Question about 2000 Chevrolet Venture

1 Answer

How do you know if the master cylider is bad - 2000 Chevrolet Venture

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 129 Answers

Breaks wont pump up or stop the car. If the break is hard to push then it is the vacume booster.

Posted on Dec 02, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I NED TO KNOW WHY MY MASTER CYLIDER ISLL NOT PUMPING BRAKES UP


air in the master cylinder
prime the pump first by undoing the line at the pump and use your finger as a valve over the hole

Aug 05, 2017 | Cars & Trucks

1 Answer

Driving changed rotors bearings calipers lines master cyinder an still does same thing


I would presume this is a potential issue with the master cylinder not allowing fluid to return to the reservoir.
If the ABS had an issue, then the issue would likely be between the ABS unit and the brake unit.

Nov 05, 2012 | 1999 GMC Suburban

1 Answer

92 chevy z71 4wd pickup clutch slipping


Being a single piston master i do not see how it could be holding pressure on the the slave cylinder. if your clutch petal is releasing high you need a new clutch and pressure plate

May 29, 2017 | 1992 Chevrolet K1500

1 Answer

I have a 92 ford f150 2wheel drive my emergancy brake light an abs light comes on after driving for a bit an when i come to a stop then try to drive it feels like my brakes are ingaged an the wheels r...


That year was bad about the float in the master cylider getting stuck..Look in the master cylinder and see if it moves up and down...Also check the wires at the master cylinder make sure a good connection..If its the rear wheels draggin..You might have a stuck wheel cylinder ,,and when the beake cylinder doesnt retract ,,the abs senses that and throws a light..That is if you have drums on the back..

Sep 20, 2011 | 1997 Ford F150 Regular Cab

1 Answer

I replaced clutch master cylider and sleigh cyclinder and still dont have any clutch pressure padel wont stand up and cant get any gears


?. Did you bench bleed all of the air out of the 2 master cylinders before installing on your vehicle, it sounds like that it has air in the sysytem, try bleeding the cltch master cylinder and the bleed off the slave cylinder, that should put you on par.

Oct 20, 2010 | 1990 Nissan 300ZX

1 Answer

I put 2 front brakes shoes on my 1995 Nissan Maxima,what is the correct way to bleed my brakes?Is their any order that i need to follow?


Did you open the bleeder screws at all. If not you may not need to bleed the brakes just pump the pedal to bring the caliper pistons out and your pedal should feel fine. If you just want to blled anyways open all your bleeder srews and as the fluid level in your brake master cylider goes down refill with new dot 3 brake fluid (do not alow the master cylider to drain completely). Close bleeders when you get clean fluid through. Start at passenger rear corner and have a buddy press the brake pedal down. open bleeder, close bleeder after squirt of fluid then have buddy release pedal. Do this a couple of time per corner. Go from pass rear to drivers rear then pass. front ending with driver front. You just flushed your brake fluid. Hope this helps.

Oct 05, 2010 | 1995 Nissan Maxima

1 Answer

Pedal wont depress brake fluid on master cylinder fluid level good no recent brake work


Does it go all the way to the floor? or does it stay at the top? if it stays at the top and they do not work then the master cylider is bad or the booster brake is defective. you will have to test this but you will need speceal tools. Do you have line wrenchs? if you do respond to this and I will tell you how to test the system.

Apr 19, 2010 | 1992 Dodge Caravan

2 Answers

I have a 1991 GMC Sonoma 2Wd with a 4.3 V6. I'm having trouble with the rear brakes still spinning. I just replaced all the brake parts in the back, wheel cylinders, drums, springs, etc. I replaced a line...


well your master cylinder would be most peoples guess however i am over qualified in hydraulic and air break systems you need to replace your equalizer valve its on the frame on the drivers side of the vehicle

Jan 15, 2010 | 1991 GMC Sonoma

5 Answers

Stuck clutch pedal on a Mazda B series truck


Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Jul 11, 2009 | 1988 Mazda B2200

Not finding what you are looking for?
2000 Chevrolet Venture Logo

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...