support, pull the pump assembly out of the rubber connector for removal. NOTE: Inspect the fuel pump attaching hose for any signs of deterioration. Also check the rubber sound insulator at the bottom of the pump. Replace damaged or deteriorated parts.
INSTALLATION
  1. Push the fuel pump assembly into the attaching hose.
  2. Position the fuel tank sending unit and pump assembly into the fuel tank. Use a new "O" ring seal. NOTE: Care should be taken not to fold over or twist the strainer when installing the sending unit as this will restrict the flow of fuel. Also, verify that the strainer does not block the full travel of the float arm.
  3. Install cam lock over the assembly and lock by turning clockwise.
  4. Reinstall fuel tank.
MECHANICAL PUMP

REMOVAL and INSTALLATION

NOTE: To ease pump installation, rotate the camshaft so the camshaft eccentric is out of the way of the fuel pump rocker arm.

  1. Disconnect fuel lines from fuel pump.
  2. Remove fuel pump mounting bolts and the fuel pump.
  3. Remove all gasket material from the pump and block gasket surfaces. Apply sealer to both sides of new gasket.
  4. Position gasket on pump flange and hold pump in position against its mounting surface. Make sure rocker arm is riding on camshaft eccentric.
  5. Press pump tight against its mounting. Install retaining screws and tighten them alternately.
  6. Connect fuel lines. Then operate engine and check for leaks.

Posted on Mar 22, 2009

Ad
  • 218 Answers

SOURCE: where's the computer located on a 1985 chevy s10

Hi..my name is Keith..and the computer(ECM)..is an aluminum box located in the engine compartment..either mounted to a fender or on the firewall..i hope this helps

Posted on Jun 28, 2009

c17hydro
  • 2984 Answers

SOURCE: How do you replace the water pump?

PLEASE DON'T FORGET TO RATE!!!!

3904240.gif
After removing the cooling fan assembly, remove the water pump pulley-4.3L engine

ae70d4b.gif
Location the water pump pulley bolts-2.2L engine

e1a6562.gif
If the pulley turns when you try to loosen the bolts, attach sockets and ratchets to two of the bolts, insert a pry bar to hold the pulley in place and loosen the bolts-2.2L engine

be1972d.gif
Once all the bolts are unfastened, remove the water pump pulley-2.2L engine

46ec457.gif
Disconnect all hoses attached to the water pump assembly-4.3L engine

18c0897.gif
Unfasten and remove the water pump retaining bolts-4.3L engine

e8016bd.gif
The water pump is retained by four bolts-2.2L engine

30f4c89.gif
Remove the water pump from the vehicle-4.3L engine

9b0c7fe.gif
Removing the water pump from the engine block-2.2L engine

dea099d.gif
Use a scraper to clean the old gasket material from the water pump ...

2eaa00c.gif
... and the water pump-to-engine mating surface

Posted on Nov 11, 2009

ftw1952
  • 10319 Answers

SOURCE: where is the map sensor located on 1985 s10 pickup 2.8 liter v6

it has one vacuum line to it and its half the size of a pack of cigarettes. Look around the intake area

Posted on Jan 10, 2010

Testimonial: "i thank you very much for your answer because i am disabled and need all the help i can get thank you very very much"

  • 1 Answer

SOURCE: My 1999 chevy s10 runs rough at idle

By a ford

Posted on Mar 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vacuum diagram for a 1985 chevy s10 blazer


Deb, all 1985 Chevy Blazers were shipped with a sticker in the engine compartment, which includes a vacuum routing diagram, spark plug gap specification, and firing order. Look around the engine compartment and I'll wager it's still there.

May 10, 2015 | Chevrolet Blazer Cars & Trucks

3 Answers

What number and type of acdelco spark plug fits a 2000 s10 pickup with 4.3 motor ,4x4


2000 Chevrolet Truck S10 P/U 4WD 4.3L SFI 6cylSPARK PLUG ASM
Part Number: 12
Product Notes:
[Rapidfire Spark Plug]; .060 GAP
Per Vehicle: 6; Years: 1996-2001

SPARK PLUG ASM
Part Number: 41-993
Product Notes:
[Platinum Spark Plug]; .060 GAP
Per Vehicle: 6; Years: 1996-2002

From acdelco-catalog


Hope helps (remember to rate this answer).

Jan 04, 2011 | Chevrolet S 10 Cars & Trucks

1 Answer

Where is the map sensor located on 1985 s10 pickup 2.8 liter v6


it has one vacuum line to it and its half the size of a pack of cigarettes. Look around the intake area

Jan 09, 2010 | 1985 Chevrolet S-10

1 Answer

Trying to locate which fuse goes to the license plate lights on a 1985 S10 pickup


Do you have tail lights? If yes ......then the fuse is OK.
The fuse for tail lights is in the fuse box.......either....the one inside or the other in the engine compartment.
Usually it's burnt bulbs and bad connections.

Aug 17, 2009 | 1985 Chevrolet S-10

1 Answer

Where's the computer located on a 1985 chevy s10 pickup


look in the interior passenger side kick panel in front of the door where the panel and carpeting meet

Jun 28, 2009 | 1985 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...