Question about Dodge Ram Pickup 3500

Open Question

REAR AXLE BEARING TORQUE 5500 DODGE - Ram Pickup 3500 Dodge Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: torque specs 7.5 inch rear axle 96 ford ranger

Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in

Posted on Jan 30, 2009

Ad
  • 4 Answers

SOURCE: how tight should i make the axle nut after fitting

tighten the nut down and spin the hub to set the bearings and then back it of a 1/4 turn

Posted on Nov 13, 2009

co7196
  • 3433 Answers

SOURCE: torque procedure on american axle 11.5

Tight tight rtight tight and so on alternating criscross pattern

Posted on Nov 17, 2009

roniecon
  • 6826 Answers

SOURCE: Replaced rear axle pinion bearing and seal, need

There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to aquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Posted on Apr 19, 2010

gh20s
  • 343 Answers

SOURCE: 96 chevy blazer rear axle bearing/seal r/r

No. Did you run some emery cloth along the race (bearing surface) to make sure it was smooth and clean? If you leave any part of the old seal or debris on the hub surface, damage the seal when installing it, not liberally packing the bearing with grease or the seal did not seat right you can have issues like yours. Make sure the seal is installed flush and if everything looked good as far as the axle and surfaces, pack more grease in the bearing. When you think there is enough grease in it, put more in. Put the grease in the palm of your hand and with the bearing held flat in the other hand repeatedly tap the bearing on your palm until grease comes out both sides. Then put more on it when you seat it.

Posted on May 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs for rear axle bearing hub & axle nut on 2006 dodge magnum sxt.


Go to autozone dot com and make a free account, put in the year and make and model then look for the free repair guides. They are online Chilton books and they will have it.

Jun 14, 2015 | 2006 Dodge Magnum SXT

1 Answer

Need torque specs for front wheel bearing on 2004 dodge 3500 dually


The hub bearing retaining bolts are 150 ft. lbs the center axle nut primary torque 135 ft.lbs rotate 5-10 times increasing torque by 50 ft.lbs until final torque of 265 ft.lbs is reached

Mar 23, 2014 | 2004 Dodge Ram 3500 Truck

1 Answer

Looking for torque spec for bolts holding the rear shocks on the rear of a 2006 Dodge Sprinter 3500


Hello acadiamaine,

If the shock absorber bolt to the axle is a 14mmX1.5 it should be torqued to 110 Nm if it is a 12mmX1.5 bolt torque it to 70 Nm.

The bolt to the frame side should be torqued to 140 Nm if the axle bolt is 14mmX1.5 and 80 Nm if the axle bolt is 12mmX1.5.

I hope this helps.

Regards,

Jerry

Sep 15, 2011 | Dodge Sprinter Cars & Trucks

1 Answer

How to remove rear wheel bearings on my 1999 Ford Expedition and how do i know what pulley to rent/buy?


The 1999 Ford Expedition is built on an F150 platform. The Expedition uses a 9.75-inch rear axle. The axles are retained with C-clips at the end of the axle shaft, inside the differential carrier. The axle bearings are of the roller type. A failed axle bearing can manifest itself as a noise at the rear wheel or gear oil leaking past the oil seal. When replacing axle bearings, the oil seals must also be replaced.
Torque the caliper mounting bolts to 30 foot-pounds. Torque the bolt to 20 foot-pounds with a torque wrench and socket. Click this link below for complete detailed procedure:--- http://technoanswers.blogspot.com/2011/06/how-to-remove-rear-wheel-bearings-on.html -------------- This should help.Thanks.Helpmech.

Jun 07, 2011 | Ford Expedition Cars & Trucks

1 Answer

I need the torque specs on a rear axle pinion nut for a 2003 Dodge Ram 2500 4/4 Cummins, Automatic.


The pinion nut does not have a torque spec. as in how tight the nut is. The amount of torque is measured in bearing preload. You will need a "torque to rotate" torque wrench. If you are using new bearings the torque spec. is 15-25 in. lbs. If you are using your old bearings the torque spec. is 10-20 in. lbs to rotate. To measure this you will need to tighten the nut in small increments then use the torque to rotate wrench to turn the pinion without the carrier/ ring gear installed. Repeat until desired torque is reached.

Jan 29, 2011 | Dodge Ram 2500 Cars & Trucks

1 Answer

Replaced rear axle pinion bearing and seal, need to know pinion nut torque spec. for aam rear axle 2005 dodge 3500 4x4 Thanks.


There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to aquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Apr 19, 2010 | 2005 Dodge Ram

1 Answer

Torque procedure on american axle 11.5


Tight tight rtight tight and so on alternating criscross pattern

Sep 29, 2009 | 2007 Dodge Ram 3500 Quad Cab Laramie

1 Answer

Need to remove and replace rear rotor


You have to remove the axle shafts first as it has a full-floating axle, then pull rotor and hub off the axle housing. Unbolt rotors from hub. Check bearings and seals in hubs and the axle snouts where the bearings run before installing. Put new flange gaskets on axle and torque flange bolts to 95 ft-lbs.

Apr 11, 2009 | 2004 Dodge Ram 3500 Truck

1 Answer

Torque specs 7.5 inch rear axle 96 ford ranger


Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in

Jan 30, 2009 | 1996 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

654 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...