Question about 2006 Jeep Commander

Open Question

How to remove rear rotor on a 2006 jeep commander

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

greg_margo
  • 1959 Answers

SOURCE: Jeep Commander Rear Brake Pad Installation

Per Chilton Auto repair manual:

Removal & Installation

  1. Raise and safely support the vehicle.
  2. Remove the rear wheel.
  3. Siphon a small amount of brake fluid from the master cylinder reservoir.
  4. Insert a small prybar through the caliper opening and pry the caliper cover (using the outboard brake pad) to bottom the piston in the caliper bore.
  5. Remove the caliper slide bolts.
  6. Remove the caliper from the anchor.

    WARNING Support the brake caliper with mechanics wire. Do not let the caliper hang by the brake hose.
  7. Remove the brake pads from the caliper.
To install:
  1. Install the brake pads onto the caliper.
  2. Lubricate the slide pin bolts with grease provided with the brake pads, or suitable silicon grease equivalent.
  3. Install the caliper on the anchor and tighten the slide pin bolts to 18 ft. lbs. (25 Nm).
  4. Install the rear wheel.
  5. Lower the vehicle.
  6. Pump the brake pedal several times until a firm pedal is obtained in order to properly seat the pads.
  7. Refill the brake fluid reservoir to the proper level.

Posted on May 17, 2009

  • 83 Answers

SOURCE: How do I replace the rear brake light bulb on a

Get manual at AUTOZONE!! swampratt200!!AAAEEE!!!!

Posted on Jul 22, 2009

  • 645 Answers

SOURCE: ac/heater fan switch problem on a 2006 jeep commander

next to the fan motor there should be a connector that has three or four wires that attached to the blower resistor. it should have two screws holding it to heater case, just pull it out and replace.

Posted on Feb 13, 2010

Testimonial: "This info was very helpful but need a little more info of where the fan motor is located. I will post another question to find that info."

Gozer
  • 435 Answers

SOURCE: install a altenator for a 2006 jeep commander

I would rate this a 5 in difficulty. If you have a metric socket set, basic hand tools and a supertine belt tool it's fairly easy repair. You can rent a surpentine belt tool at Autozone.

Disconnect the battery
remove the cowling
remove the supertine belt from the altenator pully
disconnect the red wire on the back of the altenator
disconnect the harness plug from the altenator
remove the bolts holding the altenator to the mounting brackets.
Reverse the process with the new altenator and it it's done.
Make sure your battery is charged before you start the engine a low battery can cause damage to your new altenator.

Posted on May 21, 2010

alicantecoli
  • 22095 Answers

SOURCE: 2006 Jeep Commander inefficient catalyst

most likely the oxygen sensors (lambada) ,they need changing ,their are two one before the cat and one after,do not think you need a new cat unless it has a min of 150.000 miles on the clock

Posted on Jul 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove front brake rotors


The caliper needs to be removed by removing the two bolts on the back side of the caliper. Make sure that there is no kinda clip on one of the lug bolts. If the rotor is stuck a few whacks on the rear of the rotor with a rubber mallet should pop right off. I hope its a little helpful.

Jun 06, 2015 | 2006 Jeep Grand Cherokee

1 Answer

How to replace rear brake rotors on 06 commander?


I Just replaced my rotors on a commander that I've owned for for 6 years. once you get the tire and brake caliper assembly off. You will need to make sure the the Parking/emergence brake is not engaged, if it is the drum brakes under the rotor will give you a very hard time. Finally if you know you are getting rid of the rotor take a good heavy hammer or mallet and wack away at the disc portion of the rotor. i would go around the rotor top to bottom, side to side till it comes loose. don't be afraid to hit it hard. I would recommend eye protection.

Jun 28, 2014 | 2006 Jeep Commander

1 Answer

JEEP COMMANDER REAR BRAKES DRUMS OR DISC?


It has both. the emergency break is a drum brake, under the inner portion of the rotor

May 12, 2014 | 2006 Jeep Commander

1 Answer

Replace front rotors


if this job scares you take the car to a brake shop..if not you can remove the wheel and remove the caliper assembly, and the rotor should slide right off the hub drive..some models have a retainer assembly that gets taken off also in the center of the rotor behind a cover..good luck parts stores can print out step by step intructions for you..

Jan 20, 2013 | 2006 Jeep Commander

1 Answer

How to get the rear driver side rotor off after removing the pads and the caliper, the rotor is catching on the drum emergency brake


there should be a gold or silver nut in the hole in the center of the rotor. take that off and the rotor should pull out.

Nov 20, 2010 | 2006 Jeep Grand Cherokee

1 Answer

How do I remove rear rotor to have them turned?


jack up wheel, remove wheel,remove brake caliper, slide of rotor.Note use a clothes hange to hold up brake calpier as you do not want to break the brake line. Good Luck Tim

Sep 11, 2010 | 2006 Jeep Commander

1 Answer

Jeep Commander Rear Brake Pad Installation


Per Chilton Auto repair manual:

Removal & Installation
  1. Raise and safely support the vehicle.
  2. Remove the rear wheel.
  3. Siphon a small amount of brake fluid from the master cylinder reservoir.
  4. Insert a small prybar through the caliper opening and pry the caliper cover (using the outboard brake pad) to bottom the piston in the caliper bore.
  5. Remove the caliper slide bolts.
  6. Remove the caliper from the anchor.

    WARNING Support the brake caliper with mechanics wire. Do not let the caliper hang by the brake hose.
  7. Remove the brake pads from the caliper.
To install:
  1. Install the brake pads onto the caliper.
  2. Lubricate the slide pin bolts with grease provided with the brake pads, or suitable silicon grease equivalent.
  3. Install the caliper on the anchor and tighten the slide pin bolts to 18 ft. lbs. (25 Nm).
  4. Install the rear wheel.
  5. Lower the vehicle.
  6. Pump the brake pedal several times until a firm pedal is obtained in order to properly seat the pads.
  7. Refill the brake fluid reservoir to the proper level.

May 17, 2009 | 2006 Jeep Commander

1 Answer

Brake problems


the front rotors are warped,they need to be replaced

May 15, 2009 | 2006 Jeep Commander

Not finding what you are looking for?
2006 Jeep Commander Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...