Question about 1992 Oldsmobile Cutlass Ciera

Open Question

1992 olds cutlass ciera 3.3 engine / engine idles high when first cranked engine light comes on / code 22 tps low voltage / engine idles fine when engine hot any suggestions ?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

alicantecoli
  • 22156 Answers

SOURCE: how to change a starter in a 1992 oldsmobile cutlass ciera

disconnect battery,three bolts hold it to bell housing and two wires ,one is the feed the other activates the solonoid Easy job to do but dirty dirt grease and muck

Posted on Jan 24, 2009

ourhowse
  • 2007 Answers

SOURCE: 1991 Oldsmobile Cutlass Ciera idles high

Change your idle control sensor, but first make sure your throttle linkage isn't sticking.

Posted on Jun 03, 2009

  • 2 Answers

SOURCE: My 1988 2.8L olds cutlass ciera stalls without

1- check for codes with scanner to see why check light coming on. 2 unbolt exhaust before caterlic convertor. Run car to see if still does it.If it does not the caterlic converter is the problem.the car temp should not go over 220 degrees. if car is getting to hot it will shut off,check cooling system and cooling fans to make sure they are comming on. Also if water is flowing through thermastat.Map sensor when gets hot could cut out. some places to look. doug

Posted on Aug 28, 2009

Testimonial: "It gave me something else to look at other the info I had. Thanks"

  • 548 Answers

SOURCE: 92 Olds Cutlass Ciera ignitian code needed

i dont have it but if you register at www.autozone.com you can get it for free and registering is free and they have all kinds of free help and diagrams for you

Posted on Sep 01, 2009

clifford224
  • 1975 Answers

SOURCE: CRANK SENSOR LOCATION FOR 1992 OLDS CUTLASS CIERA

That year Ciera came with two diiferent engines. if you have the 2.5 liter engine it is located under the hood, center, rear engine area, below ingnition coil pack and DIS module, mounted in engine block. If it is the 3.3 liter engine it is located under the hood, passenger side, lower engine area, front of crankshaft pulley, mounted in engine block. i hope this helps you and good luck.


Posted on Mar 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What would be wrong with your 88 olds cutlas ciera if you're driving down the road and car dies and won't restart?


My car did this for a while until it would no longer move and I was told all sorts of things including cleaning (all the gunk near the MAF -hosing) which made it run for a month but did idle too high. So diagnose and get the codes from your car- the paperclip way (autozone cant cause its older than 1992).
Codes I pulled pertaining to this issue were 22 (Throttle Position Sensor- TPS Signal Voltage Low) , 23 (Air Intake Temperature- MAT Low Temp Indicated), and 34 (Mass Air Flow Sensor- MAF)
Easy to DIY with these 3 sensors

Apr 22, 2013 | 1988 Oldsmobile Cutlass Ciera

3 Answers

1992 Oldsmobile cutlass ciera s 3.3 liter V6. While driving or idle in park, the idle kicks up high and the check engine light comes on. This symptom is not constant. It comes and goes sporadically. After...


Have you read out the diagnostic trouble codes? Since the check engine light has come on, there should be one or more stored diagnostic codes. Since your 1992 is before OBD-II became the standard (in the US at least) you'll need to do either the wire/paper clip method or find someone with an OBD-I scan tool for GM products.

Jun 03, 2017 | 1992 Oldsmobile Cutlass Ciera

1 Answer

Codes are reading low tps voltage, mapps high voltage ignition on low voltage at idle. Idle surges sputers and stalls when driving. Replaceed mapp and tps with no improvment?


Have you consider to check the battery power. I believe the main problem you have is either the battery or the alternator. Due to these two things with low voltage the brain ( ECU ) does not have the enough power to work. Good Luck.

Aug 15, 2012 | 1992 Chevrolet S-10 Blazer

1 Answer

My 1993 cutlas supreme stalls randomly while idling or driving , but restart right away


You will need to change the crank position sensor first and see if it corrects the problem. It is located behind the engine near the firewall. It's a bit tricky to get to it, you would need to rotate the engine forward then look under the exhaust manifold and under the cylinder closest to the drivers side. Use a 10 mm deep socket to loosen bolt. After replacement and it is still stalling then you will need to replace the ECM (vehicle computer). If it turns out to be the computer, go to your local junkyard to get an inexpensive replacement Click on the link below to view the CPS, it is around $22

http://www.partstrain.com/store/?N=0&Nr=AND(make:Oldsmobile,model:Cutlass+Supreme,year:1993,brand:Delphi,part:Crank+Position+Sensor)&ptc=S1171391678W45d204bec356b&ptid=ptc45891f6tnywz&id=Olqtv7cphi





Olds-Cutlass-Ciera.htm">http://en.allexperts.com/q/Oldsmobile-Buick-Repair-826/f/1992-Olds-Cutlass-Ciera.htm

Apr 12, 2010 | 1993 Oldsmobile Cutlass Supreme

1 Answer

92 cutlass ciera 3.3L stalls out idles eratically. trouble codes 15 16 21 26 43.i cant find the meanings for the codes


2 digit trouble codes 15coolant sensor or circuit/low temperature indicated 16system voltage out of range 21thottle position sensor[tps] or circuit vottage high 26quaddriver module circuit43low voltage at ecm terminal l [carbureted models]

Feb 17, 2010 | 1992 Oldsmobile Cutlass Ciera

3 Answers

Code 16 on a 1990 olds cutlass ciera


Code 16 on my repair manual shows a low voltage to the ECM (computer). Try cleaning the 2 fuse connectors that supplies battery voltage to the ecm. The fuse box is on the front drivers side of the engine compartment. I have the same problem with my car with a intermitten fast idle and check engine light.

Sep 22, 2009 | Cars & Trucks

1 Answer

1991 Cutlass Ciera 3.3 low idle


Idle Control Solinoid Will Cause this with No Engine Light. = ICS

Jul 15, 2009 | 1991 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1992 Oldsmobile Cutlass Ciera Logo

Related Topics:

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...