Question about Mitsubishi Cars & Trucks

Open Question

How do I remove the ignition tumble from mitsubishi triton and replace with another one of the same

Swapping 2001 key tumbler for mitsubishi same 2005 model

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
leetamara
  • 702 Answers

SOURCE: ignition tumbler key

Place key into ignition, use a paper clip and press the tiny hole on the switch. Turn the key back towards ACC position and pull the cylinder right out. Reverse procedure to install.

Posted on Jun 12, 2008

Ad
  • 1 Answer

SOURCE: Ignition Key Doesn't Turn Sometimes in 2001 Jeep Grand Cherokee

test

Posted on Dec 22, 2008

  • 1 Answer

SOURCE: 1996 toyota 4 runner 4x4 6cl key gets stuck in ignition, how do I replace ignition starter switch?

Just a thought , if the gear stick is not in park the key cannot be removed from the ignition I found out when I left the car in nuetral .

Posted on Feb 22, 2009

mechanicm639
  • 253 Answers

SOURCE: lost key to 1998 Chevy S10 Need to remove&replace tumbler w/o key

With the title and an insurance card your dealer can cut a new key by the VIN if you have never replaced the lock cylinder before. If not it will be remove the column covers, drill out the lock and try not to damage the lock housing. Good Luck

Posted on Jun 22, 2009

  • 104 Answers

SOURCE: removal and replacement of key tumbler 1994 Ford explorer

look at the steering column below the ign lock and tumbler there should be a small hole turn key to on pos and push a small rod up the holethis then should release the lock and tumbler,no hole then wheel and coumn has to be stripped to get to lock retainer

Posted on Oct 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace my ignition lock cylinder in my 2000 Mitsubishi mirage without the key?


best advice is to get a locksmith to do the job. They will be able to put in a new tumbler, supply the correct fob keys for the immobiliser and possible program it to the vehicle . IF not you will have to take the keys and the vehicle to a service dealer to have it programmed.

Dec 27, 2014 | 2000 Mitsubishi Mirage

1 Answer

How to replacing keyed ignition switch in 2011 sorento


Either the tumblers or the key it's self is worn out.

To replace the Tumbles, you will have to remove everything surrounding it n order to get to it. Normally it is pretty easy after that (if you can turn the key) You turn the key on, and there is a hidden little button indented into the frame work around the key, insert something small to press it in, then pull out on the key and tumbler and the whole thing should slide out.

May 15, 2014 | 2011 Kia Sorento

1 Answer

99 Mitsubishi mirage, the wife lost second key, can i still replace ignition tumbler


If you replace the ignition switch tumbler then you also will have to get a new key and that will cost you 2 keys and reprogramming. Cheaper just to get 1 new key and program it from yours or the car.

Aug 19, 2013 | Cars & Trucks

1 Answer

My 2001 PT Cruiser ignition switch will not turn. I have tried moving the steering wheel up and down, moving the steering wheel left to right while trying to turn the ignition on all to no avail. Help.


was the ignition switch getting hard to turn with the key for a while or did this just all of a sudden happen usually the problem has been going of for a while but people just ignore it until it gets to this point,it sounds like the tumblers in the ignition key switch have gone bad and the tumbler assembly needs to be replaced,the new tumbler assembly can keyed to the original key if the key is not worn out.this should be replaced with a new key if it is.

Mar 08, 2011 | 2001 Chrysler PT Cruiser

3 Answers

2001 gmc yukon xl key in ignition won't turn to start at all.


The tumblers in the ignition lock may be seized, try cleaning it out first with a small spray of WD40 and try the spare ignition keys. The keys it self may be too worn down for the tumblers in the lock and if you have lots of other keys on your key chains, this will promote the lock to wear out quicker. Good luck and hope this helps and try turning the steering where back and forth as you try to turn the ignition key.

Dec 13, 2009 | 2001 GMC Yukon XL

1 Answer

Oldsmobile 2001 intrigue Ignition main the key will not turn


Possible fix for the year of car is a worn key or tumbler or both. Check with Olds with your car vin number to cut a new key. If it's the tumbler, it will have to be re-pinned with new pins by locksmith or replaced with new tumbler. Rare occasions the turning of steering wheel frees the steering locks pressure hold on ignition tumbler. New tumbler can be reset to match door so as not to have two different keys.

Nov 12, 2009 | 2001 Oldsmobile Intrigue

1 Answer

Power is on all the time with or without the key in the ignition. There are no positions (ie...accessories, on, start). When the key is inserted it moves freely in all positions. I removed the steering...


ok some where on the tumbler there will be a very small pin hole you will have to put the key in turn it forward one click then take something that will fit in the pin hole and push in and pull out on the key this should remove the tumbler then follow the directions on the new tumbler to put it in

Jun 06, 2009 | 2001 Ford Ranger Regular Cab

1 Answer

Sticking ignition switch on 2004 Suburban??


you need to replace the tumbler but first you can try a new key if you do not think its the tumbler set key could just be worn but more and likely not .the tumble is shot not too bad to change .

Mar 03, 2009 | 1996 Chevrolet Suburban

2 Answers

2001 Mazda Millenia ignition switch / steering wheel locked


The tumblers have wore down and won't let the key turn. At this point you need to have the tumbler set replaced.
God Bless You Greg

Jan 04, 2009 | 2001 Mazda Millenia

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...