Question about 2006 Ford Fusion

Open Question

P0053 bank 1 sensor 1 oxygen sensor was changed but the check engine light keeps coming on

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: Ford Windstar 1996 Trouble Codes P0171, P0141, P0161, and P0174

Bank one is toward the front of the vehicle. Sounds like the heated oxygen sensors have gone bad. The Oxygen Sensors are located in the exhaust pipe and require a special socket to remove and replace.

Posted on Jan 16, 2009

warlock61
  • 659 Answers

SOURCE: check engine light

this is very common on these. the upper intake seals leak and should be replaced. It is not a noticable vacuum leak and is usually worse when the engine is cold. It is not a very difficult job to do

Posted on Mar 01, 2009

greg_margo
  • 1959 Answers

SOURCE: check engine light 97 ford explorer. obd-II po141

Looked up your OBD II code for your Explorer and got the following: Bank 1 Sensor 1
The possible causes are listed below per Chilton: *same result for all engines available on your vehicle

Trouble Code: P0141 (4.0L V6 VIN E Auto)
HO2S-11 Heater Circuit (Bank 1, Sensor 1) Print this code dataprint_icon_codes.gif
Number of Trips to Set Code: 2
OBD II Monitor Type: CCM Details
Indicators: MIL Details
Trouble Code Conditions:
During testing the heated oxygen sensor (HO2S) heaters are checked for open and short circuits and excessive current draw. The test fails when the current draw exceeds a calibrated limit or an open or short circuit is detected.
Possible Causes:

  • Vacuum hose disconnected on exhaust gas recirculation (EGR) system module (ESM) applications* Short to VPWR in the harness or HO2S
  • Water in the harness connector
  • Open VPWR circuit
  • Open GND circuit
  • Low battery voltage
  • Corrosion or incorrec
The sensors themselves appear in the illustration linked to below. The illustration is for the Ford Ranger but indications are that other models have similar locations. Hope this helps with your problem. Best of luck!
Greg

http://www.chiltonlibrary.com/content/images/8968/images/89684g23.pdf

Posted on May 17, 2009

emissionwiz
  • 75797 Answers

SOURCE: Replacing bank 1 sensor 2 and bank 2 sensor 1 oxygen sensors

BANK ONE IS THE REAR BANK OF CYLINDERS AND TWO THE FRONT BANK

Posted on Jun 24, 2009

bschilz
  • 2049 Answers

SOURCE: location of the bank 1 sensor 2 O2 sensor on a 2001 ford escape

B1 means the sensor is located on the same bank of the engine that has the #1 cylinder. B2 is located on the opposite bank.
S1 means the sensor is located BEFORE the catalytic converter
S2 means the sensor is located AFTER the catalytic converter

You didn't say which engine you have, so I've included the diagrams of both 4 cyl and 6 cyl so you can see the banks

7acfed1.gif
d9eb1af.gif

Posted on Oct 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 toyota alvalon check engine light keeps coming on for code p0171 after replacing 02 oxygen sensor in bank 1


code p 0171 refers to system too lean bank 1===causes ---intake /exhaust leak---AIR system---MAF/VAF sensor/s---fuel pressure/ pump---injector/s---heated oxygen sensor (HO2S) the one in the exhaust manifold for bank 1 nearest the firewall

Apr 15, 2017 | Toyota Cars & Trucks

1 Answer

06 Chevy Silverado code p0053 and p0135


DTC P0053 HO2S Heater Resistance Bank 1 Sensor 1
• DTC P0135 HO2S Heater Performance Bank 1 Sensor 1
Important: Whenever the heated oxygen sensor (HO2S) heaters are commanded ON with a scan tool, they will continue to be pulsed ON once per second until the ignition is turned OFF for 30 seconds.
Turn ON the ignition, with the engine OFF.
Command the HO2S heaters ON with a scan tool.
Wait 15 seconds to allow the HO2S heater current to stabilize.
Observe the affected HO2S Heater Current parameter with a scan tool.
Is the HO2S Heater Current parameter within the specified range?
0.25-1.375 A

Sep 10, 2016 | 2006 Chevrolet Silverado

1 Answer

Codes p0054 p0141 p0036


code p0054 is
Possible causes - Faulty Heated Oxygen Sensor Bank 1 Sensor 2
- Heated Oxygen Sensor Bank 1 Sensor 2 harness is open or shorted
- Heated Oxygen Sensor Bank 1 Sensor 2 circuit poor electrical connection
When is the code detected?Heater current requirements too low or high in the heated oxygen sensor (HO2S) heater control circuit Symptoms- Engine Light ON (or Service Engine Soon Warning Light)
code p0141 is O2sensor heater circuit malfunction( bank one sensor 2)
there is chance that wire from that sensor is touching,part of your exhaust system,and either is open or shorting to ground

code p0036
036 - HO2S Heater Control Circuit Bank 1 sensor 2check the wire from the sensor for the sign cut or melting,and change the sensor

Apr 18, 2013 | 2006 Chevrolet Suburban 1500

1 Answer

2002 toyota avalon engine check light on P0078 and P007C


P0050 HO2S Heated Oxygen Sensor -Control Circuit (Bank 2 Sensor 1)

P0051 HO2S Heated Oxygen Sensor -Control Circuit Low (Bank 2 Sensor 1)

P0052 HO2S Heated Oxygen Sensor -Control Circuit High (Bank 2 Sensor 1)

P0053 HO2S Heated Oxygen Sensor -Resistance (Bank 1 Sensor 1)

P0054 HO2S Heated Oxygen Sensor -Resistance (Bank 1 Sensor 2)

P0055 HO2S Heated Oxygen Sensor -Resistance (Bank 1 Sensor 3)

P0056 HO2S Heated Oxygen Sensor -Control Circuit (Bank 2 Sensor 2)

P0057 HO2S Heated Oxygen Sensor -Control Circuit Low (Bank 2 Sensor 2)

P0058 HO2S Heated Oxygen Sensor -Control Circuit High (Bank 2 Sensor 2)

P0059 HO2S Heated Oxygen Sensor -Resistance (Bank 2 Sensor 1)

P0060 HO2S Heated Oxygen Sensor -Resistance (Bank 2 Sensor 2)

P0061 HO2S Heated Oxygen Sensor -Resistance (Bank 2 Sensor 3)

P0062 HO2S Heated Oxygen Sensor -Control Circuit (Bank 2 Sensor 3)

P0063 HO2S Heated Oxygen Sensor -Control Circuit Low (Bank 2 Sensor 3)

P0064 HO2S Heated Oxygen Sensor -Control Circuit High (Bank 2 Sensor 3)

P0065 Air Assisted Injector -Range/Performance

P0066 Air Assisted Injector -Circuit Malfunction or Circuit Low

P0067 Air Assisted Injector -Circuit High

P0068 (MAP) Manifold Absolute Pressure /(MAF) Mass Air Flow - Throttle Position

Correlation

P0069 (MAP) Manifold Absolute Pressure / (BARO)Barometric Pressure Correlation

P0070 Ambient/Outside Air Temperature Sensor -Circuit Malfunction

P0071 Ambient/Outside Air Temperature Sensor -Range/Performance Problem

P0072 Ambient/Outside Air Temperature Sensor -Circuit Low Input

P0073 Ambient/Outside Air Temperature Sensor -Circuit High Input

P0074 Ambient/Outside Air Temperature Sensor -Circuit Intermittent

P0075 Intake Valve Control Solenoid Circuit Malfunction (Bank 1)

P0076 Intake Valve Control Solenoid Circuit Low (Bank 1)

P0077 Intake Valve Control Solenoid Circuit High (Bank 1)

P0078 Exhaust Valve Control Solenoid Circuit Malfunction (Bank 1)

P0079 Exhaust Valve Control Solenoid Circuit Low (Bank 1)

P0080 Exhaust Valve Control Solenoid Circuit High (Bank 1)

P0081 Intake valve Control Solenoid Circuit Malfunction (Bank 2)

P0082 Intake Valve Control Solenoid Circuit Low (Bank 2)

P0083 Intake Valve Control Solenoid Circuit High (Bank 2)
P0084 Exhaust Valve Control Solenoid Circuit Malfunction (Bank 2)

Mar 22, 2013 | 2002 Toyota Avalon

1 Answer

2006 Expedition Sensor fault P0053


Bad oxygen sensor, bank 1 sensor 1

Aug 01, 2012 | 2006 Ford Expedition

2 Answers

What's your problem?service engine soon light on code P0132,P2195, P2196


P0132 FORD - O2 Sensor Circuit High Voltage Bank 1 Sensor 1xicon.jpghttp://engine-codes.com/p0132_ford.htmlForum CodePossible causes- Front Heated Oxygen Sensor Bank 1 harness is open or shorted
- Front Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Faulty Front Heated Oxygen Sensor Bank 1
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks
P2195 - O2 Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1

P2196 - O2 Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1

Jun 29, 2012 | Ford Cars & Trucks

2 Answers

Check Engine light with Po131 o2 circuit low voltage sensor 1 bank 1 reading, what does that mean?


- Front Heated Oxygen Sensor Bank 1 harness is open or shorted
- Front Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Faulty Front Heated Oxygen Sensor Bank 1
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks

Replacing the O2 Sensor 1 usually takes care of the problem

The front heated oxygen sensor (or O2 sensor 1) is placed into the exhaust manifold. It detects the amount of oxygen in the exhaust gas compared to the outside air. The heated oxygen sensor 1 has a closed-end tube made of ceramic zirconia. The zirconia generates voltage from approximately 1V in richer conditions to 0V in leaner conditions. The heated oxygen sensor 1 signal is sent to the Engine Control Module (ECM). The ECM adjusts the injection pulse duration to achieve the ideal air-fuel ratio. The ideal air-fuel ratio occurs near the radical change from 1V to 0V.

Feb 07, 2012 | 2004 Honda Odyssey

2 Answers

1996 Toyota 4runner 3.4L error code p0133


SAE J2012 Revised DEC2007 lists Diagnostic Test Code (DTC) P0133 as "O2 Sensor Circuit Slow Response Bank 1 Sensor 1"

This code basically means that the upstream oxygen sensor on bank one of your engine is not responding as quickly as it should to changes in oxygen leavels in the exhaust.

The usual causes of this is an oxygen sensor that is just plain worn out (if it has a lot of miles on it) or an oxygen sensor that is contaminated by engine oil or antifreeze leaks causing these fluids to be burned in the exhaust (like bad piston rings, defective PCV valve, blown head gasket, etc.).

In any case, the oxygen sensor needs to be replaced. However it should be noted that if it is caused by contamination like that described above, replacing it will only result in a new oxygen sensor doing the same thing if the cause of the contamination is not repaired.

Jan 24, 2012 | Toyota 4Runner Cars & Trucks

2 Answers

2007 Chevy Tahoe check engine scan codes: P0030, P0053, PO135 ~ Please advise or help : ( thought that advanced auto would have been a bit more helpful than handing me a piece of paper with codes and...


There is a fault with the inbuilt heater in the oxygen sensor, before the catalytic converter, on the exhaust pipe the same side of the engine as cylinder 1. The oxygen sensor has four wires within the cable sheath to the top of it. Two of the wires will share the same color. These wires supply power to an internal heating element wire within the sensor. Follow the cable from the oxygen sensor to the connector, you can do a lot testing here. Check the resistance between the two 'same coloured ' wires. The resistance is low, somewhere between 1 and 10 ohms. If there is no continuity (infinite resistance) then this is the fault and the sensor needs to be replaced. The codes: P0030 the oxygen sensor heater relay is at fault P0053 Oxygen heater resistance error P0135 Sensor 1 bank 1 error You are looking at replacement. A further confirmation take the connection from sensor 1 bank 1 and swap it with the sensor 1 bank 2 on the other side of the engine. The codes should 'transfer' and show P0036; P0059 and P0141.

Apr 26, 2011 | 2007 Chevrolet Tahoe

1 Answer

Check engine light on- auto zone scanner shows error code p0053 probable cause: 1.-check circuit fuse 2.-relay defective 3.-check circuit wiring Where are fuse and relay located?


The code P0053 is for your Bank 1 Oxygen Sensor, the closest Oxygen Sensor to the engine, connected to the Exhaust. Replace your Oxygen Sensor, clear the code, and see if it comes back.

Mar 12, 2011 | Chevrolet Suburban 1500 Cars & Trucks

Not finding what you are looking for?

Open Questions:

See all 2006 Ford Fusion Questions

2006 Ford Fusion Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...