Question about 1994 Chevrolet S-10

1 Answer

Rear wiper assembly 2004 tahoe

My rear wiper blade assembly works sometimes when turned on?

Posted by on

  • Anonymous Mar 17, 2014

    where is the control for the rear wiper in 2003 tahoe

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 122 Answers

Sounds like the ground on the rear wiper motor isn't making a good ground contact , check the wiring see if its connected properly.

Posted on Jan 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replacing 2004 gmc envoy xuv rear wiper blade


Replace the blade and the blade holder. These days everything but the arm gets changed....and gone are the days of just replacing the rubber...

Jul 19, 2011 | 2004 GMC Envoy

1 Answer

2004 Jeep rain sensing wipers continue to run regardless of setting or amount of rain


a couple of thoughts:
Has your windshield just been replaced?
The sensor is up by the rear view mirror, is it plugged in all the way?
Do you have the right size wiper blades on your vehicle? (too short of a blade misses the rain sensor and does not wipe it clean)
How good are your blades? ( as above, to turn off the rain sensor the blade needs to wipe it clean)
The rain sensor works by projecting multiple inferred beams to the inside of the windshield, like a prism, they reflect back to collectors. when there is a water droplet on the outside of the windshield it changes a beams trajectory and it misses the collector thust turning on the wipers.
(yes, this all happens in that little sensor up by the rear view mirror.)
check to make sure the wiper switch is in the right position.
also....I've seen rain sensors not work properly when the hood or doors are open.
hope this helps

Feb 01, 2010 | 2004 Jeep Grand Cherokee

1 Answer

The rear wiper blade no longer works


new rear motor, or linkage inside door broke, or wire broke

Jan 04, 2010 | 2004 Toyota Sienna

1 Answer

2005 tahoe wiper replacement


My tahoe has a plastic piece just to the left of the metal attaching arm. It is easiest to see on the driver side wiper. There is just enough room to slip a flat blade screw driver into and then pop upwards. After this clip is popped, slowly move the wiper blade to the right as you pull that clip further upward. The blade can now be removed. Of course if you have a different type blade this will not work.

Dec 14, 2009 | 2006 Chevrolet Tahoe

1 Answer

Rear windshield wiper does not go back into the stored position. Motor seems to work ok.


I have same problem with a 2004 Tahoe. The wiper hangs up on plastic bracket and won't go back down into off position. Design flaw?

Sep 20, 2009 | 2002 Chevrolet Tahoe

1 Answer

How to replace the wiper insert at the back of


moz-screenshot.jpg
  1. REMOVE RR WIPER BLADE
    1. Raise the rear wiper blade to the position as shown in the illustration where the meshing of the claw disengages with a clicking sound. NOTE: Be careful not to break the claw.
    2. Pull straight the rear wiper blade to vehicle's left from the wiper arm. NOTE: Do not fold the rear wiper arm with the rear wiper blade removed from it.1722d05.gif

  1. REMOVE REAR WIPER RUBBER
    1. Place the rear wiper with the rear end of the rubber protruded from the blade stopper as shown in the illustration. NOTE: Do not pull out the wiper rubber forcibly, as the backing plates will become deformed or the blade claws will become damaged. HINT: The rubber can be easily pulled out by pushing the middle area of the blade.
f54b10a.gif
  1. INSTALL REAR WIPER RUBBER
    1. Install the 2 wiper rubber backing plates to the rear wiper rubber. NOTE: Be careful to observe and keep direction of curvature for correct replacement.
0dd144d.gif
b. Insert the rear wiper rubber from the claw of the middle of the rear wiper blade into the rear end position.
8f40009.gif
c. After passing the rear wiper rubber through the rear end side claw, protrude it from the rear end stopper and pass it through the front tip side claw.

Sep 12, 2009 | 2005 Toyota Matrix

1 Answer

Windshied wipers not working all the time


wiper motor boards go bad in those motor assemblies. You can replace just the board in most applications.

Jul 02, 2009 | 1994 Chevrolet C1500

1 Answer

04 dodge ram 1500 wiper arm goes down before going up


remove wiper arms at the shaft, right at the cowl. each will have a nut on them but it is covered by a piece of plastic that will snap up for access. take nuts off and remove wiper assembly. turn key on turn wipers on make sure shafts turn when on, then turn off the shafts to stop in park position. then reinstall wiper assemblies in their park position .

Dec 28, 2008 | 2004 Dodge Ram 1500

Not finding what you are looking for?
1994 Chevrolet S-10 Logo

270 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...