Question about 1999 Chrysler 300M

1 Answer

1999 300M timing is off how can i fix it

I just had to replace my water pump and timing belt in my 99 300M and read to align the marks for the TDC and make sure the sprockets were in the right place but i didn't read that I was not supposed turn them without the timing belt on. i turned the sprockets and they jerked about 1/4 turn each it didn't feel right and i tried to turn them back to where the were supposed to be but now the car wont start. Can someone please help me with what to do to get it timed right PLEASE!

Posted by on

  • Anonymous Dec 02, 2012

    Go to a repair shop & they should print a hard copy of the diagram for the timing of cams etc from their data base Ask if they have ALLDATA ,Mitchell or Identifix System at the shop

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 378 Answers

This is gunna be hard you always always always have to mark the sprockets good luck

Posted on Dec 02, 2012

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

BLAZZ81
  • 281 Answers

SOURCE: 99, chrysler ,300m..1 month ago changed timing

check the timing belt!! may have been put on to loose or to tight,

Posted on Mar 12, 2010

  • 198 Answers

SOURCE: i replaced the water pump

remove and retime your distributor, sounds like it's 180 degrees out of time.

Posted on Oct 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced water pump lined belt marks now the marks are off after turning motor over by hand


How to get my timing back correct after replacing timing belt.

www.cargurus.com > Questions > Dodge > Journey
CarGurusJan 18, 2015 - I have went in and replaced the water pump and the timing belt. ...Align the crankshaft sprocket (10) with the TDC mark (9) on the oil pump cover. 2. ...and then just shut off and won't restart? try unplugging the cam ... The two timingmarks for the camshafts are lined up and the crank is lined up with TDC.

Timing Belt Change - Miata.net


Nov 23, 2015 | Cars & Trucks

Tip

How to change a timing belt on a hyundai Elantra 1.5 , 1.6 and 2.0 engine


1.5L And 1.6L Engines
  1. Remove all necessary components for access to the timing belt cover, then remove the cover.
  2. Rotate the crankshaft clockwise and align the timing marks so No.1 piston will be at Top Dead Center (TDC) of the compression stroke.
  3. Loosen the tensioning bolt and the pivot bolt on the timing belttensioner. Move the tensioner as far as it will go toward the waterpump. Tighten the adjusting bolt.
  4. Mark the timing belt with an arrow showing direction of rotation if belt is to be reused.
  5. Remove the timing belt.
  6. If defective, remove the timing belt tensioner.

To install:


0900c1528019701f.jpgenlarge_icon.gifenlarge_tooltip.gifFig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines


0900c15280197020.jpgenlarge_icon.gifenlarge_tooltip.gifFig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines
  1. Align the timing marks of the camshaft sprocket and check that the crankshaft timing marks are still in alignment.
  2. If removed, install the timing belt tensioner, spring and spacer with the bottom end of the spring free. Tighten the adjusting bolts lightly with the tensioner moved as far as possible away from the water pump.
  3. Install the free end of the spring into the locating tang on the front case.
  4. Position the timing belt over the crankshaft sprocket, then over the camshaft sprocket. Slip the back of the belt over the tensioner wheel.
  5. Turn the camshaft sprocket in the opposite of its normal direction of rotation until the straight side of the belt is tight and be sure the timing marks align.
    NOTE If the timing marks are not properly aligned, shift the belt 1tooth at a time in the appropriate direction until they are aligned.
  6. Loosen the tensioner mounting bolts so the tensioner works,without the interference of any friction, under spring pressure. Be sure the belt follows the curve of the camshaft pulley so the teeth are engaged all the way around. Correct the path of the belt, if necessary.
  7. Tighten the tensioner adjusting bolt, then the tensioner pivot bolt to 15-18 ft. lbs. (20-26 Nm).
    NOTE Bolts must be tightened in the stated order or tension won't be correct.
  8. Turn the crankshaft 1 turn clockwise until timing marks again align to seat the belt.
  9. Loosen both tensioner attaching bolts and let the tensioner position itself under spring tension. Retighten the bolts.
  10. Check belt tension by putting a finger on the water pump side ofthe tensioner wheel and pull the belt toward the water pump. The belt should move toward the pump until the teeth are approximately 1 / 2 of the way across the head of the tensioner adjusting bolt. Re-tension the belt, if necessary.
  11. Install the timing belt covers and all other related components.
moz-screenshot.jpg6a4c46b.jpg8c77128.jpg74ba305.jpg

on Dec 01, 2009 | Hyundai Elantra Cars & Trucks

1 Answer

Replace water pump 2004 clk500


Hi Scott, Work evolved in replacing a water pump depends on the vehicle. Some vehicles have the pump driven by the timing belt, while others drive via a 'V' belt or PK (Serpentine belt) If your is the latter, take a few photographs of the lacing for the reassembly before doing any disassembly. If it is a vehicle using the timing belt, photograph the serpentine belt and then remove it and the timing cover. Before removing the timing belt, rotate the engine to TDC and align the timing marks before taking off the belt. It is always a good idea to paint a spot of white paint onto the gears and the engine. Once the match marks have been identified and aligned, loosen the tensioner bearing fully before removing the belt. When refitting, set the marks by adjusting the belt alignment on the opposite side to the side fitted with the tensioner. Once aligned, retention and check the alignment again. If you're happy turn the engine by hand at least four times and recheck the matching up of the marks each second turn. Changing the water pump is straight forward and child's play compared to the associated work. Regards John

May 25, 2014 | Cars & Trucks

2 Answers

Timing belt


TIMING BELT & SPROCKETS R & I
NOTE: Some procedures may differ slightly due to engine
construction.
Removal
1) Remove all necessary air ducts. Position No. 4 piston at
TDC of compression stroke. Align timing marks. See Fig. 2. Remove fan
and fan shroud. Remove belts. If necessary, remove radiator and
splashguard.
2) Prevent engine from rotating and remove crankshaft timing
pulley retaining bolt. Remove upper and lower timing belt covers.
Remove spring from tension pulley. Loosen adjusting bolt and move
pulley toward water pump. Remove timing belt.
CAUTION: Ensure pistons are at TDC when rotating camshaft or damage
may result.
Inspection
1) Handle timing belt carefully. Avoid twisting or kinking
belt. Do not allow belt to become contaminated by water, oil, dirt or
other contaminates. Inspect belt for cracks or damage. If necessary,
replace.
2) Measure tension pulley spring length and force. Spring
length should not exceed 2.76" (70.2 mm) and spring force should not
be less than 197-347 lbs. (27-48 kg).
3) Replace tension pulley spring if not within specification.
Installation
1) Pull tensioner fully toward water pump side and
temporarily tighten retaining bolt. Ensure No. 4 cylinder is at TDC on
compression stroke by rotating crankshaft until keyway aligns with
mark on front crankshaft seal housing (12 o'clock). Rotate camshaft
until timing mark on cam gear (arrow) aligns with mark on upper
camshaft cover (notch). See Fig. 2.
NOTE: When timing marks are aligned as stated above, No. 4 piston
is at TDC on compression stroke.
2) Position timing belt over crankshaft sprocket, oil pump
sprocket, camshaft sprocket and tensioner in that order. Ensure belt
is positioned in sequence given and without slack between sprockets.
Loosen tension sprocket adjusting bolt allowing spring tension to
tighten belt. Tighten adjusting bolt temporarily.
3) Temporarily install crankshaft pulley bolt and rotate
crankshaft 2 complete revolutions in opposite direction of engine
rotation, until marks on crankshaft and front oil seal retainer are
aligned again. See Fig. 2. Loosen tensioner lock bolt, allowing
tesioner spring to fully adjust tension. Tighten tensioner lock bolt.
4) Install timing belt covers. To complete installation,
reverse removal procedures. Tighten all bolts to specification. See
TORQUE SPECIFICATIONS table at end of this article.
Fig. 2: 2.3L & 2.6L Timing Alignment Marks
Courtesy of Isuzu Motor Co

Dec 13, 2010 | 1989 Isuzu Pickup 2WD

1 Answer

Timing belt broke,engine out of time,need to timing and install new belt how do i set timing.98 escort zx2 2.0 L


2.0L Engine SOHC ENGINE
  1. Remove the drive belt and timing cover.
  2. Raise the car and support it with safety stands.
  3. Remove the right-hand splash shield and the crankshaft pulley. Fig. 11: The timing marks on both the camshaft and crankshaft pulleys must be aligned like this before removing or installing the timing belt — 2.0L SOHC engines 90983g66.gif

  4. Align the timing marks as illustrated in the accompanying illustration.
  5. Refer to the accompanying illustration and remove the timing belt as follows:
    1. Loosen the timing belt tensioner bolt (1).
    2. Use an 8mm Allen wrench, and turn the tensioner (2) counterclockwise 1⁄4 turn.
    3. Insert a 1⁄8 inch drill bit in the hole (3) to lock the belt tensioner in place.
    4. Remove the timing belt (4). Fig. 12: Remove the timing belt by following these 4 numbered steps (refer to the text for an explanation) — 2.0L SOHC engine 90983g67.gif

    5. Inspect the belt for damage and signs of oil leakage. To install: NOTE: Install the timing belt over the sprocket in a counterclockwise direction starting at the crankshaft. Keep the belt span between the crankshaft and camshaft tight when installing the belt over the camshaft.
  6. Install the timing belt and remove the drill bit.
  7. Tighten the tensioner bolt to 15–22 ft. lbs. (20–30 Nm).
  8. Rotate the engine two complete revolutions and make sure the timing marks are aligned.
  9. Install the timing belt cover and crankshaft pulley.
  10. Install the right-hand splash shield and the drive belt.
  11. Start the car and check for proper operation.
DOHC ENGINE NOTE: A camshaft alignment timing tool (No. T94P-6256-CH or equivalent) and a crankshaft Top Dead Center (TDC) timing peg tool (No. T97P-6000-A or equivalent) are required for this procedure. NOTE: Make sure the correct notch in the pulley is indexed to the lower cylinder block. Refer to the accompanying illustration. Fig. 13: A camshaft alignment timing tool . . . 90983g68.gif
Fig. 14: . . . and a crankshaft TDC timing peg tool are required when removing and installing the timing belt 90983g69.gif
  1. Remove the spark plugs.
  2. Rotate the crankshaft to TDC.
  3. Locate and remove the plug bolt by the Crankshaft Position (CKP) sensor (refer to the illustration) and install the TDC timing peg. Fig. 15: Remove the plug bolt by the Crankshaft Position (CKP) sensor and install the TDC timing peg 90983g70.gif

  4. Raise the car and support it with safety stands.
  5. Unfasten the splash shields bolts and remove the shield.
  6. Lower the car and remove the water pump pulley.
  7. Remove the valve cover and the timing belt covers.
  8. Align the camshafts and install the camshaft alignment tool on the back of the camshafts as illustrated. Fig. 16: Align the camshafts and install the alignment tool 90983g76.gif
    WARNING
    If the camshaft belt is being reused, mark the direction of the camshaft belt to the rotation of the camshaft prior to removal, or premature wear and belt failure could occur.
  9. Loosen the tensioner pulley bolt and relieve the tension on the belt by disconnecting the tensioner tab from the timing cover back plate.
  10. Slide the belt off the sprockets.
  11. Inspect the belt for wear and replace as necessary. Fig. 17: Timing belt routing — 2.0L DOHC engine 90983g71.gif
    To install:
  12. If, for any reason, the engine was disturbed, the camshafts moved or the sprockets replaced, perform the following procedure: NOTE: Make sure the correct notch in the pulley is indexed to the lower cylinder block.
    1. Position the crankshaft just prior to Top Dead Center (TDC).
    2. If not already done, locate and remove the plug bolt by the Crankshaft Position (CKP) sensor (refer to the illustration) and install the TDC timing peg.
    3. Rotate the crankshaft clockwise against the TDC peg. NOTE: Installation of the alignment tool into the exhaust camshaft may require the camshafts to be rotated clockwise.
    4. Install the camshaft alignment tool on the back of the camshafts.
    5. Install the timing belt and engage the timing belt tensioner tab into the upper timing cover backplate. NOTE: A 3⁄8 inch drive, 10mm, 2 inch torque adapter offset is required to tighten the tensioner bolt.
    6. Using a 6mm Allen wrench, adjust the tensioner until the index marks are aligned and tighten the bolt to 17–20 ft. lbs. (22–28 Nm).
    7. Rotate the crankshaft clockwise against the TDC alignment peg, then remove the camshaft alignment tool.
    8. Remove the TDC peg tool and install the plug bolt.
    9. Install the timing and valve covers.
    10. Install the water pump pulley and the splash shield.
    11. Install the spark plugs. If the engine or the camshaft were not disturbed in any way, or the sprockets were not removed, perform the following procedure:
  13. Install the timing belt and engage the timing belt tensioner tab into the upper timing cover backplate. Fig. 18: Engage the timing belt tensioner tab into the upper timing cover backplate . . . 90983g72.gif
    Fig. 19: . . . then use a 6mm Allen wrench to adjust the tensioner until the index marks are aligned 90983g73.gif
    Fig. 20: A 3⁄8 inch drive, 10mm, 2 inch torque adapter offset is required to tighten the tensioner bolt (arrow) — 2.0L DOHC engine 90983g75.gif
    NOTE: A 3⁄8 inch drive, 10mm, 2 inch torque adapter offset is required to tighten the tensioner bolt.
  14. Using a 6mm Allen wrench, adjust the tensioner until the index marks are aligned and tighten the bolt to 17–20 ft. lbs. (22–28 Nm).
  15. Rotate the crankshaft clockwise against the TDC alignment peg, then remove the camshaft alignment tool. Fig. 21: Rotate the crankshaft clockwise against the TDC alignment peg 90983g74.gif

  16. Remove the TDC peg tool and install the plug bolt.
  17. Install the timing and valve covers.
  18. Install the water pump pulley and the splash shield.
  19. Install the spark plugs.
prev.gif next.gif

Aug 26, 2010 | Ford E-Series Cars & Trucks

1 Answer

I've got a '99 Breeze that the timing belt was replaced when a water pump was done. Unfortunately, when the person did the job they didn't align the timing marks before disassembling. They reassembled...


YOu always need a TDC.
It is very simple if you do it correctly as following:
1 - Timing the ignition at cylinder #1
2- Make sure the piston # 1 is up for compression stage, not exhaust stage. It means if the cylinder #1 is up, then the intake and exhaust vales are not opened.
3- The crankshaft mark and the camshaft mark has to be aligned at the straight point, this is why we call TDC.
4- To have an easy time to turn the camshaft for aligning, it is best to take off all the spark plugs so you don't have to work against the compression built up whenever the pistons move up.
good luck

Aug 15, 2010 | 1999 Plymouth Breeze

1 Answer

Hiwich timing mark I used to time the balancer shaft on a 99 honda accord with a 2.3L


To Install:
NOTE: Clean balancer belt drive pulley, timing belt pulleys and upper/lower timing cover prior to belt installation.
honda-03-23-3425.gif

  1. Set timing belt drive pulley to TDC by aligning dimple on pulley with dimple on oil pump. honda-03-23-3426.gif

  2. Set camshaft pulley to TDC so that "UP" mark is at top and grooves align with top of cylinder head. Timing belt installation honda-03-23-3549.gif

  3. Starting with driver pulley, install timing belt in a counterclockwise sequence.
  4. Loosen and ten retighten adjusting nut.
  5. Install balancer belt drive pulley. NOTE: Inspect rubber seal on lower cover and replace as necessary.
  6. Install lower cover.
  7. Install crankshaft pulley and bolt.
  8. Rotate crankshaft pulley counterclockwise several times to seat belt.
  9. Loosen adjusting nut 1 turn.
  10. Rotate crankshaft counterclockwise 3 teeth on camshaft pulley.
  11. Tighten adjusting nut to 33 ft lb (44 Nm). honda-03-23-3542.gif

  12. Turn crankshaft pulley until TDC is achieved. honda-03-23-3426.gif

  13. Ensure that camshaft pulley "UP" mark is at top and grooves align with top of cylinder head.
  14. Remove crankshaft pulley and lower cover.
  15. Rotate crankshaft to TDC again and lock timing belt adjuster arm with a 6 mm timing cover bolt.
  16. Loosen adjuster nut 1 turn and ensure that belt tensioner freely moves.
  17. Push tensioner up and tighten adjusting nut. Balancer shaft alignment honda-03-23-3556.gif

  18. Remove bolt and washer from maintenance hole.
  19. Using a 6 X 100 mm bolt, scribe a mark 2.9 in (74 mm) from end.
  20. Insert bolt into maintenance hole and hole in balancer shaft.
  21. Install bolt up to scribed line. Balancer shaft alignment honda-03-23-3557.gif

  22. Align groove on balancer shaft with pointer on oil pump housing.
  23. Install balancer belt and loosen adjusting nut 1 turn to tension.
  24. Retighten bolt. Balancer shaft alignment honda-03-23-3556.gif

  25. Remove bolt from maintenance hole and install bolt and washer. Tighten to 22 ft lb (29 Nm).
  26. Reinstall crankshaft pulley.
  27. Loosen adjusting nut 1 turn.
  28. Rotate crankshaft pulley counterclockwise 1 turn and tighten adjusting nut.
  29. Remove bolt from timing belt adjuster arm. NOTE: Inspect rubber seal on lower cover and replace as necessary.
  30. Remove crankshaft pulley.
  31. Install lower cover.
  32. Install seal at adjusting nut. NOTE: Crankshaft pulley, bolt and washer must be cleaned prior to installation.
  33. Lubricate crankshaft pulley bolt between head and washer and bolt threads with clean engine oil. honda-03-23-3537.gif

    CAUTION
    Do not use impact wrench to perform following step.
  34. Install crankshaft pulley and tighten bolt using special tools to 181 ft lb (245 Nm).
  35. Install dipstick/tube assembly.
  36. Install upper cover. Tighten bolts to 9 ft lb (12 Nm).
  37. Install cylinder head cover.
  38. Install alternator bracket and alternator.
  39. Install power steering pump belt and alternator belt. Upper bracket installation honda-03-23-3420.gif

  40. Install upper bracket and tighten fasteners in proper numbered sequence.
  41. Install stop.
  42. Install battery and enter radio anti-theft code.
prev.gif next.gif

Jul 03, 2010 | Cars & Trucks

1 Answer

How to change a timing belt in a 2001 pt cruiser 2.4 liter


REMOVAL
  1. Disconnect negative battery cable.
  2. Raise vehicle on hoist. Remove right front wheel.
  3. Remove the right splash shield.
  4. Remove accessory drive belts.
  5. Remove crankshaft damper
  6. Remove the lower torque strut
  7. Disconnect exhaust system from manifold.
  8. Disconnect A/C pressure switch at rear of compressor housing.
  9. Lower vehicle and support engine with a jack.
  10. Discharge A/C system and disconnect A/C lines at coupling block
  11. Remove upper torque strut
  12. Remove screw attaching ground strap to strut bracket.
  13. Remove torque strut bracket from strut tower.
  14. Remove upper radiator support crossmember
  15. Remove power steering pump and bracket. Set pump aside. Do not disconnect lines from pump.</B>
  16. With engine properly supported, remove right engine mount through bolt.
  17. Raise engine with jack until engine support bracket bolts are accessible.
  18. Remove support bracket bolts.
  19. Remove support bracket.
  20. Remove upper timing belt cover fasteners and remove cover.
  21. Remove lower timing belt cover fasteners and remove cover
  22. CAUTION: When aligning crankshaft and camshaft timing marks always rotate engine from crankshaft. Camshaft should not be rotated after timing belt is removed. Damage to valve components may occur. Always align timing marks before removing timing belt.
  23. Before the removal of the timing belt, rotate crankshaft until the TDC mark on oil pump housing aligns with the TDC mark on crankshaft sprocket (trailing edge of sprocket tooth)
  24. NOTE: The crankshaft sprocket TDC mark is located on the trailing edge of the sprocket tooth. Failure to align trailing edge of sprocket tooth to TDC mark on oil pump housing will cause the camshaft timing marks to be misaligned.
  25. Install 6 mm Allen wrench into belt tensioner. Before rotating the tensioner, insert the long end of a 1/8” or 3 mm Allen wrench into the pin hole on the front of the tensioner .
  26. While rotating the tensioner counterclockwise, push in lightly on the 1/8” or 3 mm Allen wrench, until it slides into the locking hole.
  27. Remove timing belt. CAUTION: If timing belt was damaged due to incorrect tracking (alignment), the belt tensioner assembly must be replaced

INSTALLATION
  1. Set crankshaft sprocket to TDC by aligning the sprocket with the arrow on the oil pump housing.
  2. Set camshafts timing marks so that the exhaust camshaft sprocket is a 1/2 notch below the intake camshaft sprocket
  3. CAUTION: Ensure that the arrows on both camshaft sprockets are facing up.
  4. Install timing belt. Starting at the crankshaft, go around the water pump sprocket, idler pulley, camshaft sprockets and then around the tensioner
  5. Move the exhaust camshaft sprocket counterclockwise to align marks and take up belt slack. NOTE: A new tensioner is held in the wound position by a pull pin.
  6. Remove the pull pin or Allen wrench from the belt tensioner.
  7. Once the timing belt has been installed and tensioner released, rotate the crankshaft two (2) complete revolutions. Verify that the TDC marks on crankshaft and timing marks on the camshafts are aligned as shown in .
  8. Install lower timing belt cover and tighten fasteners to 9 N·m (80 in. lbs.
  9. Install upper timing belt cover and tighten fasteners to 9 N·m (80 in. lbs.
  10. Install right engine support bracket. Ensure the power steering pump is properly located in mounting location on bracket. Tighten mount bracket bolts to 61 N·m (45 ft. lbs.)
  11. Lower engine into mounting position and install right engine mount through bolt. Tighten bolt to 118 N·m (87 ft. lbs.).
  12. Install power steering pump and bracket.
  13. Install upper radiator support crossmember
  14. Install torque strut bracket to strut tower.
  15. Connect ground strap to bracket.
  16. Install upper torque strut
  17. Connect A/C lines. Evacuate and recharge A/C system
  18. Raise vehicle.
  19. Connect exhaust system to manifold.
  20. Connect A/C pressure switch connector.
  21. Install crankshaft damper
  22. Install accessory drive belts
  23. Install lower torque strut
  24. Perform torque strut adjustment procedure
  25. Install right splash shield.
  26. Install right front wheel.
  27. Connect negative cable to battery.

May 15, 2010 | 2001 Chrysler PT Cruiser

2 Answers

Need the timing marks for 2001 hyundai tiburon


1.5L And 1.6L Engines

a826891.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines


4e7384e.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines



1.5L Engines

238c1f1.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines


b1c71ee.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines


c200f83.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines, 1.6L similar



1.8L (VIN M) And 2.0L (VIN F) Engines

656db91.jpg

Fig. Proper alignment of the timing belt alignment marks for belt removal and installation-Hyundai 1.8L and 2.0L (VIN F) engines



2.0L (VIN P) Engines

7208166.jpg

Fig. Oil pump and crankshaft inner timing belt sprocket alignment marks-Hyundai 2.0L (VIN P) engines


7080ea8.jpg

Fig. Timing belt sprocket alignment mark locations and positioning for belt removal and installation-Hyundai 2.0L (VIN P) engines



3.0L (VIN G)

3b377fb.jpg

Fig. Installation of the timing belt-3.0L (VIN G) engine




7b32092.jpg


Fig. Timing belt sprocket alignment mark positioning for belt removal and installation-Hyundai 3.0L engine


Hope this helped (remember comment and rated this post).

Apr 13, 2010 | 2001 Hyundai Tiburon

1 Answer

Needing schematics for timing belt on a 2000 se


Removal & Installation

2.0L Engine
  1. Remove or disconnect the following:

    Negative battery cable Spark plugs Catalytic converter Right front wheel Right inner splash shield Accessory drive belt and idler pulley
  2. Rotate the crankshaft to Top Dead Center (TDC) and install Crankshaft TDC Timing Peg T97P-6000-A.
  3. Rotate the crankshaft clockwise against the peg.
  4. Remove or disconnect the following:

    Water pump pulley Valve cover Crankshaft pulley Timing belt covers
  5. Install Camshaft Alignment Timing Tool T94P-6256-CH into theslots of both camshafts at the rear of the cylinder head to lock thecamshafts into position.
  6. Loosen the timing belt tensioner bolt and relieve the tension onthe timing belt by disconnecting the tensioner tab from the timingcover back plate.
  7. Remove the timing belt.

    0900c152801e2a75.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Crankshaft alignment position-Ford 2.0L (VIN 3) engines


    0900c152801e2a76.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Placement of Camshaft Alignment Timing Tool T94P-6256-CH-Ford 2.0L (VIN 3) engines


    0900c152801e2a77.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Timing belt tensioner index marks-Ford 2.0L (VIN 3) engines

To install:

NOTE Always replace the timing belt after loosening or removing it.
  1. Install the timing belt.
  2. Engage the timing belt tensioner tab into the timing cover back plate.
  3. Adjust the timing belt tensioner until the index marks are aligned. Tighten the tensioner bolt to 17-20 ft. lbs. (22-28 Nm).
  4. Remove the camshaft alignment tool and the crankshaft TDC peg.
  5. Install or connect the following:

    Timing belt covers Crankshaft pulley. Tighten the bolt to 81-89 ft. lbs. (110-120 Nm). Valve cover Water pump pulley Accessory drive belt and idler pulley Right inner splash shield Right front wheel Catalytic converter Spark plugs Negative battery cable
  6. Start the engine and check for proper operation.

Apr 08, 2009 | 2000 Ford Contour

Not finding what you are looking for?
1999 Chrysler 300M Logo

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...