Question about 2000 Jeep Grand Cherokee

Open Question

Need a wiring diagram for a 2000 4.7 L v8 jeep gc

I nee the wiring diagram for the fuel injector system

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: replacing fuel injector on jeep 2.5

Disconnect your Battery.
Remove your air intake and filter housing all the way to the throttle body. Then use a shop rag and release te pressure in the fuel system by the valve on the fuel rail. use the rag to absorb the fuel as it sprays out the fuel rail.
then you unsrew the 2 bolts holing the rail in place.
Then you pry the rail away from the manifold with a flat head.
being careful not to loose any of your injector seals.
when done clean both your injector seats and the rail seats.
use some assembly lube or shop grease to lubricate all of your injector seals upper and lower seals.
remount all parts as you dismounted.
reconnect your battery cylce the ignition key 4-5 times before starting the egine, and check for leaks. if there is no leak then go ahed and start your engine.

Posted on Jun 20, 2008

emissionwiz
  • 75055 Answers

SOURCE: 2000 jeep wrangler no injector pulse

Have you tested the PCM fuse??

Posted on Sep 17, 2008

  • 31 Answers

SOURCE: how to change fuel injectors in a 2000 jeep grand cherokee

Hi, you have to remove the fuel rail and then remove the electrical connector and then there is a clip that holds the injector to the fuel rail remove that clip and then remove the injector

Posted on Nov 18, 2009

  • 6982 Answers

SOURCE: I need a fuel pump wiring diagram for a 1993 Jeep

I don't have an isolated diagram but if you go to this link you can have the entire schematic!
http://www.scribd.com/doc/18999822/Jeep-Wiring-2
Get out your glasses and have fun!!!

Posted on Jan 18, 2010

  • 47 Answers

SOURCE: engine compartment wiring diagram for a 88 cj7

The last Cj-7 was built in 1986. And they didn't come factory with a V-8 so you have a conversion of some type. Most factory wiring diagrams aren't going to help much. Sorry

Posted on Jan 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1999 Jeep Grand Cherokee limited,V8 Quadra-trac which dies on the road; dash gauges drop; "no key" lite displays on dash. Restarts after cools. Two codes P 0443 and 0308 are showing? help


code p 0443 refers to evaporative emission (EVAP) canister purge valve ---circuit malfunction====causes ---wiring--- EVAP canister purge valve ---ECM
code p0308 refers to cylinder 8 ---misfire detected ====causes ---engine mechanical fault ---wiring----ignition/ fuel system--- injector---ECT/MAF sensor---ECM
I am thinking here that it restarts , not after cooling , but after the vacuum in the fuel tank has lessened and allowed fuel to be pumped to the injectors and the fuel pressure is re-established
if that is the case then a weak injector or partially blocked injector will misfire under those conditions
I would fix the purge valve so that the tank vents properly and the rest may go away

Feb 18, 2017 | 1999 Jeep Grand Cherokee Limited

1 Answer

Replacing Fuel Injectors


there is a 100s of pages for electrics in the FSM>
or at alldata.com
but you must know what engine you have first.

what kind of diagram. there are many, mech. electrical, , assemble, etc.
the injectors have a common 12vdc power feed.
then each injector is fired with a single wire from PCM to each injector
this is done using a power transistor in the PCM.
it acts as a switch grounding the injector for say 5/1000 of a second
and it squirts.

Mar 22, 2014 | 2002 Jeep Liberty

1 Answer

Where is the ECU located on a 2000 GC limited V8 4x4?


Give me some more information about this problem. May be i can help.

Jul 12, 2011 | 2000 Jeep Grand Cherokee

1 Answer

I have a 2004 Jeep GC 6cyl 4WD. My check engine light is on, scanned and got P0203, P0300, P303. Changed the spark plugs, fuel injector #3. Started it up and ran rough, I left it in the garage all night...


codem p 0203 refers to injector 3---circuit malfunction===causes wiring--injector--ECM
chweck for harness connection , bad wire for no 3 injector or corroded pins for no 3 injector in the connection

May 14, 2017 | 2004 Jeep Grand Cherokee

1 Answer

My 96 GC 5.2L V8 started acting up a few weeks ago by taking several turns of the key to start. Now the only way it will start is if I add starter fluid to the throttle body and once it starts it runs...


This sounds like a weak fuel pump, put a preasure gauge on the fuel rail and check the preasure with the engine off turn on the key and preasure should be 47psi to 51 psi.lower than 47 replace the pump, a few pounds make a big diffrence when trying to start,

Aug 06, 2010 | 1996 Jeep Grand Cherokee

2 Answers

Diagram for a 2000 lincoln ls V8


there are diagrams try looking at the book that came with the car or look under the hood for it some where near the front, if this dosnt work try going to a website or autozone and buy the book for the car

Mar 23, 2010 | 2000 Lincoln LS

3 Answers

Rough idle


replace map sensor

Mar 17, 2010 | 1993 Jeep Grand Cherokee

1 Answer

95 Jeep G.C. Laredo won't start


Make sure you have fully charged battery so that the engine will turn fast when attempting to start. Insure you have power to the injectors while attempting to start. If there is power there then check that you have enough fuel pressure from the pump usually 60psi or more. You can call the parts store and they can look up the pumps operating pressure. If there wasn't power to the injectors it want run. Sometimes the power source for the injectors is ran through the oil pressure switch. This switch could be sticking. Check your wiring diagram for your power source. If your engine did not turn over at all your problem would be with the starting circuit. Starter or it's power connection. I hope this helps God Bless

Sep 18, 2009 | 1995 Jeep Grand Cherokee

1 Answer

2004 Jeep G Cherokee diagnostic code open injector


It could be a faulty pcm or wiring as you stated in you post. the pcm pulses a ground to the injector circuit allowing the solenoid in the injector to activate momentarily are inject fuel into the intake. if you give me the engine size. V8 4.7L or strait 6 cylinder 4.0L and i will post the proper wiring diagram for the fuel injectors to help you out with your battle

Jan 09, 2009 | 2004 Jeep Grand Cherokee

1 Answer

2000 jeep gc wont stay running


Lock all the doors unlock the doors with the key because the security system thinks its being stolen and it shuts off the injectors
Try another key the chip in yours may be defective.

www.aceautomotive1.com

Aug 16, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

Related Topics:

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...