Question about Cars & Trucks

1 Answer

Where is a fule pump reset switch located on a 1988 toyota corolla?

Posted by on

Ad

1 Answer

Only on a ford product

Posted on Dec 02, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel pump relay switch location 2006 toyota corolla


There isn't one. Almost no vehicle has one. They were common only in ford vehicles in the late 80's and early 90s.

Aug 17, 2016 | 2006 Toyota Corolla

1 Answer

Where is the fuel pump on a 1988 toyota corrolla station wagon


I don't know if your fuel injected or carb? If your fuel injected, probably electric fuel pump, in the gas tank. If not fuel injected, probably a mechanical fuel pump, under the hood, note picture.

fuel-pump-1988-toyota-corrolla-station-px1oa4s1mnc4r5fmbg0hxgth-5-0.jpg

Mar 06, 2016 | 1988 Toyota Corolla 4 Door

3 Answers

Location of fuel pump relay 1994 toyota corolla


The fuel pump relay is located in the fuse box drivers side of fuse box

Jan 26, 2012 | 1994 Toyota Corolla

1 Answer

Hi, i have a 1988 toyota conquest. the oil light continously stays on. But when i rerve it up the light goes on. Oil is full. Im thinking its the oil pump? i dont think its the oil light sensor but im not...


If oil level is OK, then it is possible that the warning light pressure switch which is screwed into the engine oil pressure system is faulty and setting off light and needs replacing. There could even be oil leaking out of the switch. The switch is usually located near the oil filter and will have a wire connected to it.
If after replacing switch and light still comes on, check to make sure wire is not making contact with the engine because of cracked insulation or it could also mean badly worn engine bearings. It is unlikely to be the oil pump as these hardly ever fail.

Sep 17, 2010 | 1988 Toyota Corolla 4 Door

2 Answers

How do i check fuel pump on 1993 toyota corolla


THis is normally done with a pressure gauge on the fuel rail. Do you suspect a fuel delivery problem? Take off the air filter and spray a little carb cleaner in the intake manifold and crank. If it tries to start you are going in the right direction possibly fuel pump. Use extreme caution not to spreay too much. If the car backfires you may see a backflash flame!

Jul 29, 2010 | 1993 Toyota Corolla

1 Answer

Where is fuel reset button on 1993 toyota corolla wagon


i am pretty sure that this type of car does not have a reset button for the fuel.i have the same toyota,but mines is a sedan and i have never seen one on it.if your not getting any fuel,check your fuses,if good,check your fuel pump which is located right under your rear seat.hope this info helps.good luck and take care, manny

Jun 16, 2010 | 1993 Toyota Corolla

1 Answer

Fule cut off switch were is it located


There is a fuel pump relay located behind the clove compartment on the passenger side. Remove the philips screws and pull out the glove box. There you will see the relay that turns off the fuel pump.

Oct 04, 2009 | 1995 Toyota Camry

1 Answer

Trying to locate relay for fuel pump


fuel pump is inside gas tank, relay is under hood on same side as battery

Oct 02, 2009 | 1988 Toyota Camry

2 Answers

Need to know where to find fuse for fule pump 94 arostar


no fuse for the fuel pump, it is regulated by computer box.

Apr 14, 2009 | 1988 Ford Aerostar

1 Answer

1988 toyota corolla sr-5


Locate the brake switch up above the brake pedal. Push in on plunger and check if brake lights go out. This switch can be unplugged and removed from its spot at the pedal. Then you can pull out plunger and reset it, put back in its spot, and let pedal readjust to the appropriate travel. It should automatically set to correct stroke length after pulling plunger outward to its furthest length. If this switch, or its adjustment is not to blame, post again. I will help more if needed.

Thanks, I hope this helps. TT

Jan 29, 2009 | 1988 Toyota Corolla 4 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...